Search Documents

By R R. Singh, U K. Dey, S K. Roy

"Commercial explosives being a heterogeneous mixture of many chemical compounds in prefixed proportion, their velocity of detonation (VOD) may vary from batch to batch, due to variations in the proportion of the chemical composition and process parameters even within their tolerance limits. Inherent limitations of measuring methods and human variations during measurement also add to the variation in VOD values determined practically. Therefore, it is customary to define a range of VOD values rather than a fixed value of VOD for a particular explosive.Variations in VOD values of four commercial permitted explosives in India were evaluated under open unconfined condition using Dautriche method and a resistance wire method based continuous VOD meter. Comparative evaluation of VOD values of selected explosives were aimed to check the relative effectiveness of continuous VOD measurement of small diameter cartridged permitted explosives using cheaper co-axial wire instead of recommended costly VOD rods along with the continuous VOD meter. Results of evaluation revealed that continuous VOD of commercial small diameter cartridged explosives could be determined using cheaper co-axial resistance cable with comparatively better accuracy than the most commonly used Dautriche method."

Jan 1, 2007

By Albert G. Funk, Gary M. Thornley

The available energy of aluminized ANFO and aluminized slurry blasting agents has been measured by seismic methods, calculated theoretically, and compared. With aluminized ANFO it is concluded that aluminum concentrations should be restricted to less than 10 percent because of diminished energy yields at high aluminum concentrations. However, with aluminized slurry it is concluded that efficient use of aluminum can be made at aluminum concert"rations up to 18 percent. It is further concluded that the difference in efficiency of use of aluminum by these two classes of blasting agents results from a higher contribution to useful work from the condensed detonation products of the relatively higher density aluminized slurry blasting agent.

Jan 1, 1981

By Robert L. Martin, Brian W. Stump

"The Black Thunder Mine is located in the Powder River Basin of Northeastern Wyoming. Over 39.2million tons of coal were produced at the Black Thunder Mine in 1996. Just over 100 million pounds ofANFO/Emulsion blend were consumed in that same year. Currently around 30% of the overburden is cast to final with the use of explosives. With plans for a mine expansion, explosives will continue to play a very vital roll well into the future."

Jan 1, 1997

It is a case study of huge rock-mass, loosened out from the parent rock-body, & posing a potential danger to structures down below the slope on which this rock mass was standing. Case was dealt in two phases, by tying/stitching the rock mass to the parent rockbody and breaking it using controlled blasting technique.

Jan 1, 1997

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By R. Franfield, W. J. Birch, L. Bermingham

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as consequence of the shock wave created by the detention of the explosive charge in a blast hole, rapidly propagating through the rock and then impacting on the quarry face.

Jan 1, 2013

By A. S. Tawadrous

The stress field around a detonating charge in a borehole was calculated using AUTODYN for a variety of in-situ stress conditions. Calculations were conducted for zero in-situ stress, hydrostatic conditions at 100MPa, uniaxial stress conditions of 100MPa, and bi-axial state of stress with amplitudes of 200MPa and 100MPa along the axes. Two different explosives, ANFO and emulsion, were used for the calculations. It was shown that in-situ stress fields had an effect on the tensile and compressional damage zones around the blasthole, calculated on the basis of the maximum amplitude of the stress pulses in the rock after the detonation of the explosive in the blasthole. The extent of compressional damage increased around the borehole, whereas, the extent of the tensile damage decreased. The damage zones are of elliptical nature with their axes parallel to the direction of the principal stresses. The difference between the major and minor axis of the elliptical damage was not very significant in the case of the compressional damage; however it was significant in the case of the tensile damage.

Jan 1, 2007

An explosive's velocity of detonation (VOD), can be used to indicate a number of important characteristics regarding the product's performance under specific field and test conditions. A number of new characteristic and transient VOD curves have been identified in the field, which can be used to evaluate explosive performance, control ground vibration amplitudes and frequencies, select the correct amount and type of stemming for use at the collar and in stem decks, eliminate explosive desensitization, evaluate primer performance, design air deck based blasts, evaluate contaminated explosives and to overcome post blast noxious fumes.

Jan 1, 1994

By Paulo Couciero

Since explosives are the source of all energy used for rock blast fragmentation and heave, multidimensional effects in the detonation driving zone become essential to better describe the detonation process. In order to use the explosive as an energy source-information for more realist blasting performance simulations, a simple and effective modelling strategy is desirable. Facing this challenge, an engineering approach to two-dimensional unconfined non-ideal detonation is proposed. Based on the elliptical construction of the shock locus, the model combines the axial cylindrical stick Q1D solution with some additional limiting conditions to determine the sonic edge of the charge. For a given set of rate law parameters and velocity of detonation, a complete axial solution is firstly computed through the Q1D model. From this solution, a vital relationship between the axial shock curvature with the shock shape parameters can be stablished. Once this relationship is found, the problem simply reduces in finding the shock shape parameters subject to the sonic edge condition. As a result of this calculation, the corresponding charge diameter can be found. Consequently, the proposed model can map the diametereffect curve by relating the unconfined velocity of detonation with its corresponding diameter. Finally, because of its low computation cost, the proposed engineering approach can be also used for characterizing the rate law parameters by fitting to data from unconfined detonation experiments

Jan 1, 2019

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By G Alan Foster

This paper discusses the cause of air blast and modern techniques to reduce this at the source. In addition it raises the problem of their marked variability due to prevailing weather conditions and how weather data can be obtained and used in the control of air blast.

