Search Documents

By James E. Mills

Coal, in the process of mining, transportation, and handling and on exposure to the weather, is subject to more or less disintegration. This disintegrated coal is usually called "slack" and amounts often to a considerable percentage of the lump coal produced in the mines. If this slack coal is wasted the loss so occasioned ranges from 5 to 50 per cent, or even more, of the total coal mined. It is therefore clear that the utilization of this waste slack coal becomes a serious economic consideration. When the coal is suitable for the production of coke, the utilization of the slack presents no difficulty, as it is in demand for that purpose. If the coal does not produce good coke, but cakes rather readily, the slack can be used for boiler purposes, as it fuses together more or less quickly, and burns on the furnace grate without great loss. Coal that cakes less readily can be burned on grates of special construc- tion. When so used it is more troublesome to handle, and the waste is greater than when lump coal is used. Consequently the price of much of the slack coal for fuel purposes ranges considerably lower than that of the lump coal from the same mine. The full value of this slack coal as fuel can be realized by first form- ing the coal into a coherent mass or briquet, such briquets, when of good quality, being equal to or of greater value than the original

Jan 1, 1911

By Lloyd A. Morley, Alan M. Christman

Presented below is a review of how the objectives, as outlined in the statement of the problem, were achieved. 1. Methods of evaluating the performance of grounding systems must be described. These methods are the subject of Chapter III. 2. Field trips to operating mines should be undertaken, and a cri¬tique of their grounding systems made upon the basis of obser¬vation and the application of the above techniques. An analysis of field trip data, along with practical recommendations, is in¬cluded in Chapter IV, while a complete review of all field trips is given in Appendix I. 3. Because of their thoroughness, present coal mine regulations should be evaluated, and their applicability to open-pit environ¬ments appraised. This has been done in consultation with governmental agency, manufacturing, operating mine, and consult¬ing engineers. As stated in Chapter IV, insight gained through field observations has served to amplify and extend the base of knowledge from which the recommendations were made. 4. The results of these investigations should lead to suggested Federal standards. Such recommendations comprise Appendix II. In addition, several important factors, which are discussed in Chapter IV, were brought to light as a direct result of the field research. 5. Seasonal variations in the earth resistance of ground mats, as illustrated by Table 12, reinforce the need for periodic

Jan 1, 1976

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Accidents occur when least expected, from sources that we rarely anticipate and with outcomes that can vary greatly. Anyone who has ever been involved in an automobile accident knows, the transition from driving comfortably and safely down a highway to being involved in a potentially life-threatening situation can occur in a heartbeat. Accidents on the job are no different. The mining industry has a relatively small number of electrical injuries, compared to industries such as construction or agriculture, due to the small total employment in mining. Mining does, however, have one of the highest occupational electrocution rates of any U.S. industry, at 2.8 for every 100,000 workers per year. This is approximately four times the average for all industries. Data from the Mine Safety and Health Administration (MSHA) shows that 75 electrical fatalities occurred in the mining industry between 1990 and 1999. Of these, at least 17% involved high-reaching mobile equipment that contacted overhead power lines.

The Federal Mine Safety and Health Act of 1977* defines respirable dust as dust measured with a device approved by the Secretary of Labor and the Secretary of Health and Human Services [30 USC 842(e)]. The approved sampler for respirable coal mine dust is the coal mine dust personal sampler unit (CPSU) [30 CFR 74; Jacobson 1971; Jacobson and Lamonica 1969]. The CPSU is generally called the 10-mm nylon cyclone, although the 10-mm nylon cyclone is actually just one component of the CPSU. The CPSU may either be mounted on a worker (with the sampling head positioned in the breathing zone for personal exposure monitoring) or in a fixed location for area sampling [Tomb 1990]. The CPSU consists of a pump unit, a sampling head assembly, and a battery charger if rechargeable batteries are used in the pump unit [30 CFR 74.2]. The sampling head assembly contains two stages. The first stage is a 10-mm nylon cyclone, which has collection characteristics similar to an elutriator. The amount of dust penetration depends on the flow rate [Jacobson and Lamonica 1969]. The second stage is a membrane filter (vinyl, pore size 5 pm) that collects the dust passing through the cyclone. The dust collected on the membrane filter is weighed to a precision (standard deviation) of 81 pg [Parobeck et al. 1981], and the respirable dust concentration in the mine atmosphere is then determined from the mass of dust collected and the volume of air sampled [Tomb 1990].

Jan 1, 1997

By Daniel Edelstein

The supply of arsenic trioxide in 1982 was adequate to meet domestic demand. Allocation of supply by major domestic and foreign producers that began in 1977 ended during the first quarter of 1982. Major demand was about evenly divided between industrial chemicals and agricultural chemicals. Domestic Data Coverage.-Commercial- grade arsenic trioxide and arsenic metal were produced by only one U.S. company. In order to prevent disclosure of proprietary data, arsenic production data have been withheld.

Jan 1, 1983

By David Gearhart, Thomas Barczak

Hydraulic cylinders a re used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support systems operate at pressures as high as 7,000 psi to provide the necessary support capacities. Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performance characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control. This paper examines the basic operating principles of state-of-the-art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (S) hydraulic failure mechanisms and how to detect them

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Abstract—Overhead electric power lines present a serious electrocution hazard to personnel in a variety of industries. Overhead lines, typically uninsulated conductors supported on towers or poles, are the most common means of electric power transmission and distribution, and are exposed to contact by mobile equipment such as cranes and trucks. Equipment contacting energized overhead lines becomes elevated to a high voltage, and simultaneous contact by personnel of the “hot” frame and ground can cause serious electrical shock and burns. Industries where risk of these accidents is greatest include construction, mining, agriculture, and communications/public utilities. An estimated 2300 accidental overhead line contacts occur each year in the U.S. This paper describes a practical low-cost concept to detect actual contact of mobile equipment with a high-voltage line and provide a warning. Accident statistics indicate that more than half of the fatalities could be prevented by such a device. Index Terms—Crane, electrical shock prevention, engineering control, mining, mobile equipment, power line.

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By Douglas C. Peters, Valois R. Shea-Albin, Dennis R. Dolinar

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq's equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 1992

By T. R. Taubert, D. H. Carlson, J. H. Johnson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO, NO, and NO, at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory- grade instruments. Concentrations of CO and CO, measured by the EMA were usually within + 14 pct of concentrations measured by laboratory-grade instruments for CO and 220 pct for CO,. EMA- measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO, differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1992

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster-Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 2010

By Philip W. Holland

The U.S. Bureau of Mines has designed and built an inexpensive, weatherproof, temperature-controlled cabinet to provide temporary housing for analytical instrumentation. The cabinet consists of an inverted Styrofoam ice chest, an electric fan for air circulation, and a proportional temperature controller equipped with a thermistor sensor and a light bulb as the heater. The cabinet provides a constant-temperature environment for a moisture analyzer and a strip chart recorder when outside temperatures range from -SO to 21° c.

Jan 1, 1993

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971