Search Documents

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

Improve surface mine haul-age truck safety and efficiency by providing a means for sensing the weight and distribution of the truck's load. Approach The safety hazards and the economic implications of overloading mine-haulage trucks were analyzed to determine the net effect of that practice on mine operations. The analysis indicated that: Ten to 25 pct overloading is typical; Higher haulage, tire, and maintenance costs occur due to overloading (a 20 pct overload was estimated to increase operating costs 7 pct per ton); Ten to 15 pct of haulage? truck injuries and fatalities are attributable to overload conditions, at a cost over one million dollars per year to the mining industry. Vehicle-weighing technology that conformed to the performance specification for an off-highway haulage truck overload detection system was selected for in-mine testing. How It Works Normally, volumetric estimates are made during the loading sequence which do not account for the varying ore density. Hence, the actual weight of a load is never precisely known. By providing a precise measurement, an overload detection system will not only indicate vehicle overloading, but will also show under-utilization of the truck. One system tested by the Bureau of Mines was the ?Load Analyzer" manufactured by Pactronics Corporation in California. This system consists of a meter-type analog readout for the cab console and three "Electrosensors" (linear variable differential transformers) attached to the main frame. Using conventional welding and brazing techniques, two sensors are attached between the front members of the engine sub-frame and the top of the left and right trailing arms (one sensor per arm). The same techniques are used to attach the third sensor to the rear centerline of the truck. between the main frame cross member and the A-frame. The readout unit on the cab console indicates by color-coding whether each sensor loading is under (green), at (yellow), or over (red) the pre-set rated load. The three-sensor configuration with in-dependent readouts also detects uneven distribution of the load.

Jan 1, 1984

By W. E. Robinson

Sixty samples, selected from a 2,300-foot core of the Green River Formation in Colorado, were studied to ascertain differences in the structure of the organic material present in the oil shale samples. Emphasis was placed upon relating differences in the aromatic content of the insoluble kerogen and the alkane content of the extractable material obtained from the selected samples. The methods used in determining these differences consisted of fractionation of the soluble material, carbon and hydrogen analysis, volatile material determination, carbon residue determination, oxidation rate determination, and infrared analysis. In general, it was concluded that the organic material in this core does vary in chemical structure and that same of these variations resulted from factors related to depth of burial. Other observed changes in structure of the organic material were not depth-dependent and resulted from other factors such as source material variations, biological alterations, or ecological differences.

Jan 1, 1971

By A. L. Engel

Many western ores containing ;old, silver, and copper can be mined and concentrated at a profit only when the recovery of those metals is high and treatment costs are low. Usually, ores containing easily dissolved copper minerals, or copper minerals that become soluble to some extent through oxidation during treatment, present a real problem in cyanidation. Copper cyanide compounds are formed that tend to 'precipitate and that cannot yield regenerated cyanide and metallic copper on contact with zinc. This results not only in some loss of copper through solution in cyanide, but in excessive consumption of cyanide above the amount required for the extraction of Gold and silver. Any moans, therefore, of minimizing the: loss of cyanide while at the same time effecting high recoveries of the several values contained in the ore is of wide interest. A sample of typical low-grade ore of gold, silver, and copper, containing copper-sulfide minerals, was obtained from the MacLaren Gold Mines Co., Cooke, Park County, Mont., for laboratory investigation by flotation and cyanidation.

Jan 1, 1950

By Robert M. Becker

A thick-wall cylinder solution applicable to the evaluation of anisotropic elastic parameters is derived for the interpretation of stress relief data. For a restricted class of problems, a special relationship among certain orthotropic moduli yields stress distributions for the plane orthotropic problem that are identical to the corresponding isotropic case. A ring or hollow cylinder with these specialized anisotropic properties subjected to uniform radial loads is one of the problems in this class. Consequently, known stress solutions are used to develop the strains and displacements for a specialized orthotropic thick-wall cylinder under uniform pressures. The results are consistent with anisotropic equations used in the evaluation of in situ rock stresses.

