Search Documents

By M. R. Garmsiri

With the environmental issues and water recycling becoming more significant, the development of deep cone thickeners has improved the efficiency of thickening. While deep cones performance is dependent on many factors, the sensitivity of an industrial thickener to each variable factor has not been determined. In this work, four industrial deep cone thickeners, which are used on tailings stream in Shahrebabak Copper Complex, were monitored for a year to analyze the effectiveness of different factors affecting the performance. Feed flow rate, fine fraction of the feed, solids concentration, flocculant dosage and concentration, solids density, pH, temperature and bed height were the factors investigated on the basis of partial R2 and partial correlation. Results indicated that, with positive effect, feed slurry dilution affected the dewatering efficiency most sensitively. With a negative effect, the sensitivity of dewatering efficiency of deep cone thickeners to flocculant dosage was negligible. While, decreasing flocculant solution concentration had a considerable positive effect.

Sep 1, 2012

By S. Z. Khan, Veerendra Singh, Y. Rama Murthy, S. Prasad, Sunil Kumar Tripathy, Gajanan Kapure

"In this study, a low-grade ferruginous low-grade chromite ore was subjected to reduction roasting by using conventional heating as well as microwave heating. Sukinda chromite ore deposit contains majorly iron-bearing minerals as gangue phase. The magnetic susceptibility of these minerals enhances effectively after reduction roasting. Alteration of crystalline structure and magnetic property of these metals enables separation of low-grade ore by using magnetic separation. Conventional roasting studies by varying the temperature, time of reduction and reductant dosage were changed for low-grade ferruginous chromite ore. Similarly, microwave power, retention/exposure time and reductant dosage varied for reduction roasting studies under microwave environment. It is found that low-grade ferruginous chromite ore can be upgraded by reduction roasting and 61.2% Cr2O3 was recovered with a chromium-to-iron ratio of 1.93 from feed chromium-to-iron ratio of 1. Microwave reduction roasting studies resulted in upgradation of chromium-to-iron ratio to 1.73 with a recovery of 21% Cr2O3.INTRODUCTION The chromite ore occurs as a spinel containing oxides of chromium, iron, magnesium and aluminium. Most of the Indian chromite deposits are of ferruginous (rich in iron content) which indicates the abundance of ferruginous gangue minerals along with chromite. The primary use of chromite ore is towards the production of ferrochrome alloys. Chromite ores with less than 40% Cr2O3 and the chromium-to-iron ratio (Cr-to-Fe ratio) <1.8 is considered to be unsuitable for the smelting process (Tripathy et al. 2012, Tripathy et al. 2012a). A considerable amount of low-grade chromite ore and overburden excavated during chromite mining is getting accumulated every year, causing a threat to the environment. Its disposal poses a significant challenge and, hence, the beneficiation of low-grade chromite ore and its utilisation has been attracting a lot of attention. Different physical method of beneficiation methods is generally employed for the improvement of the Cr-to-Fe ratio (Tripathy et al. 2012, Murthy et al. 2011, Tripathy et al. 2012a, Tripathy et al. 2013, Tripathy et al. 2016, Tripathy et al. 2017, Tripathy et al. 2017a). It is observed that the enrichment of the chromite ore is carried out by using gravity and in some places by magnetic separation. However, the enrichment of Cr-to-Fe ratio from low-grade ferruginous chromite ore is difficult by using the above-mentioned beneficiation methods due to the presence of near gravity and near-magnetic susceptibility minerals along with chromite. However, an alternative beneficiation method is needed to explore for the beneficiation of such mineral deposits. Reduction roasting followed by magnetic separation is an alternative option for the separation of these types of ores which is widely reported for the iron and manganese ore (Li, et al., 2010; Chun, et al., 2014, Rath et al., 2018). These processes are majorly focussed on differentiating the magnetic susceptibility between minerals and subsequent separation by using magnetic field. The main advantage of such method is dry process option along with the pre-processed product for the costly smelting process. Also, the roasting of minerals in a microwave environment is also an active research topic in the recent time. So, the amenability of the separation feature of the roasting process by using conventional heating as well as microwave heating can be can be studied for the low grade ferruginous chromite ores."

Jan 1, 2018

By S. N. Shahcheraghi

Grinding is one of the most important and expensive steps in mineral processing allocating about 70% of the total energy in the plants. Nowadays, for optimizing the energy consumption in these equipments, the rock behavior and its size distribution during the crushing have been normally predicted using selection and breakage functions to be able to optimally model and design grinding circuits. For this purpose, the case of Miduk copper mine in Kerman province, Iran was studied. The samples were taken from primary ball mills feed and were subject to screen analysis to achieve uniform sizes. Then, selection and breakage functions were determined at the different grinding times in laboratorial ball mill. Finally, ore size distribution in different grinding times was estimated using MATLAB software

