Search Documents

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By B. A. Day

The traditional view taken of commodity prices is that they are cyclical, with strong demand boosting prices and attracting new suppliers. The resulting increased supply pushes prices down with consequent exit of the higher cost producers. And so the process repeats itself. Little attention is given to shifts in underlying global issues and their effect on the traditional process which is seen as being controlled by ?amorphous? market forces with producers profiting from the good times and trying to survive in the bad.. The questions posed are: does this still apply and will it apply into the future? What new factors are affecting the cycles? Can we expect to find the traditional commodity cycles repeated in the 21stcentury? Are producers powerless within the forces of the cycles? Forces likely to affect future commodity prices will be suggested, using gold, zinc, copper, tin and coal as case studies. The long-term downward trend in the real price of commodities is identified.

Jan 1, 2000

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By M. McWha

Laboratory bias is a universal problem in all branches of analytical science. It results from differences in methods, techniques, equipment, and calibrations between laboratories. Notwithstanding that it is a property that can be measured by the use of standards or by inter-laboratory testing, laboratory bias remains a material issue for the mining industry. There is extensive literature and clear guidelines on measurement from the International Organization for Standardization (ISO) and its worldwide federation of national standards bodies (ISO member bodies) and from the science of metrology. ISO guides cover the manufacture and use of standards. An accessible source of literature covering laboratory quality control comes from the public health sector, particularly pathology. There is little doubt in financial reporting rules about the meaning of materiality. Public reporting guidelines are clear that material matters need to be disclosed for investors. Unfortunately there is currently no clear guidance what to do about biased assay results in mineral industry public reporting guidelines. This paper reviews the requirements for the manufacture and use of reference materials, public reporting requirements in the mining industry, and presents proposals to improve management and reporting of laboratory biases. Keywords laboratory bias, reference materials, ISO Guides, financial reporting, materiality.

Jan 1, 2014

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

By B. Unver

Effective strata control is a prerequisite for maintaining an efficient mining operation. If the strata in the vicinity of an opening are not controlled effectively, it is impossible to perform a safe, efficient and economical operation. In this paper, the reasons and outcome of instability problems observed in roadways opened in clay and marl at the Bolu Colliery of Yeni Çeltek Establishment are investigated. Roadways under examination were located in a syncline causing high residual tectonic stresses. Factors affecting the instability have been studied thoroughly by examining geology and tectonics of the area, establishing convergence measuring stations to understand in situ behaviour of supports and laboratory tests to determine engineering properties of samples taken from nearby convergence measurement stations. As a conclusion, a new production strategy and a new support system are recommended to maintain stability.

Jan 1, 1999

By J. Gunaselvam

This article deals with an investigation into the specification and use of appropriate seating systems to reduce whole-body vibration (WBV) exposure in typical vehicles used in the SA mining industry. The EU Directive EU/44/2002 to be legislated in 2005 in European countries, provides legal and economic motivation for this project. The criteria for seat selection can be condensed to the requirements in the directive, which mandates an action level of 0.5 m/s2and a vibration exposure limit of 1.15 m/s2 for an equivalent 8-hour daily exposure period. As part of this study six suspension seats, which the manufacturers claim satisfy the requirements in ISO 70966, were tested to determine the most suitable seat for an articulated dump truck. Six test subjects, three ?light? and three ?heavy? as specified in ISO 70966, were used to estimate the seat transmissibility functions in the vertical direction of the six different suspension seats. Transmissibility functions were measured in the laboratory with two excitation levels of 1 m/s2 and 2 m/s2 r.m.s. in the 0.5?30 Hz frequency range, as well as one spectrum approximating the EM5 spectral class. SEAT values were calculated for road vibration data measured on a typical articulated dump truck. A set of seat selection guidelines that can be followed by vehicle manufacturers and suppliers, procurement officers and and the technical staff on a mine is proposed in this article. It is recommended that additional studies of the use and operating conditions of seating systems in the SA industry, as well as an epidemiological survey be commissioned to gather additional information on this subject. Nomenclature ADT Articulated dump truck DSTF Dynamic seat testing facility EM1 Frequency spectra associated with earth moving equipment (?articulated or rigid frame dumper?) according to ISO 7096 EU European Union ISO International Standards Organisation PSD Power spectral density r.m.s .Root mean square SEAT Seat effective amplitude transmissibility WBV Whole-body vibration

