Search Documents

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

By Cecil E. Lester

Since the advent of coal mining, the minimal lighting in the under¬ground working place has been an obstacle to the safe and efficient performance of the miner's many tasks. Compounding this problem is the fact that the machines being operated in the working place are so large that the vertical and horizontal clearances around the machinery are severely limited. Consequently, in these poorly lighted and congested working places, the machine operator is unable to utilize his peripheral vision. He cannot see hazards as they develop and, too often, cannot react in time to avoid serious injury or death to himself or his fellow miners. The greatest hazard to miners inby the last open crosscut is from falls of roof which are often preceded by warning signs such as falling rock fragments, roof supports taking weight, or a sudden reduction in the height of the working place. These warning signs often go undectected because the machine operator's attention is focused on the small circle of light emitted from his cap lamp. Congress recognized the illumination deficiencies, and, in the Federal Coal Mine Health and Safety Act of 1969, charged the Secretary of the Interior with the authority and responsibility for development and promulgation of minimum standards for illuminating working places in coal mines. These standards have been developed and, as stated in the April 1, 1976 Notice, Federal Register, Volume 41, No. 64, will be promulgated on October 1, 1976, as mandatory regulations under Section 75.1719, Title 30, Code of Federal Regulations. The regulations require that the designated surfaces within the miner's normal field of vision be illuminated to 0.06 foot-lamberts while self¬propelled mining equipment is being operated in the working places. The term "working place" is defined in the Act as "the area of a coal mine inby the last open crosscut".

Jan 1, 1976

By J. M. Gomes

The Bureau of Mines has investigated the occurrence and recovery of by-product heavy minerals from sand and gravel operations as a means of assessing the Nation's resources. Sand samples from 63 locations in central and southern California were treated to yield heavy-mineral concentrates. The mineral compositions of the concentrates were characterized by chemical and mineralogical examinations. Additional large quantities of concentrates were prepared from selected deposits that contained significant quantities. Beneficiation studies were performed on these concentrates to recover individual mineral products. Gold was recovered by amalgamation; platinum-group metals and radioactive minerals by flotation; magnetite, ilmenite, and chromite by magnetic and high-tension separation techniques.

Jan 1, 1980

By Michael D. Fenton

The modest mineral industry of Afghanistan continued to suffer adversely from internal disorders that were essentially the result of the continued presence of elements of the armed forces of the U.S.S.R. Despite press reports near yearend intimating that the Soviets might reduce troop strength in Afghanistan, there were no indications of any significant numeric reductions. Indeed, there were clear demonstrations of heightened military actions along the Afghani-Pakistani border, including bombing raids on settlement sites for Afghanis within the territorial limits of Pakistan, actions hardly demonstrative of conditions indicative of Soviet withdrawal.

Jan 1, 1988

By W. W. Odell

"It has long been recognized that coke is a more desirable fuel than bituminous coal in water-gas apparatus of present design, but still considerable headway has been made in the use of the latter fuel as a substiaute for coke. This is particularly true in the Central States where the supply of high-grade coke has been very limited and uncertain during the past few years, and where coking coals of low sulphur content were available in quan¬tities. In fact, with, the present difference in price of coal and coke, it is possible to realize a marked saving when using a coking bituminous coal as generator fuel.Difficulties have been encountered in the use of such fuel, but they have, to a large extent, been overcome. One of the chief obstacles in the use of the more general utilization of bituminous coal for water-gas manufacture, is the fact that, with normal operation, the capacity per unit of time is reduced. This of course is a serious problem for plants operat¬ing at capacity with coke fuel. However, this difficulty can, to a large extent, be remedied by a changed method of operating, and can be entirely remedied by a combination of the latter with a change in the design (or proportions) of a water-gas set. The preceding statement, the reader will understand, refers more particularly to a carburetted water-gas set.In the manufacture of water gas from coke, present practice requires that for continuous 24-hour service the heat of combustion of all the carbon monoxide (CO) generated during the air blow be utilized in addition to the sensible heat of the gas coming from the generator. This is doubly true when making carburetted water gas from bituminous coking coal. The reasons why this is so are apparent when the following factors are considered."