Sep 1, 2012

By Mohsen Hashemzadehfini

Nowadays heap leaching has become established as a mineral processing technology for treatment of some low grade minerals such as copper, gold, and zinc, etc. Heap height, particle size, leach reagent consumption, and metal recovery are four important metallurgical parameters in a hydrometallurgical process like heap leaching. This paper investigated the effects of heap height and particle size on copper recovery as well as acid consumption. Three heap heights of 2, 4 and 6 meters and two particle size fractions of less than 25.4 mm and 50.8 mm were selected as variables in the experiments. The research results showed the inverse relation between heap height and copper recovery as well as acid consumption. Under given conditions, the copper recoveries of minus 25.4 mm ore are 78.63%, 66.27% and 52.88% higher than that of minus 50.8 mm samples for the heap heights of 2, 4, and 6 m, respectively. Both copper recovery and acid consumption increase with decreasing particle size. Keywords: heap leaching, heap height, particle size, acid consumption

Sep 1, 2012

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Sep 1, 2012

By Yuexin Han

The wet preconcentration of haematite, comminuted by high-pressure grinding roller was studied, using the cylindrical ferromagnetic medium. The effects of various factors including rod diameter, rod gap and background magnetic field intensity (BMFI) on the performances of preconcentration for different size fractions and the force analysis of single mineral particles with different diameter in the separation zone were emphatically investigated. The results showed that as the rod diameter increased, the rod gap decreased, and the BMFI increased the tailings grade and the tailings yield reduced while the concentrates recovery raised that was regardless of variations in feed size distribution. For the -3.2+0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 7 mm at BMFI of 454kA/m is used to get a higher performance. For -0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 4 mm at BMFI of 263kA/m is used to get a higher performance. After the classifying preconcentration, at the optimum condition, the overall concentrate grade increases by 9.56 percentage points and the concentrate recovery is up to the 82.67% with a tailing grade of 10.68% and a tailing yield of 40.31%. The magnetic force, exerted on weekly magnetic minerals was proportional, to the specific susceptibility and square of BMFI. For the same BMFI, the magnetic capturing force on coarse particles increased, and that on fine particles decreased with the increasing of rod diameter. For the lean locked-particles, considering the gravity and viscous resistance of particles, rods with a big diameter were beneficial to the capture of coarse particles and had no influence on the capture of fine particles, while rods with a small diameter were good for the capture of fine particles and not suitable for the capture of coarse particles of lean locked-particles. Keywords: low grade haematite, high-pressure grinding roller, high intensity magnetic separation, pre-concentration

Sep 1, 2012

By Vasily V. Lodeischikov, Adolf F. Panchenko, Olga D. Khmelnitskaya, Vladimir E. Dementyev

Pilot plant tests of underground gold leaching from Maminskoye deposit oxide ores at a grade of 0,7 g/t Au were carried out. The underground leaching flow sheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution on active carbon, carbon concentrate ashing and calcine melting to produce high grade gold concentrate. The underground leaching system throughput was 15 m3 of solution per hour. Gold concentration in pregnant solutions was 0.12-0.13 mg/l. Gold recovery from solutions into carbon was in the range of 63-84%. It was demonstrated that the low Au recovery in the adsorption cycle was due to the presence in pregnant solutions of "active" chlorine, which destroys active carbon and causes a sharp decrease of the carbon loading capacity for gold. To improve the adsorption indices, previously dechlorinated pregnant solutions using bituminous coal or Na2S2O3, is recommended. Ion exchange process was tested as an alternative for gold extraction from dechlorinated solutions. In the testwork period, 4.4 kg of gold were produced with a chlorine consumption of 3.5 kg per 1 g of gold. During the tests a program of environmental protection measures was completed to provide the necessary safety precautions of the underground leaching works.

Jan 1, 2003

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By Lang Shiping

The criteria for designing a crushing chamber are presented and a program for designing the shape of the chamber is proposed. During the chamber shape design, major design parameters are analyzed first, optimized parameters are determined next and the basic shape of chamber is figured out finally. In the basic chamber design program, the influence of abrasion of basic chamber shape and material characteristic are not accounted for usually. Here, based on the minimum abrasion of chamber shape and uniform particle size theory, the equation for chamber surface curve and the transcending function were formulated and a low-abrasion chamber was designed. Since the chamber shape designed based on experience and experiments is not necessarily the best, optimal design of the crushing chamber shape was carried out. Cubic spline function was used to represent the chamber shape curve and a mathematical model was formulated. The optimal shape solution was obtained using a complex method. Finally, the optimal chamber shape was determined by matching the moving cone stroke S, moving cone speed N and the moving cone bottom angle Thus, superior technical performance of the cone chamber was achieved.

