Search Documents

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fifth. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in Volume I. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion of that area.

Jan 1, 1948

By G. R. Strimbeck

This is a report on experimental work on development of a gasification process operating at near atmospheric pressures and using finely pulverized coal entrained in oxygen and steam. The gasifier was designed by The Babcock and Wilcox Co. in cooperation with engineers of the Bureau of Mines Morgantown station. The test work discussed in this report covers the first 34 tests made in the pilot plant in which a strongly coking Sewickley-bed coal, ground to either 70 or 90 percent through a 200-mesh screen, was used.

Jan 1, 1954

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the third. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township-map. The description of each half township is followed by a description of each deposit developed in that half township.

Jan 1, 1948

By Carlton E. Brown

This report contains information on the relation between and precision or reproducibility of counts (light-and dark-field) of the dust in liquid from simultaneous impinger, midget-impinger, electric-precipitator, and filter-paper samples. The impinger was the main sampler used from about 1922 to 1939 by industrial hygienists in the United States for collecting samples of unhygienic dust from the atmospheric environment of workers. The midget-impinger, a small modification of the preceding impinger described in 1937, has been the sampler used most since about 1939. Electric precipitators5/6/ have been used to a limited extent, mainly by the Bureau of Mines in the laboratory, for obtaining results comparable to impinger results. A filter-paper sampler for obtaining results comparable to impinger results has been described by Brown. All these samplers have a high collecting efficiency for particles larger than 1 micron in diameter revealed by the usual light-field counting procedure. However, their collecting efficiencies are quite variable for the smaller particles revealed by the dark-field counting procedure used in this study. Published information on the relation between the results of these samplers is limited and scattered. Summaries of some of this information are given in this report along with some previously unpublished information.

Jan 1, 1949

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By Manuel Gomez

Published experimental coke data from a pilot plant slot-type oven were examined by statistical regression analysis. Quantitative relationships were found to exist between the coking rate, bulk density, and fine grinding of the coal, sole-oven expansion, volatile matter, moisture, ash, and carbon con-tent of the coal and coke parameters indicative of size and strength. Regression equations developed from coke data were shown to yield computed values that were in good agreement with experimental results for 11 coke properties. Prediction equations developed were evaluated with an independent set of data. Present results indicate that the variables cited undergo much interaction and the sum of these interactions determines coke size and strength.

Jan 1, 1967

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By P. J. McDonough

The Bureau of Mines designed and tested a hardware-software system for measuring on-line corrosion rates of materials in a rod mill in operation. Currents ranging from 10-6 to 10-3 A and potentials in I-mV increments were converted to a digital signal. The digitized data were frequency-modulated and transmitted from a rotating ball mill to an FM receiver, where they were decoded by computer and then processed in real time using assembly language software. This design approach would allow accurate measurement and control of systems where signals of small amplitude and large ranges are present.

Jan 1, 1988

By James A. Wasson

This Bureau of Mines report summarizes the application of pilot flooding in the evaluation of a potential waterflood project. Aspects of pilot flooding discussed include choice of pilot location, confined and unconfined waterfloods, operational precautions, and comparison of predicted with observed performance. Summaries of published methods of pilot flood data analysis for determination of full-scale waterflood feasibility are presented and their use illustrated for example pilot flood data.

Jan 1, 1974

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CPR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.

Jan 1, 1949

By E. H. Denny

"Reduction of mine accidents appears to depend upon essentially the same fundamentals, whether considered from the viewpoint of the mine operator, miner, State mine inspector, or safety engineer. Conditions of mine operation with respect to safety are governed in most States by a mining law, usually somewhat general in its provisions but more specific than laws dealing with other industries, Methods of mining development and practice evolved through experience have been handed down from generation to generation; many of these are intended to avoid injury to men and also loss of property. To carry out the intent of these bases of law and experience relating to safety supplemental measures and conditions are necessary. Among these may be: (1) Planned safety rules adapted to the mine and compliance by both officials and Miners with such of these rules as pertain to their work; (2) a supervisory force adequate and competent to ¬administer the mining laws and safety rules; (3) discipline adequate to secure compliance with safety measures; (4) safeguards against mechanical, electrical, falling, and other hazards; (5) mining operations planned with respect to safety of workers; (6) an active safety organization of officials and employees; (7) education of officials and employees in safety practices; and (8) an active sustained interest in safety by management and employees.This paper presents the viewpoint of the safety engineer, though a safety engineer connected with a specific mine or group of mines would be in a better position than the writer to present the industrial engineer's thought. The application of the mine safety fundamentals just outlined will be given consideration from observations of methods used by safety engineers and supervisors.The term ""safety engineer"" includes men of various duties, various degrees of experience, and various authority. Depending upon the size of the operation or the interest of the management in safety, the safety engineer may have accident prevention as his sole duty; he may be the head of a sizable safety organization; or he may be in part a claim agent; a statistician compiling figures for the enlightenment of the company, the public, or a mining institute meeting; a surveyor who must convince the miner that his scale of 10/10 equals 1 foot does not defraud the miner of 6 inches to every yard measured; or he may be by heaven¬ly gift an orator capable of assuring the employees that ""all's right with the world""; he may be a young engineer gaining, experience while checking the observance of company rules and investigating accidents; or he may have the physical ills frequently resulting from several decades of mining experience and instead of a pension, the position of safety engineer has fallen to his lot. He may have mine-operating authority to correct immediately a dangerous condition or practice or he may have his recommendations officially disregarded at the monthly meeting or when the bottom of the desk basket is reached. He is likely to find that his viewpoint on accident reduction is considered unsound today because of youth and inexperience and unsound later because of old age and senility. He is likely to find the easiest course to be that of attributing to Providence and the carelessness of the worker the mishaps that result in the removal of a man to the hospital or the morgue."

