Search Documents

By S. L. May

Investigations by the Federal Bureau of Mines indicate that hafnium and zirconium compounds of acceptable purity can be extracted from Nigerian zircon concentrates. Chlorination and caustic soda fusion techniques were used to extract 85 to 95 percent of the valuable metals from the concentrate. The extracted hafnium and zirconium compounds were purified by recrystallization of the oxychlorides or by formation of complex salts during chlorination. The zirconium-hafnium product of the recrystallization method contained 15 parts per million of uranium, and the product of the salt-complex method contained less than 10 parts per million of uranium. The hafnium was separated from zirconium by solvent extraction methods. A zirconium product containing 0.3 percent hafnium and a hafnium product containing 4 percent zirconium were obtained. At the request of the Atomic Energy Commission (AEC), work was started to develop techniques for processing Nigerian zircon concentrates in commercial installations presently engaged in producing zirconium and hafnium metals from ores. The Nigerian zircon has a high hafnium content, but the presence of uranium and thorium is a problem not normally encountered in processing zircon concentrates.

Jan 1, 1961

By Jack E. Tress

The Bureau of Mines has been involved for several years in the development of processes for the recycling of solid wastes. As part of this program, a project was initiated to determine the feasibility of producing secondary pig iron from auto scrap. During the test period, 86,000 pounds of shredded auto scrap, along with petroleum coke and fluxing agents, was charged to a submerged-arc furnace of 1-ton nominal capacity. Eighty-eight thousand pounds of pig iron, with an average carbon content of 3.90 percent and an average copper content of 0.2 percent, was produced at an electrical consumption of 512 kW-hr per net ton. A cost estimate of the process showed that the pig, iron might be produced at a cost of $57 per ton.

Jan 1, 1973

By Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out-side headings of a set of five being developed in virgin area, and (2) con-ducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972

By John D. Prater

Thallium is one of the rarer metals that has come into commercial importance in recent years. Although the element was first reported by Crookes in seleniferous deposits in lead chambers of a sulfuric acid plant in the Harz Mountains of Germany, it had no commercial significance until about 190O because of the high cost of extraction. Thallium occurs widely in the earth's crust but is found in such low concentrations that it is recovered only as a byproduct from processing other elements. There are no domestic ores of thallium; the entire output in this country is supplied by the American Smelting & Refining Co. as a byproduct of its cadmium operations at Globe, Colo. Thallium also is recovered from the flue dusts of sulfuric acid works in which thallium-bearing materials are used and as a byproduct of the lithopone industry. This paper describes methods for recovery of thallium from 'white arsenic" and lead Cottrell-precipitator dust of the American Smelting & Refining Co., lead smelter, Murray, Utah. Owing to an enlarged market for thallium because of increased military requirements and expanded peacetime uses, the Salt Lake Station of the Bureau of Mines surveyed the occurrence of thallium in ores, concentrates, and smelter products from all parts of the nation and found the most promising source was certain smelter products of the American Smelting & Refining Co. plant, Murray, Utah. Much of the thallium was being lost in marketed arsenic products; therefore, this investigation was undertaken to develop methods for recovering the thallium.

Jan 1, 1952

By David P. Conover

The U.S. Bureau of Mines (USBM) has developed a computer-assisted Ground Control Management System (GCMS) for near realtime evaluation of underground coal mine ground conditions. The GCMS combines existing mine-monitoring system and sensor technology with automated computer analysis techniques to enhance the acquisition, analysis, and display of geostructural data. The GCMS, which combines mine structure data with other information, such as geologic conditions and mine layout, has provided information on mining-induced stress transfer and pressure buildup associated with several ground control events. The GCMS collects and analyzes shield-leg pressure, ground pressure, and strata movement data to evaluate the structural behavior of an active Western U.S. Iongwall coal mine. Field data are transmitted over a dedicated phone line to the USBM Denver Research Center (DRC) mine monitoring laboratory, 240 km (150 miles) from the mine site. Real-time collection, processing, and analysis of mine structure and shield pressure information has proved to be an effective method for near-face ground conditions while mining progresses. The GCMS provides the mine operator with information to rapidly identify and manage potentially hazardous ground conditions while mining is in progress.

Jan 1, 1994

By Constantine C. Popoff

During 1946 several limestone deposits near Fortson, Snohomish County, Wash., were examined by the Bureau of Mines. These examinations were part of a long-range investigative program of regional mineral supplies required by the anticipated industrial development of the Pacific Northwest. The .study outlined in the following paper was specifically undertaken to disclose new sources of high-purity limestone and to appraise, their economic aspects. The deposits examined -namely the Galbraith, Climax, and Hi, Hi -are somewhat similar in physical features and geologic environment. They are lenticular and belong to the same formation of metamorphosed sediments that underlies the prominent Whitehorse Ridge.

