Search Documents

By Henry M. Harris

A study was made by the Bureau of Mines to determine if shapes of oxide-glass compositions could be roll-formed at high temperatures, and to find the conditions required for adequate formability. A unit with directly connect' furnaces and heated rolls that allowed forming of most of the compositions developed. Glasses of the feldspar type were chemically unreactive with the alumina grains, and allowed the best roll forming. Optimum forming was attained at temperatures of 1,400° to 1,530° C, with compositions containing 30 or 40 percent feldspar and 60 or 70 percent alumina. Formability was better when compositions contained minus 325-mesh materials, rather than coarser or finer powders. In many cases, roll-formed shapes had physical properties equal to or better than the normally sintered shapes of the same composition.

Jan 1, 1967

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959

By P. M. Brown

The Bureau of Mines is investigating a dewatering technique for coal-clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong stable flocs that can be dewatered on a static screen. A field test unit (FTU) using this technique was operated at approximately 400 gal/min, using a waste stream from the flotation circuit of a coal preparation plant. Consolidated coal-clay material con-taining 55 to 60 pct solids was produced when the flotation circuit slurries of 2.7 to 8 pct solids were treated with 0.1 to 0.3 Ib PEO per ton of solids. The FTU was also operated at 64.5 and 87.5 gal/min using a portion of the underflow slurry from the preparation plant's thickener. Consolidated coal-clay material containing 55 to 60 pct solids was produced when the thickener underflow slurries of 19 to 24 pct solids were treated with 0.08 to 0.2 Ib PEO per ton of solids. PED-treated materials continued to dewater when placed in a pit.

Jan 1, 1983

By R. E. Brewer

A critical review of the numerous test methods that have been devised for measuring the "plastic" and "swelling" properties of bituminous coking coals and the practical evaluation of the data obtained has long been needed. The author appreciates fully, first, the arduous problem of doing justice to the merits and limitations of the many original test methods and their manifold modifications and, second, the more difficult task of interpreting the test data obtained in their practical applications to the important problems involved in the coking process. It has been the constant aim of the author to point out the broader significance of the test principles employed in the different classes of test methods and the usefulness of the test data obtained in relation to the problem of coking bituminous coals, rather than to stimulate unduly a controversial criticism of the merits and limitations of any particular class of test methods or of individual test methods devised by different workers. The task has been quite difficult because of the almost total lack of accepted test standards and specifications.

Jan 1, 1942

By E. R. Palowitch

This report is the result of a series of coal-cleaning tests using a dense-medium cone-type washer. Detailed results are given for 2 tests using a magnetite medium and 4 tests using a pulverized-refuse medium. Approximately 120 float-and-sink tests and over 500 separate chemical analyses were made in conjunction with these tests. In these tests higher recovery efficiencies and sharper separations were obtained when using a magnetite medium, especially on coal sizes below one-half inch. When sizes above 1 inch at low specific gravities of separation are cleaned, the pulverized refuse medium compared favorably with the magnetite medium.

Jan 1, 1956

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By A. J. Kraemer

This paper is the second and concluding report of the results of the Bureau of Mines' twenty-second semiannual survey of motor fuel marketed in the United States. The first paper Was published as Report of Investigations 3063 and reported data relating to gravity, vapor pressure and distillation range of the samples. The present paper deals particularly with results of the determination of copper strip corrosion (method 530.22), color (method 10.11), sulphur content by the lamp method, copper dish evaporation residue (method 530.1), and "gum" content as given by the steam-oven method as developed by the Bureau of Mines. The price at the time the sample was taken and the tax are also stated for each sample. The sample numbers used throughout this report are identical with those used in Report of Investigations 3063; for example, No. 225 of this report is the same sample as No. 225 of Report of Investigations 3063. This is the first semiannual motor gasoline survey of the Bureau 6f Mines in which some data were obtained on antiknock values for samples collected in the survey. The Bureau of Mines is not provided with equipment for making these tests in its own laboratories, but composite samples were tested in the laboratories of the Bureau of Standards and the report on these samples is given as a supplement to this paper (pp. 11 to 14).

Jan 1, 1931

By d&apos, D. V. Andrea

Nine rock properties were determined for rocks coming from 49 locations and having a wide range of compressive strengths. Plots of the nine rock properties versus each other were prepared. A stepwise multiple linear regression analysis was performed to obtain several equations for predicting compressive strength. Both linear and curvilinear relationships were assumed between compressive strength and the other rock properties. The prediction equations had multiple correlation coefficients ranging from 0.947 for an equation with 1 variable (point load tensile strength) to 0.986 for an equation with 25 variables. Of the properties tested only point load tensile strength could be used alone to estimate compressive strength with fair accuracy.