Nov 1, 1920

By J. M. Mutmansky, R. A. Jankowski, M. A. K. Mohamed

"SYNOPSISKnown health hazards associated with the breathing of respirable dusts, particularly silica dust, during mining are becoming a great concern in many parts of the world. The search for effective and low cost dust control methods for underdeveloped countries will help in improving the productivity and keeping the mine environment safe. This article addresses the problem by providing suggestions concerning the easiest and most cost effective methods to control respirable dust in mining and mineral processing operations. INTRODUCTIONMedical BackgroundLung diseases caused by dust in mining operations have been recognized by mankind since the time of the Roman Empire. The writings of Pliny the Younger on natural history reported on maladies associated with dust in mining in the first century AD. However, no significant advances in controlling the lung diseases of miners came about for many centuries. The effects of mineral dusts were further described by Georgius Agricola in his sixteenth century book on mining (Agricola, 1556). After the appearance of Agricola""s book, lung diseases were more readily recognized, but the nature and severity of the ailments associated with mineral dusts could not be readily interpreted.In 1896, the discovery of x-rays by Roentgen advanced the diagnosis of lung diseases and the knowledge of what causes these diseases. In addition, the discovery allowed medical personnel some method of judging the extent and severity of the lung diseases in human beings. During the ensuing years, the term 'pneumoconiosis' became the common term to describe any of the diseases of the lung in which dust particles deposited in the lungs caused fibrous tissue and loss of some of the respiratory function. However, little in the way of social remedies for the diseases resulted until much later. Society was still not ready to act decisively to reduce the causes of lung disease due to the dusty conditions in the work place.Social action against lung diseases did not occur in the United States (US) until the 1930s. At that time, a tunnel driven through a sandstone mountain near Gauley Bridge. West Virginia, caused the death of several hundred workers due to acute silicosis, a severe form of pneumoconiosis caused by silica (Seaton, 1975). Dust conditions in this tunnel were quite bad, causing many of the workers to be subjected to extremely high silica dust concentrations. The severity of the disease in many of the workers became known to the public and prompted the US Congress and many of the states to enact laws to reduce the dust levels."

Jan 1, 1998

By W. W. Odell

"It is common knowledge that extensive lignite deposits occur in the States of Montana, North and South Dakota and Texas. The total area of these deposits and the total amount of lignite in them is so great that the true economic value of lignite is seldom realized. These deposits underlie areas of thousands of square miles. The area of the lignite lands in North Dakota alone is estimated to be approximately 32,000 square miles. Nearly one-third of the total solid-fuel resources of the United States is lignite and approximately 90 per cent of this lies in the Northwest.To the people of the Northwest the more extended utilization of lignite is of fundamental importance, hence any methods for commercially producing salable products from lignite that promise further development of these great fields deserve careful study.The development of our lignite resources has been slow, partly because the districts wherein lignite is found is not thickly settled or highly developed in manufacturing industries, but also because of the physical and chemical characteristics of the lignite. Lignite is classed as a low-grade fuel and may be con¬sidered as imperfectly developed coal -which has a more or less woody structure; it may be of the brown-coal type or darker, denser and more homogeneous, approaching subbituminous coal in character. As mined it contains more than 30 per cent of moisture exclusive of the -rater of decomposition formed .then it is carbonized or burned. The heating value as determined by the calorimeter is approximately half that of good quality bituminous coal. Upon exposure to the air lignite loses part of its moisture, whereupon the lumps chock and split until after considerable exposure, a large percentage of slack is formed. It cannot be stored in large piles so successfully as come other fuels, and it some instances it is more apt to ignite spontaneously in storage or in transit then the higher grade fuels."

