Search Documents

By Willard L. Hunter

The separation of tantalum and columbium by solvent extraction was under-taken as part of the Bureau of Mines research program to improve methods for extracting, separating, and reducing these elements to metal. The diethyl ketone aqueous HCl-HF system was one of several systems studied to determine the effect of metal and acid concentrations in aqueous solutions upon the transfer of tantalum and columbium into selected ketones. The tantalum-columbium oxide mixture used in this investigation was obtained by chemical extraction from Geomines slag. The investigation showed that tantalum 99.4 percent pure and columbium 97.2 percent pure can be produced by the selective transfer of tantalum into diethyl ketone from a solution of 2-N HF and 1-N HC1. The relatively low acid concentration necessary for tantalum transfer and the excellent selectivity of the system recommend its use for the separation of tantalum and columbium.

Jan 1, 1961

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

By Oscar Lee

"Flotation is generally regarded as a process that is only applicable to metallic minerals. However, its scope is now known to be greater than this, because some of the nonmetallic minerals are floatable, such as graphite, sulphur, and fluorite. Recent observations show that limestone may be added to the list of floatable nonmetallic minerals. Such work is being done on a laboratory scale at the Southern Experiment Station (Tuscaloosa, Ala.) of the Bureau of Mines, Department of Commerce, where experimental magnetic concentration of the low-grade iron ores of the Birmingham district is in progress. Certain experiments have demonstrated that the limestone may be floated from the magnetic log-washer tailing, and then incorporated in the iron concentrate.If the loss of lime could be prevented, some ores though low in iron and high in insoluble contain enough lime to make their concentrates self-fluxing. Since this loss in the magnetic log-washer can not be avoided, the Time must be recovered from the tailing by some method and added to the magnetic iron concentrate before sintering. Then the resulting concentrate will be self-fluxing.While seeking a suitable means of treating the tailing for recovery of lime, flotation was tried. It was at once evident that this method had possibilities, during the early part of the investigation, soap solution made from a common soap was used as a flotation reagent. The froth obtained was a fairly good lime concentrate. This result was an important clue, and led to tests with the use of such reagents as oleic acid and sodium oleate. Later, cresol, creosote, coal tar and other similar flotation reagents were tested in combination with the oleic acid and soap solutions. As a result, oleic acid and cresol used together were found to be satisfactory.The tailing from the magnetic log-washer is in excellent physical condition fur flotation. The iron ore had been ground in a ball mill to 100 mesh for magnetic concentration. Hence the bond between the lime carbonate and the other constituents of the tailing was well broken."

Apr 1, 1926

By M. G. Pelipetz

High-pressure, high-temperature hydrogenation of coal has been known and practiced for many years. A full' understanding of the mechanism in this process by which coal is converted to oil and gas must rest on a critical interpretation of the manner in which external variables influence the rate and the course of the coal-hydrogenation reactions. Same Bureau of Mines studies on the effect of temperature, catalyst, and rank of coal on these reactions have been published. The effect of pressure was not studied in this earlier work, and the effect of reaction time was complicated by the interruption of long reaction periods in order to refill the autoclave with hydrogen. It is the purpose of this paper to present data from more recent autoclave experiments that extend the results of Storch, et al, on the kinetics of coal hydrogenation. These data must be explained by any comprehensive theory of coal hydrogenation; their detailed evaluation, however, will be deferred until a later publication.

Jan 1, 1949

By Richard J. Bielicki

Poor mixing of methane and air at coal mine working faces causes fluctuating methane concentrations. If these fluctuations are large enough, methane levels can periodically exceed safe limits, even though the time average methane concentration may be satisfactory. Concentration fluctuations measured underground can result both from variations in methane emission rate and poor mixing. The present paper reports on a statistical analysis of fluctuations at a constant methane emission rate, that is, on fluctuations due only to poor mixing. A full-scale model of a working face was used. Both peak heights and elapsed times between peaks were evaluated. Good mixing was indicated by normal, Poisson, and exponential distributions while poor or incomplete mixing was indicated by log-normal or gamma distributions.

Jan 1, 1974

By C. L. Chaney

Investigations were conducted to develop spectrochemical methods capable of determining 0.01 to 100 micrograms of metals in 50 milliliters of solution. The use of gallium hydroxide (Ga(OH)3) as a carrier-precipitant to concentrate metallic ions is described. A porous-cup graphite electrode is used to collect the precipitate. A specially designed plunger permits the electrode assembly to serve as the sample-containing electrode in the subsequent spec-trographic analysis. Analytical curves are presented for antimony, arsenic, beryllium, and zinc. Sensitivities of detection are given for 13 elements. The techniques were applied to identify impurities separated from tungsten, to determine trace impurities in solutions containing high concentrations of magnesium, cobalt, or nickel, and to identify trace impurities in hydrofluoric acid. Laboratory glassware was a serious source of contamination when low levels of zinc were determined.

Jan 1, 1963

By Steven M. Shope

The Bureau of Mines electromagnetic trapped miner location and communications system requires a thorough understanding of through-the-earth electromagnetic wave propagation. An earth model incorporating a magnetic dipole buried in a three-layered earth has been developed. The dipole source is located in the second subsurface layer. By application of proper limiting values, the three-layered model is reduced to two different two-layered models and eventually to the homogeneous half-space model. The solutions are in the form of infinite integrals. A numerical analysis was carried out and a computer program written to evaluate the surface magnetic fields. Numerical values for the magnet- ic field at the point above the source are presented in a variety of models.