Jan 1, 1965

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953

By E. H. Illsley

This bibliography is the first report of a Bureau of Mines research project on thermoelectric materials. Interest in such research has increased because of recent success in the design of commercial products, including generators and refrigerators, using the principles of thermoelectricity. This success made possible by the discovery of semiconductors that have much higher [effincies] than the metals and alloys formerly studied. Thermoelectricity is a term that includes a large number of phenomena relating heat to electrical energy. However, the moat important applications arise from two effects discovered by Seebeck in 1822 and by Peltier in 1834. When pieces of two unlike materials are joined at their two ends to form a continuous circuit, both of these effects may be observed. If the two junctions are maintained at different temperatures, an electromotive force known as the Seebeck voltage is generated. If, on the other hand, a current is made to flow through the circuit, the junctions of the materials will be found to differ in temperature. This phenomenon is called the Peltier effect.

Jan 1, 1959

By J. J. Hoeppner

Lignite samples were collected so as to be widely representative of the extensive deposits in the western north-central area. These were carbonized at temperatures ranging from 450° to 550° C., according, to a standardized procedure. In general, product yields varied; extremes obtained on selected samples show char recoveries on the moisture- and ash-free basis as 56.7 percent for slack lignite or "leonardite" to 80.8 percent for a concentrate of the fusain component from a typical face sample; normal lignite samples averaged approximately 70 percent. Tar-plus-light-oil yields ranged from 3.3 percent for the fusain concentrate to 11.0 percent for a normal sample, averaging approximately 8 percent; gas recoveries varied more widely both in yield and in composition, ranging, from 10.0 percent to 27.7 percent, the latter being from leonardite and quite high in carbon dioxide. Sampling was conducted with the view of representing, as nearly as possible, all beds delineated by Brant (2);4/ many are necessarily missing since collection was confined largely to worked deposits. Data presented in this report indicate a general uniformity of North-Central lignite in respect to low-temperature carbonization, with a few possible exceptions of a local nature. When processed according to the indicated conditions, maximum tar yield may be realized with minimum loss of recoverable heating value of the original coal. Natural weathering of lignite, however, does affect tar yield adversely and should be held to a practical minimum in any commercial operation.

Jan 1, 1956

By Henry H. Ginsberg

The effectiveness of 0.01 pct. molybdenum, as ammonium molybdate impregnated on coal, on the hydrogenation of a high-volatile bituminous C coal at 8,000 p.s.i.g. and 460° to 480° C. has been studied in a pilot plant by the Federal Bureau of Mines. Under these conditions, the Bureau obtained 98 to 99 pct. conversion5/ of coal to liquids and gases at throughputs of 29 to 101 lb. of m.a.f. coal per cubic foot of reaction space per hour. At 460° C. the indicated yield of oil ranged from 63 pct. (based on m.a.f. coal) at a throughput of 35 lb./c.f.h. (pounds per cubic foot per hour) to 68.5 pct. at a throughput of 58 lb./c.f.h., and the yield of gaseous hydro-carbons ranged from 25.5 to 19 pct. at the same throughputs. The maximum measured yield of oil boiling under 325° C. was 47 pct.

Jan 1, 1960

By A. E. Nagel, J. E. Carpetta, M. G. Zabetakis, T. D. Moore

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

By Chas. F. Jackson

During the past 5 years the Bureau of Mines has published information circulars dealing with mining methods and costs at 78 ore mines; 7 circulars, each of which is devoted to a discussion of one of the principal mining, methods; and 23 circulars dealing with special phases of mining, such as ventilation, shaft sinking, tunnel driving, the cost of equipping and developing prospects and small mines, underground transportation, diamond drilling, and ground support. These circulars were written by many different authors, and in order that the method of presentation and the basis for compilation of data might be the same in all the papers the Bureau drafted an outline to be followed in their preparation. To clarify the data in these circulars, which are in the libraries of many engineers and mining companies, and the summarized data presented in this paper, that portion of the outline dealing with cost and labor-performance data is reproduced below.

