Search Documents

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By Mark Sanders

This report compares a proposed 10/60 "piggyback" 02 generating self-rescue unit to the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and subjects performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 or self-rescuer attached to their belts. Task completion time was longer on all tasks when wearing the 10/60 unit, although only locomotion was statistically significant. The 10/60 unit was bumped over 100% more often than the standard self-rescuer. Implications for design of the proposed 10/60 container are: 1) unit?s container must be extra durable to withstand the added abuse it is likely to receive by low coal miners; and 2) extra consideration must be given to preventing the device from slipping on the belt while working, especially in low coal.

Jan 1, 1980

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By Earl R. Maize

Epoxy and polyester-type resins were injected into coal-mine roof strata of the thick Freeport coal seam in Allegheny County, Pa., at test sites in roof that had been exposed several weeks, in newly exposed roof, and in strata over solid coal. Test results indicate that the method of strengthening bituminous-coal-mine roof by injecting a bonding material into the roof strata can be developed into a safe, efficient support system. If roof bonding will become a standardized method of roof support and reinforcement or if it can be effective when used with other types of roof support can be determined only by extensive experimentation in various coal beds. Observations and conclusions are shown at the end of this report.

Jan 1, 1959

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

By Henry P. Chandler

THE year 1950 was one of increased activity in almost all branches of the abrasives industry, with nearly all abrasive materials showing a marked increase in tonnage and value. New records were made In the production of tripoli, ground sand and sandstone, pumice and pumicite, and garnet. Total production of crude artificial abrasives in the United States and Canada increased 17 percent in tonnage and 30 percent in value. Imports of industrial diamonds increased 100 percent in total value and 72 percent by weight, the 1950 importation being the largest since 1944. Imports of corundum increased 76 percent in tonnage and 4 percent in value.

Jan 1, 1953

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

By R. Michael Digman

Few efforts have been undertaken to date to assess the quality of mandated coal mine health and safety training for new miners and for experienced miners. This study was concerned with the quality and effectiveness of existing classroom health and safety training programs. The study involved field data collection through pre- and posttesting of trainees, audio-taping class sessions, and administering short feedback forms with trainers and trainees at 14 sites in West Virginia, Maryland, Kentucky, and Pennsylvania. Results indicate that goals, methods, materials, and outcomes of existing training programs vary widely among trainers and sites. The report provides less by way of solution to problems, than it highlights the breadth of issues that relate to the question of training effectiveness and quality. The report concludes that additional work by industry, labor, government, and academia is necessary in order to improve health and safety training programs. Recommended steps are: (a) to develop performance standards and measurable criteria in each of the types of mandated training, (b) to develop better training of trainers, (c) to develop expanded training support services. and (d) to undertake further research and development in health and safety training in the mining industry

Jan 1, 1982

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By T. M. Romslo

"The Keystone and St. George properties are in the so-called Johnson Camp area and adjoin a property that in recent years has become a steady producer of low-to medium-grade copper-zinc ores. The Keystone Copper Co. was active intermittently from 1908 to 1938 and during 1926 to 1937 produced a recorded 1,100 tons of 5 percent copper ore. There is no evidence that ore has been produced from the St. George property.In the Johnson Camp area both igneous and sedimentary rocks ranging in age from pre-Cambrian to Quaternary are exposed. The ore bodies are in the Paleozoic rocks and occur principally in the Abrigo formation, which is composed mainly of limestones and shales. The rocks of the productive zones are metamorphosed and are cut by systems of fractures and faults. Chalcopyrite and sphalerite, the principal ore minerals, replace altered limestones to form deposits locally called mantos and chimneys.Investigation of the Keystone and St. George deposits by the Bureau of Mines included topographical and geological mapping of the surface and the underground workings and diamond drilling from the surface. A total of 10,067.8 feet was drilled in 22 holes. The drilling started November 13, 1947, and was completed August 19, 1948.This report records factual information obtained during the course of the investigation."

Jul 1, 1949

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By G. E. McElroy

[The ventilation of development faces in mines for diluting gas or dust concentrations aid in hot mines for providing air-motion cooling affect, by fan-pipe units discharging high-velocity streams of air close to the face, is an important phase of mitre ventilation. The effectiveness of such units depends largely on the air-flow distribution between-the pipe discharge said the face, a subject on which little definite information is available. A study of the air, flow from grills into rooms3/ has provided sore basic data, but under conditions so different from mine fan-pipe installations in development ends that tae data to are of doubtful application to mine installa¬tions, owing to differences in air-flow conditions. The purposes of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pine lines in nines. The s series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of tripe, and adjacent calls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made b y short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects cue to size anti shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs is and ago se reported.]

Jan 1, 1940

By I. L. Nichols

The inplace cyanidation leaching of gold from placer deposits is a potential method for treating gravels too deeply buried and too low in gold content to be processed economically by conventional dredging methods. Laboratory experiments were made to evaluate those placer cyanidation factors adaptable to small-scale studies. The variables investigated included gold particle size and location in sand beds, cyanide solution flow rate, and cyanide solution strength as factors affecting gold solubility rates. The solution flow rate, in turn, was influenced by variables such as bed slope, solution head pressure, and sand size, and the effects of these factors were studied. Free gold, minus 150-mesh and finer in size, is rapidly dissolved by dilute cyanide solutions from mixtures of gold and silica sand prepared to simulate placer deposits. About 94 percent of minus 325-mesh free gold was extracted in 5 hours from silica sand mixtures, and 94 percent extraction of minus 150-mesh gold was obtained in 21 hours with 0.1 percent NaCN solutions. Moving solutions were almost twice as effective in leaching free gold from silica sand mixtures than stagnant solutions.

Jan 1, 1971

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962