Jan 1, 1982

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

By Fun-Den Wang

A new approach for evaluating pit slope stability by the limiting equilibrium method has been developed by the Bureau of Mines. The finite element method of plane strain analysis is used to find the stress field of the pit slope structure. This stress field is then used to find the normal and shear stresses along a potential failure surface. The normal stresses are used with the Coulomb equation to calculate the shear resistance. The shear stresses are integrated to determine the total driving force. The factor of safety is evaluated from the ratio of the resisting force to the driving force along a failure surface, and is found to be affected by the elastic material properties, modulus of elasticity, and Poisson's ratio.

Jan 1, 1970

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory conducted a study of laser safety in potentially flammable environments. Researchers measured threshold igniting powers as a function of beam diameter for butane and propane-air mixtures by laser-heating targets placed on optical fiber tips using a 1064 nm laser. The minimum igniting powers for propane-air and butane-air were about 250 and 300 mW, respectively. Threshold igniting powers for propane-air were approximately proportional to beam diameter for beam diameters from 0.1 to 2.0 mm. Results suggest that relatively powerful beams may be used in these atmospheres without causing ignition, provided the beam diameter is controlled. Threshold ignition delay times using 91125 and 62.51 125 pm fibers were approximately proportional to the inverse square of the laser power. Ignition delays were about 45 ms or longer for laser powers up to 800 mW. Preproduction samples of a commercial optical fuse prevented ignitions under selected test conditions. A self-healing effect was observed for one sample. Comparisons are made with the results of other researchers. O 2006 Laser Institute of America. Key words: propane ignition, butane ignition, laser ignition, nonbeam hazards, fiber optic fuse

May 3, 2006

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

Provide a method of detecting and locating miners trapped underground following a mine disaster. Approach Develop a surface deployed system which senses the vibrations caused by a trapped miner pounding on the roof of the mine and effectively determines the miner's location. How It Works If trapped underground, a miner would strike the roof of the mine with any implement at his disposal. This pounding causes vibrations in the ground which are transmitted to the surface where they are sensed by receiving transducers called geophones. Multiple geophones are positioned together for noise cancellation purposes in a form called a subarray. Seven

Jan 1, 1981

This Technical Memorandum Report is a collection of three working memoranda, prepared during the course of our work for the Bureau of Mines and bound together for convenient reference. These working memoranda present preliminary performance estimates, for baseband voice and narrow- band through-the-earth electromagnetic communications systems of principal interest to the Bureau, for operational/emergency mine communications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; and of theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau. The memoranda examine the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, up- link transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/meter (high) were used; for voice and narrowband, 10-1 for narrowband only. Examples of high, moderate, and low; surface and subsurface; harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 3, 1972

Develop a 22-ton capacity temporary mine roof support light enough to be easily lifted and transported manually from one place to another. Approach Several potential approaches were investigated in developing a new temporary support. An all-hydraulic, high-strength aluminum design was chosen as the best. The support was designed, fabricated, and tested in several mines. The first units, built for 6- to 8-foot seam heights, have a load- bearing capacity of 22 tons, and weigh only 55 pounds. How It Works The lightweight hydraulic support is designed for use in any temporary support situation in place of wood posts or steel mechanical or hydraulic supports. This includes use prior to roof bolting in room and pillar mining and in longwall development sections, use as head and tailgate supports for a longwall, and use as turn posts and breaker posts in retreat mining operations. The supports feature a release valve for quick manual extension to roof level, a lanyard

Jan 1, 1983

By A. W. Ambrose

"Records of individual wells form the basis for the successful operation of any company engaged in the production of petroleum. The expense attached to the compilation of records is negligible in comparison with the benefits resulting from their use. There a company has not a complete system of records, immediate attention should be given to the preparation of forms upon which to collect data, and, to the collection of data for these forms. The records needed vary with each district, but for each field a set should be adopted that will best meet the needs of each property. Practically all operators, and particularly all successful operators, agree on the necessity of good records, shopping what the wells have done, are doing, and may be expected to do in the future. Any operator realizes the value of records of sales of oil and should place almost equal emphasis on the records of well logs and histories showing the east and present performances of wells. Indeed, trustworthy records are absolutely necessary for the proper operation of any oil or gas property.Complete records should be kept on each well from the time the location and elevation are determined until the well is abandoned, and the engineer should review old records often enough to be familiar with the past performance of the various wells and with the conditions that affect production. Some of the forms that may be prepared are:--"

Mar 1, 1920

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997

By Edward F. Divers

A new nonclogging water spray system for continuous-mining machines has been developed under contract with the Bureau of Mines. This paper presents installation and operating guidelines for the system, which consists of improved and easily maintained machine-mounted hardware, including an inline Y-strainer, a hydrocyclone, a backup filter, and two quick-opening valves for flushing particulates from the strainer and hydrocyclone. Underground tests with continuous-mining machines have shown that when properly installed and maintained, the new sys tern virtually eliminates nozzle clogging and thus greatly reduces spray maintenance. The sys tern is relatively inexpensive and has been installed on typical continuous-mining machines for a total cost under $1,000.

Jan 1, 1976