Jan 1, 1949

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

Oil from shales has long been a source of fuel in foreign countries; however, in the fuel economy of the United States this source is classed as a reserve for future needs. In fad, shale oil has never been produced here in quantities necessary to establish oil-shale utilization as a sustained industry. The first known resources of stored energy that man endeavored to utilize were probably wood and water, and from these he directly obtained heat and power, respectively. With the evolution of man came the search for and the development and use of other natural fuel resources, the series progressing through the solid, liquid, and gaseous fuels until today those of one type can be converted into another, depending upon the use for which they are intended. The most important fuels are those that appear naturally in the most concentrated, conveniently obtainable, and usable forms. With the discovery of each new and more concentrated fuel there has been an appreciable increase in the importance of and number of devices for converting these fuels into energy.

Jan 1, 1938

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By Mark S. Sanders

Based on laboratory tests and preliminary field tests of off-the-shelf steel toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners' boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A five month field evaluation compared the prototype boots to the boots the participants usually wear. Although objective slip and fall data showed no significant advantage for the prototype, subjective evaluations made by the participants indicated increased traction for the prototype boots. Approximately 75 percent preferred the prototype to their own boot. Approximately one-third used the lace-up capability. It was concluded that molded soles provide better traction than calendared soles for the underground mining environment.

Jan 1, 1982

By Daryl R. Tweeton

The Bureau of Mines conducted experiments to measure the influence of environment on the friction and wear of a steel-quartz system at several speeds and loads. In each test a quartz block was pressed against a rotating ring of low-carbon steel. Environments used were moist air, dry air, dry nitrogen, water, aqueous oleylarnmonium acetate (ClsH35NH3+-OCOCH3), and aqueous aluminum chloride (A1C13). The sliding speeds were 2.2, 13, and 33, cm/sec, and the loads were 6.8 and 13.6 kg. The coefficient of friction, the wear, and the roughness of the surfaces were measured, and the wear debris was examined. The coefficient of friction was significantly lower in moist air at 2.2 cm/sec than for any other combination of environment and speed employed, and was generally an inverse function of the oxidizing ability of the environment. The coefficient of friction increased somewhat with increasing load. The wear of the steel rings was greatest in dry air at all speeds and loads. The wear of the quartz blocks at 180 rpm was greatest in dry air, but at 12 rpm it was greatest in nitrogen. Friction and wear in aqueous oleylarnmonium acetate and in aqueous aluminum chloride were similar to effect in water alone.

Jan 1, 1976

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965

By Green R. E.

The removal of silica from commercial iron oxide concentrates by dissolution with sodium hydroxide was investigated by the Bureau of Mines as a means for producing supergrade concentrates. The effects of strength of solution, temperature, and digestion time on the extraction of silica were evaluated using eight iron oxide concentrates. Silica extraction from the eight concentrates was enhanced by autoclave leaching in the temperature range of 150° to 250° C and varied from 70 to 95 pct depending on the concentrate used. Superconcentrates containing less than 2 pct Si02 and more than 69 pct Fe were made only when magnetite concentrates were leached in the autoclave. The investigation showed that it is not difficult to obtain a supergrade product if the gangue is mainly quartz.

Jan 1, 1973

By W. E. Miller, John Campbell, W. P. Yant, G. W. Jones

"Because of its interest in accident prevention, the U.S. Bureau of Mines cooperates with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground openings and in developing means for preventing such explosions. For several years this Bureau has been cooperating with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co. in detecting and eliminating combustibles and physiologically harmful gases in manholes in the city of Boston and adjacent territory.These Bureau of Mines investigations° have shown that combustible gases from the usual sources — leakage from gas—distributing systems and from underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas, which are termed here ""soil"" gases, also occur in manholes and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric changes affect their production and passage into the manhole space. These gases appear to be produced by bacterial and fermentation or through reactions of entrapped air in the soil. Soil usually abnormally high in carbon dioxide and low in oxygen, and contain varying amounts of methane. They are especially clangorous to men entering manholes because they lack sufficient oxygen to support life. Owing to the difficulty of constructing gastight manholes the most feasible method for eliminating soil gases from manholes is by ventilation. Consequently the Bureau of Mines initiate 4 study of natural ventilation methods for the removal of these gases from manholes and also for taking care of unforeseen accumulations of combustible gases and vapors.The following factors were considered by the Bureau to be important to the natural ventilation of manholes: (1) Relation of area of ventilation opening* to the capacity of the manholes, (2) size and shape of the manhole, (3) design of the ventilation opening (4) and velocity, and (5) weather conditions."