Jan 1, 2005

By B. Clermont

Ball mills are usually the largest consumers of energy within a mineral concentrator. Comminution is responsible for 50% of the total mineral processing cost. In today?s global markets, expanding mining groups are trying to optimize mill performances. Since comminution is concerned with liberating valuable minerals for recovery in the separation process, it is crucial to run the mills at the best operating conditions which lead to good liberation at competitive throughputs with minimum costs (energy and wear). The high availability of the equipment is also essential to maximize production and profit. To reach this key objective, continuous and reliable information about the mill operation is vital. An innovative tool which can deliver information about in-mill dynamics has been developed by Magotteaux. It can provide online and accurate measurements of the degree of grinding ball fill and pulp position for timely decision making and actions. This tool could be used on its own or linked to an automatic grinding ball loading system named Magoload. Therefore, ball load could be kept constant by using direct measurement. This article describes the Sensomag and presents some of the major improvements that can be achieved with it. Some other promising avenues are still to be explored. Keywords: Comminution, process control, process optimization, process instrumentation, online analysis.

Jan 1, 2010

By H. A. D. Kirsten

Shotcrete has become a strategic component of support in underground mines. The ductility of reinforced shotcrete makes it a safe and economic means of surface support under adverse static and dynamic loads. The ability of ductile shotcrete to sustain load at large deflections enables excavations in squeezing conditions to be stabilized and the safety in excavations subject to rock bursting, to be assured. A Shotcrete Working Group was formed to find the configurations of fibre reinforcement that would give shotcrete the same ductility as when reinforced with mesh. Beams and panels reinforced with various types and lengths of fibre were accordingly tested. A single mix design consisting of river sand, ordinary Portland cement, fly ash, condensed silica fume and gunite dust and segregation suppressant was used. Steel and polypropylene fibre varying in length from 25 to 50 mm were used in nominal contents of 5 % and 0.5% by mass respectively. Beams, panels and control specimens were shot into specially made formers. Suitable mixing procedures were developed for the different types of fibre. The test specimens were shot in a semi-dry mix process. The shotcrete was cured until tested 28 days after shooting. The fibre contents and uniaxial compressive and Brazilian tensile strengths of the shotcrete were determined from the control specimens. The beams and panels were tested in bending in specially manufactured test rigs. The beams were examined for simple supports and fixed ends. The panels were fixed in a manner that simulated underground conditions and were loaded statically under uniform pressure. The beams were loaded and the corresponding deflections measured up to failure. The panels were loaded up to mid-span deflections of 150 mm. The results are presented in the form of load-deflection graphs. The peak loads and ultimate deflections for the fixed end beams were considerably larger than for the simply supported beams for the various types of fibre considered. None of the beams tested, however, were able to sustain load at relatively constant value beyond the peak load. The panel tests showed that 40 mm and 50 mm long steel fibre and 30 mm, 40 mm and 50 mm long monofilament polypropylene fibre reinforcement gave shotcrete the same ductility as mesh.

Jan 1, 1998

By P. E. Hand

Coal is a complex heterogeneous commodity that can be mined in a number of ways and needs to be processed to a homogeneous quality that satisfies the customer?s requirements, while attempting to maximize revenues. Only a small proportion of coal is suitable for metallurgical use. Export coals cover a wide range of qualities and some coals can be used optimally in the raw state for energy production. Critical quality parameters vary and can be a combination of heat value, ash, volatiles, sulphur, phosphorus, sizing, amongst others. The level of beneficiation is generally dictated by the washability of the coal, mining contamination, and the target product quality. The steps in the coal chain covered in this paper comprise exploration, mining selections, production, the washing process, and product delivery. Many points of sampling are needed to maximize yield at the correct quality, and some of these will be described in the paper. Keywords coal chain, coal beneficiation, sampling.

