Search Documents

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July l, 1936.

Jan 1, 1940

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

By Galen G. Waddell

The Deep Creek zinc and lead mine afforded an excellent example of a relatively small underground mine operation that approached the low mining costs of large, highly mechanized mines, An open stope mining method incorporating sublevel benches and vertical long holes was used (fig. 1). Detailed descriptions are given on the exploration program, stope development, stoping procedures, and pillar removal. Pressure grouting was used to check the inflow of water and thus prolong the life of the mine. Statistics on mining costs and on electric power consumption, haulage from mine to mill, and milling costs are included.

Jan 1, 1963

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors' experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982

By Gordon R. Sima, John L. Bennett, Roger L. King

Electric shocks are a serious problem in the mining environment. Because of extremely wide ranging use of electrically powered equipment in the mining industry, the hazard to personnel due to electrical shock and related injuries are not restricted to any single area but cover the entire spectrum of mining activity. Electrical accidents, resulting in personal injury, due to im- proper or complete lack of grounding of electrically operated mining machines, form a significant percentage of the overall electrical accident picture. The object of this paper is to describe methods of detection of unsafe electrical conditions with respect to the grounding of electrically operated mining equipment. It also includes a discussion of prototype instruments which effectively monitor the condition of the grounding safety devices currently in use on mining equipment and warn of dangerous conditions as soon as they appear. The paper is based on work accomplished under USBM Contract Number 50357115. The contract was initiated under the Pittsburgh Mining and Safety Research Center Program. It was administered under the technical direction of PM and SRC with Mr. Roger L. King as the Technical Project Officer. Mr. Daniel B. Dawkins was the Contract Administrator for the Bureau of Mines.

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By A. C. Munro

This paper, which describes the milling practice at the Britannia concentrator, Britannia Beach, B. C., is one of a series being prepared by the Bureau of Mines. The concentrator treats copper ore at the present rate of 6,000 to 7,000 tons of dry ore daily and produces copper concentrate and pyrite concentrate by selective flotation methods. The copper concentrate is smelted and the pyrite product is utilized for acid manufacture.

Jan 1, 1932

By John J. Sammarco

The U.S. Bureau of Mines seeks to increase safety and efficiency in U.S. coal mines. One approach is to develop technology for automation of a continuous mining machine. Realization of an autonomous mining machine requires development of subsystems for machine intelligence, navigation-positioning, and computer control. This report focuses on investigation of one subsystem, an onboard heading system, which would be responsible for determining and controlling machine heading. The onboard heading system investigated is a multisensor system to determine machine heading, pitch, and roll. A directional gyroscope provides heading (yaw), fluxgate sensors provide a compass heading, and gravity-referenced clinometers give machine pitch and roll. The system utilizes a dedicated microcontroller networked to an external system of computers. Tram commands, supplied to the network from external computers, are executed by the onboard system. Sensor feedback is employed for closed-loop control of machine heading by controlling pivots and turns. The report discusses operating limitations and error sources of system sensors and presents test results of closed-loop control of machine heading. Results of tests with a mining machine are used to exhibit various sensor shortcomings and to evaluate control of pivots and turns.

Jan 1, 1990

By J. F. Barkley

[There 1 s [\ general conce:!?t in the coal trade tha t the ;noi sture-and ash-free B. t.'I. of coal from t.he oome seam, and surely from the same mine, is substantially a cor.stant: that calculatio!: of the ::1oisture-and ash-free B. t. u. value f~~oJl t he proxima te ru:al~rsi sand. 3. t. u. determined in tl19 laboratory 111ill reveal v:?letller a coal came f~'om a. given : area or seam; and that, having this constant, the 3.t.u. value of a coal sample can be c lculatcd fairl...' closely 11:0on a? dry or as~received basis from the r.lois]

Jan 1, 1941

By H. R. Shell

Fluorphlogopite mica was synthesized from inexpensive and abundant olivine, clay, feldspar, and sand (plus K2SiF6). The raw materials were melted in crucibles and in an internal resistance electric furnace. The melts yielded >95 percent mica. The major difficulty encountered was incomplete settling of the highly dispersed ferroalloy. This problem was not completely solved. Reducing agents tried in melts of 300 to 400 pounds were carbon, silicon, and silicon carbide. Carbon slowly reduced the iron of the raw materials, with much fuming. Silicon apparently was oxidized ahead of the melting and was ineffective under the conditions obtained. By far the best reducing agent was silicon carbide. With silicon carbide, fuming did not occur and ionic iron content of the mica flake approached 0 percent. However, even with SiC, the highly dispersed globular iron did not completely separate from the mica portion. The fluorphlogopite made during this investigation should be suitable for metallurgical use. A byproduct ferroalloy containing about 5 percent nickel, 3 to 5 percent chromium, and some cobalt was obtained. Because of the highly dispersed metallic ferroalloy, the mica was not deemed suitable for electrical or electronic uses.

Jan 1, 1962

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By Andrew Allan

During recent years underground production for the Pennsylvania anthracite region has reached the lowest output per man per day figure of the last decade and a half. This fact, combined with increased unit costs for labor and material, has forced the market price of anthracite ever higher. Over the years the mines have become deeper, and haulage distances have increased, thus adding to the mining costs. The industry now recognizes the need for new mining techniques to offset increasing costs. The Federal Bureau of Mines, through its Anthracite Research Laboratory, is engaged in a program of underground-mining research in cooperation with anthracite-producing companies to aid in reestablishing the economy of the region by introducing methods and/ or machines that will reduce underground-mining costs and, at the same time, enhance the safety of the workmen.

Jan 1, 1953

By Charles L. Kimbell

For the world mineral industry as a whole, the year 1981 was a period of continuation and, in some instances, an acceleration of negative trends extending back into 1980. Most available statistical data reflected stagnation or downturns in activity. Levels of production, trade, and consumption declined for a substantial number of leading mineral commodities, including, most notably, steel and petroleum. Investment, if not lower than in 1980, was evidently increasing at a more modest rate. Prices for major mineral commodities were generally lower, at least in terms of constant dollars, and in some cases even in terms of current dollars. Prospects of a major reversal of these patterns seemed dim. The mineral industry, however, was far from alone in this general downturn; most other elements of the national economies of the world's nations fared little better. General conditions of inflation, recession, and reduced industrial product consumption were reflected in most other sectors of the total economy. International political events continued to influence mineral output and flow but had less influence on overall levels of activities than on the geographic distribution of these activities. The Iran-Iraq war certainly played a role in reducing mineral industry activities in those nations, but the commodity most affected, petroleum, was available from other sources in sufficient quantity that, in the face of reduced demand, a substantial surplus developed.

Jan 1, 1983

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By Ivette E. Torres

The final 26 tables of this chapter, tables 24-49, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Mainly because of the separation of the countries that formed the U.S.S.R., the column that provided a 5-year average, was deleted. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1992. This group of tables now includes each of the top 19 crude minerals in 1983 in terms of value of their output plus 3 others of lesser rank. These 22 crude mineral commodities accounted for more than 98 % of the estimated value of world crude mineral production in 1983. Coal production, included in the 1983 value of production table as two separated entries, is combined in one table in this chapter. World output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1994

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.