Jun 1, 1936

By John Paul Gries

During World. War II, when the curtailment of imports led to an unprecedented demand for domestic mica, beryl, spodumene, and other pegmatite minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite mining of these minerals from the Black Hills area of South Dakota. The program involved napping, sampling, and drilling of many pegmatite dikes in the southern portion of the Black Hills and beneficiation conducted in the field and in the Bureau of Mines laboratories at Rapid City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This report describes the occurrence and sampling of the Beecher No. 2 pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Beecher No. 2 pegmatite was started on November 20, 1943, and terminated in the spring of 1944. During this period, the Bureau of Mines took a series of trench samples across the pegmatite at the surface for grain-count studies and chemical analyses. The Geological Survey mapped the geology of the deposit after it was exposed by trenching and stripping.

Jan 1, 1950

By C. Watson Owings

"The mining Industry in the United States is becoming fully cognizant of the hazards of dust in underground mining as well as in surface plants. The dust problem in metal mines has been brought to focus through knowledge of the harmful effects of dust, especially silica, and through adoption of more or less stringent legislation classifying certain types of pneumoconiosis as occupational diseases. The coal-mining industry is aroused principally by the apparently great increase in the dust-explosion hazard resulting from the rapid growth of mechanized mining. The United States Department of the Interior, through the Safety. Division of the Bureau of Mines, has been requested repeatedly to recommend methods of allaying dust in both coal and metal mines. Methods adequate under hand-mining conditions fail to effect satisfactory reduction of dust in more rapid extraction with modern equipment. Studies of methods and equipment for allaying dust are being conducted in both metal and coal mines. Results of these studies are discussed, and indications of possible means of reducing dust concentrations are presented in the hope that the health and 'safety of men employed in the mining industry may be increasingly safeguarded.DUSTThe term ""dust"" is a common one, and yet the meaning is applied to widely different particle sizes. The general term means ""earth or other matter reduced to fine, dry, and powdery particles."" The root from which the word is derived means ""something that can be blown about by the wind."" As a result of tests on the explosibility of coal, the Federal Bureau of Mines has arbitrarily defined dust as being. ""that which will pass through a 20-mesh screen,"" based upon the fact that particles coarser than 20-mesh have little influence on the development of an explosion of Pittsburgh coal-bed dust. The study of dust, from a health standpoint, has given rise to still another definition of dust, namely,- according to Drinker3/, ""solid particles ranging in size from less than 1 micron to about 150 microns."" A micron is 1/25,400 inch, and 150 microns are approximately 1/1,700 inch. Atmospheric dust usually is considered as 10 microns or less, larger particles not being counted under the microscope in determination of dust concentrations."

Apr 1, 1942

By Fred N. Kissell

Air recirculation caused by dust scrubbers at coal mine working faces was examined by the Federal Bureau of Mines with regard to the potential hazards caused by a possible buildup of methane gas. A theoretical analysis indicated that there was no apriori way to predict the effect of scrubber recirculation on methane concentration levels. Experiments conducted in a full-scale model of a working face area indicated that methane levels were dependent to a great extent on the location of the scrubber exhaust, but that the scrubber recirculation did not substantially increase the methane concentration above those levels that would have prevailed were the scrubber not in operation. An analysis of two underground scrubber trials showed that the scrubbers had no significant effect on methane levels, and a review of explosions attributed to recirculation showed that these were characterized by a lack of fresh air as well as recirculation. It was concluded that high methane levels are due more to a lack of fresh air than to recirculation.

Jan 1, 1975

By M. R. Geer

The use of the cyclone as a dense-medium cleaning device was first described by Driessen6/ in 1945, after development of the process in the Netherlands during the German occupation of World War II. A pilot plant was built in the Netherlands soon thereafter, and the first commercial plant was built in 1948. By 1958, 18 plants were operating or under construction.7/ Thus, economic factors in Europe, where the high cost of coal places a premium on efficient cleaning, dictated rapid adoption of the cyclone. American reception of the process differed. The Bureau of Mines presented the results of its own small-scale cyclone experiments in 1946;8/ showing a sharp separation between coal and impurity; adoption by industry now is taking place. There is now much greater emphasis on the efficient cleaning of fine coal, and the first American cyclone plant has begun operating; others are planned or under construction. With the present interest in improved treatment of fine coal, the Bureau of Mines felt that additional performance data on the cyclone would be helpful to industry. Therefore, a complete, open-circuit pilot plant was built to make cleaning trials on American coals covering a wide range of washability characteristics. Five raw coals and one middling product were included in the investigation, and each was cleaned at several densities; 17 cleaning trials are reported.

Jan 1, 1961