Dec 1, 1936

By Donald W. Scott

Chemical thermodynamic properties for the ideal gas state from 0 to 1500 K are tabulated for all of the alkane hydrocarbons through C10. These properties are based on correlations of the extant data for the entropy, vapor heat capacity, and enthalpy of formation of individual alkanes and the equilibrium constants of alkane isomerization reactions.

Jan 1, 1974

By M. H. Kersten, G. A. Brady, Jerry W. Ramsey

Anthracite samples were oxidized with nitric acid to prepare products representing intermediate stages of oxidation . Similar oxidizing conditions affected different anthracites to varying degrees as characterized by peptization behavior with 0.1 N NaOH . Techniques used in attempts to separate and characterize the products included esterification , absorption spectrophotometry , sublimation , chromatography , electrophoresis , metal salt formation , and solvent extraction . Mellitic acid , either free or in the form of metallic salts , was identified in the acid- soluble products from 10 tests in which the anthracite was treated with nitric acid for periods varying from 24 to 1,000 hours . pentacarboxylic acid was also found in some products . Other benzene carboxylic acids were not present in amounts detectable by the methods used in this study . The acid- insoluble residue from nitric acid treatment varied significantly in solubility behavior toward different classes of solvents . The most effective ones tried included polar oxygenated solvents and pyridine . Infrared spectra of the extracted material indicated that similar compounds were extracted by the different solvents . Aliphatic amines and aniline peptized the residue and o- toluidine reacted with it . Organic material separated from the residue by peptization with dimethylformamide contained 1 percent ash , consisting of more than 50 percent zirconium .

Jan 1, 1964

By R. R. Wells

This report summarizes the results of laboratory investigations by the Alaska Mining Experiment Station, Juneau, to determine the practicability of treating cinnabar-stibnite ore by bulk flotation and controlled-atmosphere roasting of the concentrate. Ore from the Red Devil mine near Sleetmute, Alaska, was selected for testing; it is typical of ores widely distributed throughout the Kuskokwim River Basin. The material, consisting of stibnite and cinnabar in ankerite, dolomite, and quartz, assayed 1.55 percent Hg and 2.87 percent Sb. Continuous treatment of the ore in a laboratory flotation circuit recovered 95.7 percent of the mercury and 82.6 percent of the antimony in a concentrate that assayed 20.4 percent Hg and 34.6 percent Sb.

Jan 1, 1958

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By R. L. Crosby, L. W. Higley

Magnesium- rich magnesium- aluminum- zirconium alloys in the cast and in the extruded and heat- treated condition were studied to identify the phases present and to determine phase distribution . In cast alloys , two intermetallic compounds were identified : ZrAla by X- ray diffraction ; and Mg₁ Al₁₂ by microscopical observation . Based on microscopical comparisons between the known phases in the cast structures and the phases in the structures of extruded and heat - treated rods , ZrAl₂ and Mg1 , Al12 were identified in the structure of the latter . The presence of these intermetallic compounds in rod specimens could not be confirmed by X- ray diffraction . ZrAl₂ was observed in the structure of extruded and heat - treated rod specimens containing as little as 0.01 weight - percent zirconium . The presence of aluminum restricts the solubility of zirconium in magnesium because of the strong tendency to form ZrAla . This intermetallic compound segregated in clusters of small particles in the matrix of cast alloys , and only slight improvement in distribution was noted when the alloying techniques were varied .

Jan 1, 1964

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,421 samples, representing the products of 131 companies. The samples were collected during June, July, and August, 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1954

By O. C. Blade

A summary of the characteristics of motor gasoline for the winter 1951-52 is presented in table I, and for comparison, a similar summary for the winter 1950-51 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. The results of this survey show that octane numbers have risen slightly since the summer of 1951 but are below the record levels of the winter of 1950-51. The fractions of a unit change since the summer preceding have resulted in the research and motor-method octane values being virtually the same as the figures for the survey of summer 1950. In volatility characteristics the winter gasolines have changed very little. Average Reid vapor pressures are 10.5 pounds for both grades of fuel compared to 10.4 and 10.5 pounds for premium and regular-price gasolines, respectively, of the winter of 1950-51.

Jan 1, 1952