Jan 1, 1975

By Inc. The HDH Group

The Alternative Risk Market is defined as the segment of the insurance market that is made up of self insurance, risk purchasing groups, risk retention groups and captives. It is commonly referred to as the alternative to the traditional market, even though more the majority of companies today are insured through the alternative risk market than the traditional market.

Jan 1, 2007

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By Tristan Worsey

This work was performed during the summer of 2008 during the junior year of a BS in Mining Engineering. It was observed that the mine was having a problem with back break during the blasting of development drifts. The unwanted back break was causing the mine extra costs in ventilation, ore dilution, ground support, back fill, explosives and man-hours. The blasting practices were observed for four weeks and the problems and their solutions were defined. In this paper the reasons and causes of the problem are explained with the proposed solutions to eliminate back break.

Jan 1, 2010

By Robert B. Hopler

Hercules Incorporated has designed, developed, and begun introducing a new non-electric delay blasting cap system which is radically different from anything presently available. This system, called Hercudet™, utilizes no wires or detonating cord. Instead, each cap has two plastic tubes attached to it. These tubes contain no coating or other materials other than dry nitrogen to extend storage life. In use, after connecting the tubes together with external sleeve connectors, the circuit is checked with a specially designed tester. When the blast area is cleared, the circuit is filled with a gas consisting of an automatically proportioned mixture of fuel and oxidizer gases. When the circuit is fully charged the gas is initiated by special means within the Hercudet™ blaster. The reaction that then travels throughout the circuit has no distruptive effect on the tubing, and virtually no noise is produced.

Jan 1, 1975

"In order to increase control over blasting, it is important to identify the imperative mechanismsand to quantify their participation during the rock fracturing process. The useful energyreleased by the detonation of an explosive is split into shock and gas energies. The relativeimportance of these two energies in the rock fracturing process is still an area of active debate."

Jan 1, 1999

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012

By Wang Xuguang, Kang Tingzhang, Zhang Xiaozhi, Wang Guoli, Li Ziqianga

Emulsion powder and granule explosive is produced through airflow fluidization technology by using W/O emulsion. Maintaining the microstructure of W/O emulsion, it has the advantages of both emulsion explosives, such as good water-resistance and detonation properties and powder explosives, such as low cost and east handling. The basic theory of emulsion powder and granular explosive, choices of constituents and formulation, technology for preparation, equipment and relevant parameters, product property as well as technology for safe use have been illustrated in this essay. Based on the above illustration, related factors influencing property and use result have been analyzed.

Jan 1, 2000

By Syed Haq, Kyle Optt, David Campo, Doug Anderson

Limitations on allowable levels of vibration from construction activities generally consider either annoyance or damage. While activities such as drilling and roller compaction primarily create annoyance, the major concern for blasting is usually damage. Many years of research have developed correlations between peak particle velocity and either threshold or structural damage. We emphasize the term “correlation” for two reasons. First, peak particle velocity is only a single-valued representation of a vibration waveform, and does not characterize it completely. Second, a given peak particle velocity by itself, even a particle velocity waveform, will not damage anything – strain does. Why not measure strain all the time? Strain is very localized, and can vary substantially over short distances, so choosing the appropriate strain measurement can be difficult. Measurement of strain is appropriate when either the behavior of a specific structural element is needed, or the overall response of a structure can be adequately represented by a well-selected strain measurement. We will discuss the appropriateness of both particle velocity and strain as deformation and damage descriptors, in general. We will also describe a specific case history, from a tunnel project in New Jersey, correlating strain with peak particle velocity. Finally, we will make recommendations for the choice of measurement type for some common situations.

Jan 1, 2004

By K. Hausmann, P. A. Sashin, G. J. Prejean

Misfires caused by unreliable shock tube constructions can have significant cost implications and place field workers at serious risk during remediation. Ionomer materials, used as a subtube in shock tube constructions, provide superior hot tack strength, oil resistance, impact resistance at cold temperatures and excellent thermoformability properties. These are important features for resisting blast-throughs and ensuring blasting reliability in demanding environments, such as open pit mining in harsh environments. Superior hot tack strength, strain hardening, and excellent thermoformability properties of the ionomer materials ensure uniform powder distribution along the shock tube during construction and avoid undesired powder accumulation due to deformation or vibration during use. Oil or chemical resistance is another feature of Ionomers. This allows improved property retention in contact with oils and hence longer sleep times of the shock tube. Another feature of these highly engineered ionomers is superior impact strength at low temperatures. This plays an important role considering the resistance to fly rock impact in open pit mining operations in particular in cold climates.

Jan 1, 2011