Feb 1, 1924

By M. E. Kundick, W. E. Dieter, L. Cohen

The major details of design and maintenance of a seamless stainless steel fume hood system , developed by the Bureau of Mines , are described and illustrated . Operating and housekeeping routines are outlined .

Jan 1, 1964

By L. B. Pankratz

Enthalpies were determined for synthetic chalcopyrite (CuFeS2) between 298° and 1,050° K and for synthetic bornite (Cu5FeS4) between 298° and 1,100° K by copper-block drop calorimetry. Two transitions were found for each compound. The lower transitions were both crystal transformations from tetragonal (low-temperature form) to cubic (high-temperature form). The chalcopyrite transformation occurred at 830' K with a heat of transformation of 2,405 cal/mole; the bornite transformation was at 485° K with a heat of 1,430 cal/mole. The other transitions were of the second order and were presumed to be magnetic in character. The second-order transitions for chalcopyrite occurred at 930° K, and the one for bornite at 540° K. Enthalpy increments, entropy increments, and heat capacities are tabulated at even temperatures above 298.15° K. Equations of enthalpy are also given.

Jan 1, 1970

By Henry Kreisinger, John Blizard

This preliminary statement presents some of the results of tests carried out at the Lakeside Station of the Milwaukee Electric Railway and Light Co. , by the fuel section of the U. S. Bureau of Mines , in cooperation with the research department of the Combustion Engineering Corporation of New York . The object of these tests was to determine the thermal efficiency , ease of operation , and other particulars of a boiler equipped with specially designed furnace and burners for burning powdered coal . The boiler tested haş 13380 square feet of heating surface , and is one of eight boilers equipped with the Lopulco powdered coal system supplying steam to two 20,000 -Kw . steam turbines in the largest power house burning powdered coal . Twenty- six tests were run at rates of heat transference varying from 4000 to 8000 B.t.u. per square foot of boiler heating surface , and the mean thermal efficiency attained was about 84 per cent , based on the gross calorific value of the fuel as fired . The efficiency varied little with the rate of steaming , and its high value is accounted for by the small loss from incomplete combustion and the small amount of excess air which varied from 5 to 36 per cent . The coal burned had a gross calorific value of about 11500 to 12800 B.t.u. per pound , contained 2 to 5 per cent moisture , 33 to 36 per cent volatile matter and 9 to 13 per cent ash, and was so ground thaf 89 to 95 per cent would pass through a 100- mesh sieve . The ash had a softening point of 2150 to 2450 degrees F. , but did not fuse together at the bottom of the furnace because it was partly protected from the flame radiation by means of a series of water tubes connected to the boiler which were placed between the fumace bottom and the flame, ..

Jan 1, 1923

By Richard D. Graves

Pitch from low-temperature carbonization of bituminous coal was hydrogenated at cracking conditions in a continuous bench-scale unit to produce low-molecular-weight oils and tar acids. The pitch contained 15.6 pct benzene-insoluble material, 4.0 pct hexane-soluble oil, and 80.4 pct asphaltene by weight. At 475° C, 7,500 psig, and 1.5 hours residence time, hydrogenation products, based on the weight of pitch, were about 36 pct oil boiling below 325° C, 24 pct hexane-soluble heavy oil, 17 pct asphaltene, 1 pct benzene insolubles, and 12 pct hydrocarbon gases. The yield of tar acids boiling below 250° C was 4.3 pct, and the yields of C6 to C8 paraffins, naphthenes, and aromatics were each less than 1.0 pct. The yield of tar acids was within the range of yields obtained by hydrogenation or high-temperature carbonization of bituminous coal (2 to 5 wt pct). Yields of oil boiling below 325° C increased with increased residence time or temperature. There was little or no effect of residence time on yields of alkali- soluble material which contained tar acids. Yields of hydro-carbon gases increased markedly with an increase in temperature from 475° to 500° C. Lowering the hydrogen pressure to 4,500 psig resulted in yields similar to those obtained at 7,500 psig.

Jan 1, 1962

By George S. Rice, Li C. Ilsley.