Jan 1, 1934

By R. V. Ramani, R. Bhaskar

"The National Academy of Sciences (1) recognized the importance of studying the spatial and temporal characteristics of respirable coal mine dust atmospheres. In this paper, the progress to date of a research project on dust transportation and deposition in mine airways is presented. A mathematical model is proposed for studying the transport of dust. A source representative of dust generation in underground coal mining is defined. The influence and applicability of surface roughness, dispersivities, coagulation and reentrainment to vine dust flow arc examined. A convective-diffusion model is proposed for the transport and deposition of dust in mine airways. Using the model, the spatial and temporal characteristics can be evaluated in terms of dust concentrations in the mine atmospheres.INTRODUCTIONThe prediction of the behavior of fine particles Is Important in many fields of science and engi¬neering including physics, chemistry, mining, mineral processing, and atmospheric science. In mining from the health point of view, fine coal dust is associated with the appearance of pneumoconiosis in miners exposed to the dust. Also, in addition to being a nuisance factor obscuring visibility and general mobility of miners, it can lead to sudden catastrophic incidences of explosions. This paper outlines the progress to date of a research project on dust transportation and deposition in mine airways. A mathematical model is proposed for studying the transport of dust for the various mechanisms. The dust dispersion is defined in terms of a dispersion term determined from experimental data by Skubunov (23). Coagulation is considered as one of the mechanisms that can lead to changes in the particle size distribution. Reentrainment as a possible secondary source of dust was examined during model development but was not included in the final model."

Jan 1, 1988

By R. H. Nafziger

The Bureau of Mines evaluated 18 domestic titaniferous materials with widely varying compositions, mineralogy, and physical properties in electric-arc furnaces, Techniques were devised to recover both the titanium and iron values contained in these materials so that the reliance of the United States on foreign sources of higher grade ilmenites and rutile might be decreased. Most of the tested titaniferous materials responded well to lower grade or byproduct reductants, such as bituminous coals, charcoal, and coke breeze. Sufficient slag fluidity was realized by maintaining from 8 to 12 wt-pct iron in the slags; no contaminating fluidizers were required. Fluid slags containing up to 79, 70, and 54 wt-pct Ti02 were realized from east coast ilmenites, a rock ilmenite, and a titaniferous magnetite ore, respectively. A carbon-lined furnace shell is recommended for minimum slag contamination. Good results also were obtained during extended submerged-arc furnace tests.

Jan 1, 1980

By N. E. Hanna

Originally developed for use in coal mines where on-shift blasting with explosives was prohibited, compressed-air blasting has been used for the past 15 years as a substitute for fixed explosives. With the current commercially available compressed-air systems -Airdox and Armstrong -coal is dislodged by a high-pressure discharge of air from a pressurized shell placed in the coal borehole. In the original systems stationary compressors were mounted on the surface or in the underground ventilated areas. These proved so successful that a mobile compressor unit was developed for use at the working face. Because of the possibility that such a unit might operate in a gassy atmosphere, the Bureau of Mines has investigated the hazards associated with operation under conditions where firedamp could accumulate in explosive concentrations. ACKNOWLEDGMENTS Grateful acknowledgment is made of cooperation of C. E. Carter, H. R. Hiller, R. E. Kennedy, H. Kohn, H. D. Metzinger, J. Mahoney, J. Nickovich, G. So Scott and I. Spolan in the experimental work.

Jan 1, 1956

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By S. J. Schatzel, P. W. Jeran, W. P. Diamond, F. E. McCall, F. Garcia, J. C. LaScola, T. P. Mucho

The National Institute for Occupational Safety and Health, Office for Mine Safety and Health Research, is investigating the geologic and mining factors influencing the migration of longwall gob gas. One goal of these studies is to optimize methane drainage strategies to reduce the volume of gob gas that reaches the underground workplace. As part of this research effort, longwall gob gas flow paths in a mine operating in the Pittsburgh Coalbed, PA, were investigated using SF6 tracer gas. Tracer gas released into the ventilation airflow underground generally stayed in the bleeder system and was vented at the associated bleeder fan shafts. Tracer gas injected into an inactive (intaking) gob gas venthole migrated to the two inby producing ventholes on the study panel, indicating that all three ventholes were in communication. The tracer gas that was injected into the gob generally stayed in the gob and only migrated to the ventilation system in response to the venthole on the study panel closest to the injection hole going off production. Tracer gas flow velocities in the longwall gob reservoir and factors influencing the production performance of gob gas ventholes in the study area are also discussed.