Jan 1, 2014

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By I. C. Spangenberg

The status of sampling practices in the gold mining industry in Africa was determined as an initial step in a process to standardize sampling practices in the mining industry. Twenty-one gold mines, twenty metallurgical plants, and thirteen laboratories were rated for the potential influence of the relevant sampling errors on each component of the particular sampling system. The findings of the study on the status of equipment, standards, procedures, and management principles were presented in a dissertation (Spangenberg, 20121) and are now used by AngloGold Ashanti?s mines in the quest for correct sampling practices. The information is also used to compile a guideline on leading practice procedures for sampling methods in gold mining. This article is an overview of sampling best practice found in African mining Keywords theory of sampling, best practise, sampling errors, sampling standards.

Jan 1, 2014

By C. J. Badenhorst

The scope of this project was to research, develop and eventually produce a personal occupational hygiene and safety exposure monitor system to assist in recording and analysing various stress factors that could affect the health, wellness and safety of employees, i.e. that could result in injury or ill health of workers, create stress build-up within individual workers that could negatively affect worker alertness and safety, and, may even result in permanent disability or death. Utilized systems at the time were all reactive, whereas the DOHEMS (Proactive Digital Occupational Hygiene and Safety Exposure Monitoring) System enabled the measurement of exposure (and associated risk) in a proactive manner via real-time exposure and digitized recordings. The idea of the development was to create a unit that is so cost effective, small and light that every worker can use a system on a daily basis. The development will eventually replace current, bulky and expensive monitoring equipment. The device must be a portable battery operated device and monitor the immediate working environment by periodic sampling for vibration, noise, toxic gasses (NO/NOX/CO/VOC, etc.), body temperature and heart rate. The samples must be time and date stamped, utilizing a real-time clock (RTC) synchronized with the closest regional secondary time source and related to synchronized real-time video captured samples. These samples are then recorded onto a rugged non volatile storage device with the capacity to store a vast number of samples covering the entire working shift of eight (8) hours plus. The system has been fitted with a clear visual local alarm indication system, indicating any excessive exposures or stresses, for the worker?s supervisor to respond to. This system allows for a pro-active approach. The system is also a wireless system (to the external environment) so as to not affect the mobility of an employee and flameproof to allow for use in explosive environments. Keywords: safety, digital, exposure, monitoring, proactive.

Jan 1, 2010

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

The 106th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22 Erlswold Way, Saxonwold, Johannesburg on Wednesday, 13th August, 2003. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Kevin Moxham, President, Association of Mine Resident Engineers Prof. Jay Barton, Vice President, The Geological Society of South Africa Dr Gus Muller, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Marius van Rooyen, President, Institute of Mine Surveyors of South Africa Benjamin Ngulube, Deputy Vice President, South African Institution of Electrical Engineers Dr Francois Malan, Chairman, South African Institute of Rock Engineering Dr Paul Jourdan, President, Mintek

Jan 1, 2003

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By S. E. Olsen, M. Tangstad

The main source of Mn in raw materials for SiMn production is Mn-ore and Mn-rich slag from the high carbon FeMn production. The amount of slag per tonne of SiMn metal is mainly determined by the ore/slag ratio. Increasing share of FeMn slag at expense of Mn-ore will lead to larger slag/metal ratio in the SiMn process. High volume of slag leads to an increased consumption of energy and probably to higher losses of metal inclusions in the final slag. Excavation of a SiMn furnace has shown that only modest pre-reduction of Mn-ore with CO gas seems to be obtained. Nearly all reduction of MnO was finished at the top of the cokebed. Dissolution and reduction of quartz obviously takes place in the cokebed zone after the main reduction of manganese oxide is finished. Probably the ?pick up? of Si in the metal is quite fast and takes place as the metal trickles down through the cokebed towards the metal bath. The distribution of Si between SiMn alloys and multicomponent MnO-SiO2-CaO-Al2O3-MgO slags is mainly determined by the process temperature, the silica content of the slag and its R-ratio = (CaO+MgO)/Al2O3. As an example, the equilibrium content of Si in the alloy will increase by about 6 % if the R-ratio is reduced from 2 to 1, provided constant temperature and silica content. The effect of temperature is also considerable. The equilibrium content of silicon will increase by approximately 6 % per 50°C in the temperature range 1550°C to 1700°C. The equilibrium content of MnO in SiMn slags depends first of all on the temperature and secondly on the silica content of the slag. At 1600°C the MnO content decreases from about 9 % at silica saturation to a minimum of about 3-4% when the silica content is reduced to about 40-45%.

Jan 1, 2004