A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details: "The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all .appaarances, passed down the shaft causing disruptive disohalges at certain points between the guides and the winding rope, Tending the latter at two places situated respectively 228 feet and 278 feet frem the surface, The distance between the winding rope and the side of the shaft was 6 feet 4 inohes, indicating a spark gap;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft."

Feb 1, 1920

By H. J. Heinen

Malononitrile [CH2(CN)2J, which forms a carbanion in basic solutions, was investigated as a potential leachant for gold and was shown to be an effective extractant in alkaline pulps. Malononitrile was comparable to equal molar quantities of sodium cyanide (NaCN) in leaching gold from an oxide ore and yielded 10 to 20 percent higher recovery in leaching a refractory carbonaceous ore, although dissolution was slower with malononitrile than with cyanide. Complete recovery of the gold from the pregnant solutions was achieved by coprecipitation with a lead salt on zinc dust; the leachant was shown to be capable of regeneration and recycling a limited number of times. Addition of an anion-exchange resin to the carbonaceous pulp containing malononitri1e increased gold recovery from 67 to 95 percent. Some malononitrile derivatives were also shown to be gold solvents.

Jan 1, 1970

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

"The town of Monson in Piscutaquis County, Maine is the, center of an important site industry. Monson slate has a nation-wide reputation, particularly for electrical switch boards, and the deposits have been worked for the manufacture of such products for many years. Open-pit quarrying is the method most commonly employed in obtaining slate. Underground methods have been used in the Peaon Bottom district near Delta, Pennsylvania, but the quarries that were thus operated are now abandoned. Underground methods have been used more extensively in foreign countries, the most famous example being the slate mines at Angers in France, where an over-head stoping method has been employed successfully for many. It is only under special conditions that underground methods can be successfully used. If the deposit is wide and relatively thin, or if the material is too unsound to constitute a safe roof, open-pit methods must be used, for slate is too low-priced a commodity to justify the heavy expense of any timbering methods. It is only where the deposit is relatively narrow, of great depth, and sufficiently sound to afford a strong roof that ordinary mining may be employed.The best slate beds in two of the three quarries operated at Monson are no worked by underground methods. The chief bed worked by the PortlandMonson Slate Co. is 10 feet thick, stands vertical and strikes N. 63º F. The slaty cleavage is vertical and crosses the strike of the beds at an angle of 5 to 10°. The grain or second direction of splitting is vertical and perpendicular to the cleavage. In addition to the 10-foot bed, to 2-foot beds and one 5-foot bed are available but are not now utilized. In theMonson Maine Slate Co. quarry (the old Pond quarry) a greater number of beds available, but at present quarrying is confined to a single bed about 9 feet thick which dips 30º S.E. and strikes N. 47ºF. The slaty cleavage is vertical and strides N. 45º F., while the grain strikes N. 45-50º W. and is also vertical."

Nov 1, 1920

By Kathleen M. PH. D. Kowalski

This paper discusses human judgment and decision-making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision-making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behavior in underground mine fires. The authors assert that stress is one of the factors that decision-makers must contend with in most life-or-death situations. They suggest that a better understanding of individual's judgment and decision-making activities while under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers, and policymakers.

Jan 1, 2008

By J. E. Tiffany, Z. C. Gaugler

An active list of permissible explosives was published in December 1943 as part of the Bureau of Mines Report of Investigations 3736 under the title "Active List of Permissible Explosives and Blasting Devices Approved Previous to June 30, 1943." This list included 180 brand names. Changes in the list that have been authorized to December 31, 1945, placed 10 additional brands of permissible explosives on the active permis- sible list as a result of tests and changes in brand names.. Twelve permis- sible explosives were transferred from the active. to the inactive list. The present list contains 178 brand names. The brand names of the permissible explosives placed on the active list are as follows: American 3-A By test. Apcol No. 1-B Do. Black Diamond No. 11-B DO. Black Diamond No. 55 DO. Coalite G-1 DO. Coelite K-1 Do. Do. Coalite L-1 Coalite IS-1 Columbia B-2 DO. By change in name. By test. Monobel AA The permissible explosives transferred from the active to the inactive list are as follows: Anthracite B, L. F. Big Red No. 8 Independent No. 1, L. F. Independent No. 2, L. F. Independent No. 3, L. F. Independent No. 4, L. F. Independent No. 5, L. F. Independent No. 9, L. F. Independent No. 9-C, L. F. Independent No. 10, L. F. Independent No. 11, L. F. King No. 9

