Search Documents

By Steven J. Page, John A. Organiscak

Prolonged exposure to airborne respirable coal mine dust is responsible for coal workers' pneumoconi¬osis (CWP): Furthermore, miners who show evidence of higher radiographic categories of simple CWP are at increased risk of developing progressive massive fibro¬sis (PMF). As of 1990, there were nearly 130,000 coal miners in the United States. "' This excludes mines that produce less than 10,000 tons annually and the anthracite coal mines. Estimates indicate that at age 58, an average of 7/1000 U.S. workers and 89/1000 U.K workers will have developed PMF(2-1) Health research studies have iden¬tified that the risk of developing and the severity of CWP arc directly related to (1) the amount of respirable dust exposure and (2) the coal rank.,'- The rank of coal is its stage of formation in the series peat, lignite, sub-bituminous, bituminous, and anthra¬cite (in order of increasing rank). The rank of coal can also be represented by the com¬mercially important characteristics specified by its proximate analysis: fixed carbon, vol¬atile matter, mineral matter, and moisture content.

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

Wires leading to or from underground facilities can develop hazardous voltages because of lightning exposure. The locations of many mine portals are particularly susceptible to lightning effects. The application of protective devices to limit this potential danger is necessary.

Jan 1, 1975

By A. C. Watts, C. A. Allen

In the No. 3 Sunnyside mine of the Utah Fuel Co. a disastrous fire started on the afternoon of August 17 , 1920 , the effects of which are still present in the mine . On account of the extent of the fire , the expense involved in reopening the mine and the opportunities afforded for determining the effects of depleted air , a description of it is worthy of record . This paper is a summary of a more complete report , prepared by the writers , which will be published by the U. S. Bureau of Mines .

Feb 1, 1922

By D. J. Parker

State governments are increasing their efforts each year toward promoting the safety of miners .. Accidents underground are being avoided and mines made safer by means of revising and adding to their mining laws , by enforcing them through mine inspection departments , and by hearty co - operation with other agencies working miners ' safety . The U. S. Bureau of Mines is glad to testify to the co -operation that it receives from State mining departments in its safety work ; reports of the field mining engineers of the Bureau bear witness almost daily to the efforts of the States toward safety in mining . * This Through the courtesy of Mr. William Ogilvie , District State Wine Inspector of District No. 2 , with headquarters at "cAlester , Oklahoma, the Bureau has been furnished with a copy of a letter sent to various mining companies of Mr. Ogilvie's district in Oklahoma, relative to safety in Oklahoma mines . letter shows both the vigorous efforts which the State of Oklahoma is making toward increased safety in mines , and the recognized value of the types of electric cap lamps approved by the U. S. Bureau of Mines as " permissible " for use in gaseous mines ; it is accordingly reproduced in part : "hen during my first inspections of several coal mines in the district I found gas , or fire- darp being given off more or less constantly from the freshly cut coal at numerous points throughout the mines , I became uneasy relative to safety conditions , and am still considering your safety from many angles , but I am more concerned about the gas given off and the coal dust produced daily, than any other factor at the present time .

Jun 1, 1922

By Walter R. Storms, Jerry W. FAUST

This paper, which describes mining methods and costs at the Kearney zinc-lead mine, is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices, methods, and costs in varicus mining districts of the United States. The Kearney mine, which is owned by the New Mexico Consolidated Mining Co., a subsidiary of the Peru Mining Co. (Illinois Zinc), is situated a few miles southeast of the town of Hanover, in the northwest corner of sec. 27, T. 17 S., R. 12 W., in the Central Mining District, Grant County, N. Mex. (Figs. 1 and 2.) This report presents a brief history of the district, describes the geology, and outlines methods of prospecting and exploration, including eampling and estimation of tonnages and values. Development and mining methods are explained, and transportation, ventilation, drainage, safety measures, and organizatich are described. The wage scale and mining costs comprise the concluding sections of the report.