Jan 1, 1968

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986

By M. A. Schellhardt

"INTRODUCTION The augmented demands for natural gas in many parts of the United States as a result of war have increased the need for information regarding the producing characteristics of natural-gas and gas-condensate-type wells capable of delivering large volumes of gas, as such information is important to the formulation of conservative and efficient operative and recovery practices.,For many years, the capacity of natural-gas wells to produce gas has received studied consideration by Bureau of Mines' engineers, and three reports 3/ on gaging gas-well capacities have been published. In Report of Investigations 2929, Pierce and Rawlins point out that for accurate gaging, the actual pressures at the face of the sand in the well and the relationship between such pressures and the rates of flow of gas through the sand must be determined. Their report describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the wellhead.In Report of Investigations 2930, Pierce and Rawlins explain how the fundamental relation"

Aug 1, 1944

By John C. Edwards

A two-dimensional, time-dependent, mathematical model has been developed that describes fire spread along the walls of a ventilated duct. The model is based on the assumption that the leading edge of the fire zone propagating along the wall surface coincides with the isotherm for the fuel ignition temperature. The model includes gas-phase energy transport via radiation and forced convection inside the duct and solid-phase energy transport by conduction into the fuel lining. Product gases emitted from the fire zone are assumed to mix uniformly with the ventilation gas to produce an optically dense gas mixture at the combustion temperature that enters the preheat region. Numerical solutions of the model equations for a coal-lined duct (simulated coal mine entry) have been used to investigate the effects of tube radius, air velocity, combustion temperature, and optical density of the soot-laden gas upon the terminal fire spread rate.

Jan 1, 1977

"As stated earlier the primary goal of the Generic Mineral Technology Center for Respirable Dust is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. While initial work was directed to coal dust the charge to the dust center has been expanded to include diesel particulates and asbestosis, the latter of deep concern not just to workers in the mineral sector of the economy but also to the general populace.A major facet of Dust Center research has been the analysis and documentation of comprehensive research protocol and procedures that are appropriate state-of-the-art in the various areas of respirable dust. In addition to definition of standardized research protocols and procedures which would be utilized by center personnel for uniformity and reproducability there is a considerable need for utilizing standardized respirable dusts in experiments with consistent, reproducible characteristics which simulate those of actual mine dust. This respirable dust needs to be available in large quantities for a wide variety of research uses that include animal and medical experiments. The dust must be free of the lubricating oils and grinding wheel contaminants that are frequently encountered in laboratory generated dusts.The holistic approach to establishing standardized protocols and procedures applicable to the five major research areas of the center is presented in Figure 5.In one hypothesis, range in coal volatility is considered to be a major causal factor in the incidence and severity of pneumoconiosis. Therefore a suite of characterized standard respirable dust samples have been prepared for researchers from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz, limestone (rockdust) and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared.A suite of medical investigations have been developed utilizing small and medium size animals as well as non-human primates in a variety of dust/lung interaction projects which will be discussed in the next section. A number of respirable dust sampling and dust generation methods have been investigated and selected techniques utilized for both in-mine and in-laboratory research investigations. These will also be discussed in more detail later. A wide range of respirable dust size, chemical and mineralogical analyses have been investigated, standardized and documented for use in various research investigations.This interaction and documentation of various respirable dust sample procedures, animal and medical tests, sampling and dust generation methods, plus size, chemical and minerological analysis applied in the five major areas of research investigation have served to create a very favorable synergism and rapid technology transfer in the respirable dust center."

Jan 1, 1988

By R. Van A. Mills

[In previous contributions** the writer has called attention to important relations that faulting bears to the migration and accumulation of oil end gas. It has been pointed that favorably situated parts of oil and gas bearing, sands have been enriched by migration art segregation incident to faulting. The escape of water through natural passages such. as fault fissures has induced wide spread hydraulic currents through the beds toward these, points, of diminished pressure and these water currents, plus buoyancy hove contributed largely toward the migration of oil to favorable rock entrapments in the vicinity of the faults.*** The propulsive force of expanding gas has been one of the contributing causes for the hydraulic currents. Paradoxical as it may seem, the escape of gas with entrained oil through fissures has been on important factor In the migration, and accumulation of oil in many faulted areas. Compressed gas is the propulsive force by which oil generally moves to producing wells. It is also one of the propulsive forces by which oil has moved with or even ahead of water under conditions: of differential pressure brought about by faulting.]