Jul 1, 1946

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington, The investigation consisted of transit and topographic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds Were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and analyzed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing new sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest.

Jan 1, 1948

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 190 psi, and with water-jet-assisted cutting pressures ranging from 1,000 to 6,000 psi. At water pressures of 3,000 psi and higher, dust concentrations were reduced by as much as 85 pct via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1986

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESRJ spectrum of the hydroxyl (· OH) radical spin adduct with .the spin trap 5,5-dimethyl-1-pyrrolintt-N-oxide has been obtained in suspensions of freshly ground quartz particles. The concentration of the spin adduct (and hence of the • OH radicals) increases with the amount of grinding. The dust's potential for the generation of the· OH radicals is maximum when fresh (i.e., immediately after grinding) and decreases to 50% in about a day on storage in air. Studies involving metal chelates .indicate that the • OH radical formation involves mainly the silica surface and H20 rather than the Fenton reaction. The results suggest that hydroxyl radical reaction(s) could be important in the lipid peroxidation and fibrogenicity by quartz dust, particularly .in acute silicosis. INTRODUCTIONIn this paper we report on our electron spin resonance (ESR) detection of the formation of hydroxyl (·OH) radicals in aqueous suspensions of freshly crushed quartz particles. This work was undertaken with a view to find possible clues to the role of free radicals in the pathogenesis of quartz-induced fibrogenicity, commonly known as silicosis. We noted that while silicosis is one of the major health hazards in coal and mineral industries, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still poorly ·understood (Reiser and Last, 1979; Singh and .Rahman, 1987). It is generally thought, nevertheless, that the action of quartz particles on the biological membranes is the starting point of the silicotic process (Parazzi et - al., 1968). A possible clue to the mechanism of the membrane damage by quartz particles, in terms of the role of oxygenated free radicals, is suggested by the following observations. A suspension of quartz particles in contact with alveolar macrophages has been reported (Gabor et al., 1975; Koike et al., 1982) to initiate an enhancement of lipid peroxidation, defined broadly as the oxidative deterioration of polyunsaturated components of lipids. Hydroxyl (· OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (Halliwell and Gutteridge, 1985) and of initiating lipid peroxidation in lysosomal membranes. (Fong et al., 1973). Arong other lines, it is known that exposure of cell membranes, fatty acids, and unsaturated food oils to ionizing radiation, which generates· OH radicals, causes rapid peroxidation (Halliwell and Gutteridge, 1985). Thus • OH radicals (and also other oxygenated species such as Oi, 10 2, and H20 2) might be expected to play a role in the toxicity of quartz. Earlier studies of the aqueous chemistry of quartz suspensions have reported detection of H2O 2 (Kalbanev et al., 1980), implicating the formation of ·OH radicals as transient species. However, we are not aware of any report of the detection of • OH radicals in quartz reactions, and thus the present study was undertaken. Since it-is known that, because of their high reactivity (hence short lifetime) in aqueous media, the • OH radicals cannot be detected via ESR directly (Finkelstein et al., 1980; Buettner, 1982) we have used .ESR combined with the spin-trap methodology (Finkelstein et al., 1980) for studying the· OH formation. The results show that· OH radicals are indeed formed in aqueous suspensions of freshly ground quartz; thus pointing to ·a possible new clue to the cytotoxicity of freshly formed quartz particles and thereby to silica fibrogenicity."

Jan 1, 1988