Jun 1, 1949

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By Ralph L. Brown

The chemical properties of the unsaturated members of the aliphatic series of hydrocarbons are such as to render them " made to order" starting points or basic . materials for the synthesis of hundreds of important organic chemicals . The tremendous quantities of these unsaturated compounds that are being produced daily in the various coal carbonization and oil refining processes , and which at present have little value other than that of fuel , render a survey of the identity and ex- tent of occurrence of these compounds important from the viewpoint of economic utilization and resource conservation The increased need of liquid fuel and the relatively early exhaustion of petroleum resources will eventually require every utilization of liquid fuel products obtainable directly or indirectly from coal . Accordingly , the Bureau of Mines took advantage of an opportunity for examining the gaseous unsaturated hydrocarbons found in the gas obtained when a mixture of water- Collection of the material gas tar and coal is distilled in a gas-making retort . for examination was made possible through the courtesy of the Trent Process Corporation , Washington , D.C. , which was at that time carrying on at the Georgetown Gas Works , distillation of " amal gams " prepared from various coals and oils by the Trent process for cleaning coals . Kanawha gas coal ( 70%) and water gas tar ( 30 % ) from the Washington Gas Light plant were used in the " amal gam" being distilled at that time . The results obtained in this examination are presented here .

Feb 2, 1922

By Earl C. Lane

The Bureau of Mines is making a survey of petroleum products manufactured on the Pacific Coast from California crude oils . California crude petroleum is known to differ in some characteristics from the crude oil produced in other parts of the United States , and the claim has been made that the present Federal specifications are unduly severe when applied to the products made from California crudes . The main purpose of the present survey is to determine whether these claims are justified . This report deals only with California gasolines . Other products , such as burning oil , fuel and lubricating oils , will be taken up later . The samples reported were furnished in most cases , by the four large refining companies located on the Pacific Coast , although a number of samples of motor gasoline were purchased in the open market . In Los Angeles , samples of motor gasoline were obtained from service stations representing as many different refineries as possible . Inasmuch as San Francisco is one of the cities covered by the regular semi -annual motor gasoline survey conducted by the Bureau of Mines , it was not considered essential that the set of samples obtained from this city be as comprehensive as would otherwise have been necessary . The gasoline consumed in the States of Washington and Oregon is furnished for the most part by California refineries , and no effort was made to procure samples from these States .

Apr 1, 1922

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By L. C. IlsLey

A specially recommended cable is a rubber-sheathed cable that has met the minimum performance requirements for cables as set forth in Schedule 20. The first in the series of recommended cables was listed September, 1930, by an ad- vance notice published as Information Circular 6375 which described the conditions under which the cable tests were made. Since that time six additional cables have met the test re- quirements and have been specially recommended. The complete list of specially recommended. cables is as follows: Specially recommended-cables Cable Symbol No. Hazacord No. 2 BM1 Stranding 19 x 7 Hazacord No. 3 BM2 do. Hazacord No. 4 BM3 do. Super-service No. 3 BM4 7 x 19 Super-service No. 2 Super-service No.. 4 BM5 do. BM6 do. Super-service No. 4 BM7 7x 7 Manufacturer Hazard Insulated Wire Works (division of the Okonite Co.) Do. Do. Rome Wire Company (division of the General Cable Corporation) Do. Do. Do. The cables listed were all twin (parallel duplex) cables having outer belts or cov- erings of approximately -inch high-grade rubber compound, and have the same general appear- ance and relative dimensions as the types of twin cables in general use. The cables were tested under conditions designed to show their approximate perform- ance under mine conditions. Only twin-type cables have met these test conditions. Although the recommended trailing cables are much better and safer for mine use than other cables and withstand being run over by a 7-ton car, they should not be considered as 100 per cent safe. The 7-ton car test represents the minimum limit requirement effective at present under Schedule 2-C, but the test car operates on a straight and level track, and thus does not represent the more severe conditions of mine use such as might result from uneven and curved tracks.

Mar 1, 1931

By Doug Scott

Develop tools that companies can use to comply with 29 CFR 1910.1200.

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

Information is presented on remote sealing of a mine passageway through a borehole by five methods : PPnneeuummaattiicc injection of mineral wool and sand, ureaformaldehyde foam , balloons , urethane foam, and caving by blasting . An adaptation of the method using pneumatically conveyed mineral wool was tried in an operating mine . Further research is needed to simplify and to improve the techniques involved , as well as to explore the possibilities of other methods and combinations .