Jan 1, 1922

By N. F. Le Jeuns

For a number of years the Bureau of Mines has conducted semi-annual surveys to determine the changes in motor gasoline being sold in the United States. It was pointed out in the previous survey that there was an apparent tendency toward greater uniformity in the character of gasoline marketed in the United States. This practically uniform tendency which continued from April, 1917 to January, 1923, has been interrupted in the, present survey, as shown by an examination of the column marked "Difference," as given in Table 1. The figures in this table were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10% ,(85 samples) having the highest end points and the 10% having the lowest end points mere grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10%" and the ?Minimum 10%? respectively. The same process was used on the other surveys.

Jan 1, 1923

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962

Enable mine personnel to determine the effectiveness of and to optimize the mine fire stench warning system without resorting to costly trial and error fire drills. Approach The mine fire stench warning system is used by underground metal/nonmetal mines to warn mine workers of a fire or other emergency. Stench is released directly into the mine ventilation and/or compressed air lines, and its repulsive odor warns miners to evacuate the mine or to follow other established emergency procedures. Unfortunately, since most deep metal mines have complex ventilation systems, some areas of the mine may receive nauseatingly high concentrations of stench while other areas, in more remote locations, may receive no warning or greatly delayed warring at best. The Bureau of Mines, through research, endeavored to solve this problem with a computer modeling system designed to calculate the distribution of odorant by the stench warning system.

Jan 1, 1986

By Ronald D. Hill, Elmore C. Grim

The cost of reclamation can vary widely, depending on the primary objectives of the restoration activities. statistics in this study originated from State files, publications, and personal communications relating to restoration and pollution control measures for previously mined lands (orphan lands) and active mines. Reclamation of orphan lands is generally considered a public burden and constitutes an economic problem. All work reported here was completed under government contract, by the lowest bidder, with money coming from State and/or Federal funds. Cost would have been substantially lower had the reclamation been concurrent with mining. Several persons connected with some of the projects have observed that costs could probably be reduced by at least one half, if the reclamation had been conducted along with the mining. The expense of clearing and grubbing of volunteer vegetation, disposal of buried trees and brush, loosing of compacted spoil, and re-establishing access to areas could be saved. In addition, a contracting firm doing the work for a government agency would have mobilization costs and receive a profit. Mining companies also are profit conscious and would consider these costs in anticipating their profits (e.g., overhead would be less if reclamation is integrated with mining). The data presented here should serve as a guide for estimating and determining cost ranges, however, it should be recognized that variations exist. Adjustments may be necessary from the standpoint of physical conditions, economic conditions, price changes, and more restrictive requirements of recent surface mining laws. Reclamation conditions, procedures and successes in the eastern United States, particularly in Appalachia, have no bearing on conditions to be expected in the western United States. The situations are wholly different. Reclamation in the West differs from th t in the East, primarily because of aridity especially a during the summer months 1). Because of the many variables and differences between reclamation in eastern and western areas, they will be discussed separately.

Jan 1, 1974

By H. H. Schrenk, L. B. Berger

"INTRODUCTION The Bureau of Mines frequently receives requests for information and advice regarding the equipment necessary for establishing laboratories for the analysis of mine atmospheres. Such requests are made by mining companies, State mining departments, and other agencies concerned with the safety of mining operations. In many instances it is desired to install a complete laboratory, which will necessitate purchase of suitable gas-analysis apparatus and all the minor but important accessory equipment needed to carry on this type of work. Although publications that describe methods and techniques applicable to the analysis of mine atmospheres are available, it is not within the scope of such publications to give detailed information on laboratory equipment or design. Persons unfamiliar with laboratory practices and gas-analysis procedures may find it difficult to decide upon the proper equipment for their particular needs and to itemize the various accessories that must be obtained to set up a complete laboratory.The purpose of this circular is to discuss the different types of equipment that may be used in the analysis of mine atmospheres, with particular regard to the application and limitations of each type. Information on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres is given also, and suggestions on laboratory design are included. As much of the necessary equipment may be obtained from laboratory supply houses, the information should aid in arriving at estimates of the cost of proposed laboratories.The procedures involved in the analysis of mine atmospheres are not described; such information is contained in publications referred to in this circular."

Feb 1, 1948