Search Documents

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

To devise an economical, environmentally acceptable method for recycling scrap lead-acid batteries. Approach A combination electrorefining-electrowinning method for recycling lead metal and sludge from scrap batteries was devised which produces a 99.99 + percent pure lead product and eliminates the lead and sulfur oxide emissions that are the normal by-products of high-temperature smelting processes. How the Method Works Lead metal grids and lugs are separated from the battery sludge by washing and screening, and are melted and cast into anodes for electrorefining by the Betts process. The electrolyte used is fluosilicic acid, a large volume waste product generated during the production of phosphate fertilizer. During the electrorefining process, impurities in the anode are trapped and held in an adherent slime blanket on the surface as the anode dissolves while pure metallic lead is deposited on a lead cathode. The major problem in the past has been to recover the lead from the battery sludge which consists of approximately 60 percent lead sulfate, 21 percent lead, and 19 per-cent lead dioxide. In the flow sheet developed by the Bureau

Jan 1, 1983

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines' horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau's methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

The Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining (hereafter referred to as the Panel or the TSP) was established by Section 11 of the Mine Improvement and New Emergency Response Act of 2006 (MINER Act). The Panel was charged with providing “independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant properties of belt materials in underground coal mining.” The TSP was impaneled by the Honorable Elaine L. Chao and commenced its work on January 9, 2007. At this first meeting, Mr. Richard E. Stickler, Assistant Secretary of Labor for Mine Safety and Health, asked the Panel to report on many issues including how recent technological advances could be applied to atmospheric monitoring systems, point-type heat sensors, current state of fire-resistant vs. fireproof belt materials, and belt fire suppression systems to improve miner safety. In addition, Mr. Stickler asked the Panel to review belt air velocity limitations. The Panel members attended 12 days of public meetings over a nine-month period. Three of the public meetings were scheduled for the Panel to hear from technical experts and those persons or organizations interested in providing input. The meetings were held in Coraopolis, Pennsylvania with emphasis on belt fires, belt maintenance, belt flammability and toxicity, ventilation, and escape issues; in Salt Lake City with emphasis on ground control and convergence issues; and in Birmingham with emphasis on fire detection, sensors and atmospheric monitoring systems. National Institute for Occupational Safety and Health (NIOSH) researchers, Mine Safety and Health Administration (MSHA) personnel, representatives of the major belt conveyor manufacturers and a representative of the National Mining Association provided discussions at the Coraopolis meeting. In Salt Lake City, Utah, MSHA district managers and ventilation specialists, a member of the Aracoma Mine No. 1 investigation team, a representative of the Bureau of Land Management, and industry and consulting representatives of the Utah Mining Association and the Colorado Mining Association made presentations. In Birmingham, Alabama, atmospheric monitoring system representatives, NIOSH researchers, representatives of coal mining companies, and UMWA workers from two Alabama mining companies made presentations. In addition, a staff member of The Center for Regulatory Effectiveness also presented comments to the Panel. In conjunction with the meetings in Salt Lake City and Birmingham, three-member subcommittees of the Technical Study Panel made field visits to the Skyline Mine, the Aberdeen Mine, and the Jim Walter Resources Mine No. 4. The mine visits were scheduled to see first-hand the mining conditions under which belt air was being utilized as an additional source of intake air for working sections.

By ROBERT R. ROUGH, FRANK L. BACON, John Dasher

(being shipped as bailast in ocean freighters). Within the last 10 years it has become more economical to use local sands, and there has been a general shift from the Belgian sand. Deposits of purer sand were treated and used for 'some time: but the suprly became limited, and means were sought to beneficiate the more bountiful subpay-f impure beach sands. These sands are composed of, 50 percent feldspar and 50 percent quartz, with small amounts of iron- bearing minerals, The most objectionable impurities in these West coast sands are the oxides of iron and aluminum. The Del Monte (Calif.) beach sand contains about 0.13 percent FeqQg and about 11.0 percent Aig03 (the latter being furnished by the large amount of feldspar present.) For the manufacture of feldspar present.) For the manufacture of flint-glass containers the maximuni quantities of these two impurities permitted in the sand are 0.05 percent F20 and 6 to 8 percent A1203.. The Fe0g occurs in the sand as follows: Traces of iron-bearing minerais resistant to weathering, ferruginous clay stains on the sand grains, and iron minerais not visible and possibly in solid solution or as colloidal incisions in the grains of feidspar or quartz. A good part of the iron in the sand is present in the traces of iron-bearing minerals, biotite, ilmenite, garnet, monazite; and hornblende. Biotite is present in larger quantities than the others. Samples of quartz, were freed of iron-bearing minerais by the use of heavy liquid (sp.gr. 2.70), leached with boiling HCI and SnCl2. Under a microscope a few apparently clean quartz grains were selected, and Fe203 was determined spectrographically to be 0.03 percent. The technique is similar to that described by Gabriel and Slavin. 4/