Jan 1, 1964

By D. J. Bauer

A pure scandium solution was concentrated from 10-4 mole per liter to 0.5 mole per liter by continuous foam fractionation in a spaced, packed column. Recovery in the foam was 77 percent using a spaced, packed draining column with sodium n-methyl-n-"coconut oil acid" taurate as the surfactant. The technique was first studied batchwise in a small unpacked column to determine the more important variables. Optimum surfactant concentration was found to depend on scandium concentration. Extraction and, in general, enrichment ratios were highest in the 2.5 to 3.5 pH range at temperatures ranging from 50° to 70° C. An airflow rate of 136 ml./min. was satisfactory in the equipment used.

Jan 1, 1962

By Edward Thomas

In 1947 the Bureau of Mines, as an accident-prevention measure, decided to advocate the adoption of roof bolting (suspension roof supports) in coal mines where it appeared to be applicable. Subsequent experience has disclosed that the applicability of this support is more general than was first suspected; moreover, comparison of the accident records of mines before and after adoption of the roof-bolting method shows results that more than justify the effort and funds expended. The industry has responded enthusiastically, because roof bolting proved to be not only an accident-prevention measure but also one to increase productive efficiency. In some instances this increase in the productivity of men and machines has been almost incredible and has led many mining men to conclude that through some hocus-pocus they can now cast aside many or all of the time-proven rule of good mining practice. If this tendency is not counteracted, it could easily result in an increase of roof-fall accidents, which may outweigh the benefits of roof bolting and discredit an innovation in roof control that shows great promise of materially reducing our mining accidents. From an economic standpoint it may represent the margin between profit and loss in many mining operations. The purpose of this manuscript is not to propose an inflexible code or set of rules but to summarize the experience to date as a guide for those who have the responsibility for the installation and inspection of roof bolts. This experience consists of approximately 250 investigations of roof failure in which roof bolting was involved either directly or indirectly. It should be pointed out that many of these failures were controlled, occurring during experimental periods, and comparatively few of the accidental failures actually resulted in personal injury, yet a significant number represented potential hazards.

Jan 1, 1951

By N. A. Gokcen

Equilibrium partial pressures of gaseous HCl and H2O over aqueous binary and ternary solutions of HCl and AICls were calculated or estimated in the range of 20° to 110° C, and up to saturation with AlC13?6H2O. The results were extended to solutions containing less than 10 wt-pct FeCl3 by assuming that FeCl3 and AIC13 are equivalent on the molar basis, since both salts have trivalent cations with a cammon anion. The ionic activity coefficient of HCl and the equilibrium constant for dissolution of gaseous HCl were also computed. This research is part of the effort by the Bureau of Mines, U.S. Department of the Interior, to provide thermodynamic data to expand the technology base relevant to the extraction of alumina from nonbauxitic domestic raw materials.

Jan 1, 1980

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By R. V. Ramani, V. T. Burgos, J. A. McClay

General The underground mining environment has traditionally been hostile and as early mines were developed, coal seams with particularly difficult natural conditions were bypassed in favor of those more easily exploited. Barring the discovery of new and novel sources of energy, the depletion of petroleum and natural gas reserves will eventually force the United States back to the use of coal as its primary energy source. Figure 1 illustrates the trend away from coal which has taken place over the past half century. Today, the demand for coal requires a re-evaluation of all coal seams to meet the needs of the energy market. Difficult mining conditions may result in an increase in the consumption of roof control materials, require greater investment in pumping and ventilation systems, and increase the need for in-depth engineering of far greater safety in production plans. They may also cause delays in mine development and curtail production, all of which combine to drive up the unit production cost. It is reasonable to expect that conditions will continue to deteriorate as current reserves are depleted, thus bringing this factor into greater prominence in the future. For several years now, it has become apparent that in addition to economic objectives, coal companies must set and achieve several concomitant objectives to accomodate society&apos;s interest in the conservation of natural resources. Government action to meet this interest has taken the form of two categories of Federal legislation, environmental protection and employee health and safety. The effects of both of these have not been fully evaluated with respect to the total economic picture, although preliminary evidence indicates that an immediate increase in

Jan 1, 1975

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

By Bruce D. Hanson

The Bureau of Mines conducted a series of experiments using four different coal types to determine the effect of attack angle and symmetric bit wear on airborne respirable dust (ARD) generated by point-attack bits and in energy consumption. Neither had a significant effect on ARD at the 95-pct confidence level, but bit wear had a significant effect (95 pct confidence) on specific energy (energy per gram of cut coal) for three coal types, Depth of cut was the most significant factor affecting ARD and specific energy.

Jan 1, 1979