Dec 1, 1943

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

Develop a safer, more effective, and more efficient method to control fires in abandoned coal mines and waste banks. Maintain the costs of this new method at less than or comparable to conventional AMI fire control methods. How It Works Cryogenic extinguishment of subsurface fires is a method of heat transfer. Bureau-designed injection equipment produces a pumpable slurry of liquid nitrogen and solid particles of carbon dioxide. Liquid or gaseous carbon dioxide from a pressurized tank flows to a bell-shaped nozzle where the change in pressure causes the carbon dioxide to form a granular snow. The solid carbon dioxide is mixed with liquid nitrogen. A jet pump is used to move the slurry through the delivery lines and into a simple injection probe. At injection, the nitrogen vaporizes and the carbon dioxide sublimes. This phase change produces a cold gas (-180° C) that, as it expands and moves in all directions, removes heat and also displaces oxygen. This combined process inhibits the combustion process and lowers the temperature below the reignition point. When the liquid nitrogen and solid carbon dioxide are converted to gases, the expanding gas acts like a piston, forcing warm air out of the porous bed, Although smoke and hot gases arc forced from the burning coal, generally there is no significant increase in the odor associated with burning coal.

Jan 1, 1992

Reduce workers' dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the boom of a continuous miner at the conveyor throat. Dusty air from the face area is drawn through the scrubber and cleaned air discharged into the return. How it Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator and contaminated air behind the line curtain to the return. The problem with exhaust ventilation is that the line curtain should be within 10 ft of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back towards the operator. An effective way of removing this dust is with a scrubber mounted on the mining machine.

Jan 1, 1988

By O. C. Baptist

The gravitational pressure gradient (GPG) in porous sandstone containing free gas was determined to define the proper GPG to use when calculating the rate of downdip flow of oil in the Sub-Scalez No, 1 sand, Elk Hills field, Naval Petroleum Reserve 1. The GPG was determined at several gas saturations using long, artificially consolidated sandstone models that were mounted vertically in some tests and horizontally, with rotation, in others. Also determined by laboratory and field tests were relative permeabilities, capillary pressure relations; critical gas saturation, water sensitivity, and depletion drive performance. The critical gas saturation in the models having an absolute permeability of 1 to 2 darcys was about 2 percent of pore volume. The GPG with the critcal gas saturation was that due to the weight of the gas-saturated oil. The GPG in the upper part of the models was reduced as gas saturation increased to a value considerably larger than the critical. The exact gas saturation at which the GPG became less than that due to the weight of the oil could not be determined but was estimated to be of the order of 10 percent of pore volume. Tests indicate that the rate of oil production is not permanently reduced by exposure of the sand to fresh water but that the rate of injection of fresh water will be considerably less than that to brine, Methods for determining the factors mentioned above are discussed.

Jan 1, 1967

Control dust generated during mining in salt mines. Approach A machine-mounted exhaust ventilation system which moves with the cutting machine from place to place was developed. The system captures the dust at the face of the heading and exhausts it downstream of the heading in the crosscut. This helps cause fresh air from the crosscut to flow over the machine operator's position, and aids in keeping the dust cloud close to the face. How It Works The system consists of (1) a circular intake hood with a 10-inch slot extending 250 degrees around the base, bolted to the gearhead; (2) 20-inch-diameter wire-wound flexible ducting to connect the intake hood to the fan (25 ft. is allowed sufficient slack for bar movement); (3) an industrial exhaust fan capable of generating 10,000 cfm with 13 inches water gage pressure at 1435 rpm; and (4) 150 ft. of collapsible 24-inch tubing for the exhaust duct which is de-played and returned In each heading by the cutter operator and/or his helper.

Jan 1, 1983

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

By M. J. Kovalik

Illinois No.6, a high-volatile B coal of low fluidity, was blended with fluidized-bed char and coke breeze to improve the strength of the coke obtained from carbonizing this coal. Twenty-one tests, selected from those made in the small-scale Hanson carbonizer, were carbonized in the BM-AGA 13-inch-diameter, cylindrical retort, with a coal charge of about 90 pounds; the strength of the cokes was determined by the standard ASTM tumbler test. Using the same procedure, 10 tests were made with High Splint, a high-volatile A coal from Harlan County, Ky. Carbonization of the blends produced larger and stronger cokes than did the Illinois No.6 coal singly. The optimum blend contained 6 percent each of char and coke breeze. Further improvement in coke strength was realized by either preheating this blend prior to carbonization or by adding a small pro-portion of a premium blending coal. The former method could possibly eliminate the use of premium coking coals in blends with Illinois No. 6 coal to make an acceptable metallurgical coke. Except for no improvement in coke strength by preheating, results for High Splint coal showed behavior similar to that of the Illinois No.6 coal.

Jan 1, 1973

By Clarence O. Babcock

This Bureau of Mines report presents the initial development of a two-dimensional method of analysis for inclusions in plates in which the deformed shape of an open hole and the separate structural behavior of inclusion and plate with hole are used to obtain the stresses and strains in the inclusion only. In this report the solution for a circular inclusion is presented because a direct verification of the results with previous solutions was possible. The numerical results were in exact agreement with those obtained with the equations of Sezawa and Donnell. The equations developed are less complex than those of Sezawa and more general, for a circular inclusion, than those of Donnell. Stresses and strains in the inclusion are in terms of the elastic constants of the inclusion and the plate and the biaxial stress field applied far away. The elastic constants can be all different. An important conclusion from this work is that a difference in Poisson's ratios between inclusion and plate may be as important as a difference in Young's moduli between inclusion and plate in producing the inclusion effect. Many problems in mining and rock mechanics can be treated as inclusion problems. The understanding of inclusion behavior on a physical basis should provide the solutions to some of these problems.

Jan 1, 1974

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

Prevent the explosion of methane gas or coal dust by replacing air with inert gas inside highwall mine excavations. Approach Use combustion gases as a source of inert gas with low oxygen content to blanket the cutting, head of highwall mining machines. This gas is placed strategically at the collar of the excavation where it enters the hole to replace the mined coal volume. The elimination of oxygen from the hole prevents explosions of gas or dust. How It Works Highwall mining methods arc used when surface mining becomes uneconomical. One method of highwall mining involves use of a horizontal auger to enter the coalbed from a surface mine bench. The coal is mined in a series of horizontal, parallel, and large-diameter holes. Historically, little methane has been associated with auger mining. However, mining technology has extended the reach of auger mining, which can increase the occurrence of methane. Methane explosions at auger mining operations have been increasing. Methane has been the primary fuel source of these ignitions, but coal dust also may have been involved.

Jan 1, 1993

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947

Decrease the dust concentrations at the shearer and reduce downtime associated with spray system maintenance. Approach Increase the quantity and quality of the water supply on longwall faces by decreasing pressure losses, Increasing pump capacity, and installing a "non-clogging" filtration system. How It Works Water sprays and ventilation are two of the primary methods of dust control on longwall operations. Increasing the quantity and quality of the water supply to spray systems is one of the more effective and least costly dust control methods that operators have at their disposal, yet this method is largely ignored. Poorly positioned spray nozzles operating at low pressures (and flows) which plug frequently cannot be effective. Water supply system Improvements should be a fundamental part of all longwall dust control plans. Upgrading a water supply system may require one or more of the following improvements depending upon where a particular system may be deficient: Increasing pump capacity for additional flow and pressure; increasing line sizes to decrease pressure losses: and, decreasing maintenance downtime and Improving water quality by installing a "non-clogging" filtration system.

Jan 1, 1981