Sep 1, 2012

By M. Gonzalez Fernandez

"If the final goal of metallurgy is the extraction of metals from a given ore, everyone knows that this achievement relies on many separation steps involving much more than a biphasic material made of metal and gangue. Nevertheless, still today, most of the design and follow-up of industrial processes only consider metal grades; in best case metal grades per size class. Working with such heterogeneous material, made of several minerals, with different grain size and texture, implies to consider finer ore models to be able to predict the behavior of material and the subsequent operation performances. Analytical tools are now available to provide such relevant and accurate data which are applied in geometallurgy. To achieve a true geometallurgical approach for process design, but also for optimization, accurate process simulation absolutely needs to combine these fine ore models with the corresponding unit operation models. Based on generic, but configurable, criteria of description and a hierarchical approach, the material modelling tool embedded in the USIM PAC process simulator provides the necessary flexibility to describe any type of ore with almost no limit in the level of details and associated physical properties that can be met in the mining industry. The simulation engine and the mathematical models of unit operations are designed to manage such a diversity of material modelling. The paper present various ore models and some of their applications in flowsheet simulation. It proves the interest of this detailed and advanced approach to accurately predict plant performances. INTRODUCTION Process simulation used for process design and optimization requires accurate unit operation modeling. During the last decades, main efforts of the different teams developing software simulators have been dedicated to those models for comminution and physical separations such as flotation or gravity concentration (Kojovic et al., 2012, Soni and Yoon, 2014). In most case, the ore is modelled with a size distribution and metal or mineral grades. A water phase is considered for wet processes. The association of unit operations and such material models generally allows, after some parameters adjustment, to achieve good agreement between experimental and simulated data. The use of the obtained simulator to test alternative configuration of circuits or settings of equipment devices can be accurate enough as far as the ore processed is close to the ore used for simulator adjustment. However, when the ore gets very different grades, coming from different mineral proportions or grain sizes, the simulation results can be of poor accuracy. Because any physical separations such as gravity, magnetic or flotation, do not sort metal and gangue but particles, made of minerals, containing metals, the only way to be accurate enough for allowing extrapolations, is to model particles. The phase model tools embedded in the USIM PAC process simulator gives this possibility. However, as such level of details are not always available for analyses, the tool has been designed with a high level of flexibility, to adapt the model to the available data. In this paper, the principles of this conceptual modelling tool are presented, and some application cases illustrate the material model flexibility and its interest."

Jan 1, 2018

By P. T. L. Koh

The effect of particle shape on the flotation process has been investigated in laboratory experiments with monosized spherical ballotini and roughly ground ballotini. The particles were treated by partial methylation with trimethylchlorosilane to achieve varying degrees of hydrophobicity. In flotation, the process of film thinning and liquid drainage is critical in the formation of a stable bubble-particle attachment and this is affected by the particle shape and surface hydrophobicity. The rate of attachment affects the overall flotation rate. Flotation tests with different particle sizes at various degrees of partial methylation have been performed in a modified Denver cell. Predictions from a computational fluid dynamic model of the cell which incorporates fundamental aspects of bubble-particle attachment are compared against flotation test results. Contact angles of the particles have also been measured using the capillary rise technique to indicate surface hydrophobicity.

Jan 1, 2014

By James A. Finch, Linda Restrepo, Mitra Mirnezami, Amy Buchanan, Maryam Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally reveals two aggregation maxima at pH 8-10 and 10-12 (Figure 1). From measurements on sphalerite and silica suspensions the double maxima could be replicated. These maxima correspond to the effects of Zn and Mg ions. The aggregation mechanism of both ions is related to the formation of the corresponding hydroxide precipitate. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By ?. Kostadinov

Theoretical study of the behavior of grinding medium presented by TBP (tetraballpebs) was conducted by computer modeling of the position of grinding medium at different speeds and different drum fill factor. For the modeling were used known equations of motion derived for the ball load. Algorithm was created by SolidWorks software, allowing determination of center of gravity of the load in the mill and energy for grinding. These results were compared with similar results obtained by ball grinding medium. The capabilities of both grinding media are demonstrated by graphics under the following conditions: 1.Equal dimensions of the experimental model of the mill; 2.Equal mass of the grinding loads; 3.Comparison of grinding bodies with the same number, mass and density. Keywords: simulation, behavior, grinding medium, balls, tetraballpebs

Sep 1, 2012

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

The concept of the Unified Comminution Model (UCM) was presented at the 23rdIMPC. The model utilises computational techniques to calculate the mechanical environment in any comminution device, and then incorporates the outcomes from rock breakage tests to predict the product from a device. The model is fully mechanistic, and incorporates the capability to simulate novel equipment. This paper presents the progress on the first application of this concept to applied comminution equipment. This novel comminution model aims to integrate all comminution models within a single struc-ture. This will provide a step change in the predictive power of comminution models, and include a wide range of particle properties that will enable it to be linked to the upstream and downstream process of mining and recovery. Major advances over current models will be the capability to predict liberation, preferential grinding, performance of new and novel devices, and to have power as an integral driver of the comminution simulation process. The methodology and model structure have been developed. An equation within a population balance framework has been derived as the basis for the UCM. A set of SAG mill pilot has been used as the first test case. The breakage characteristics of the ore have been extensively tested utilising a new range of breakage tests required by the rigorous UCM structure. The mill was simulated with the EDEM - DEM software. A partial test simulation of the pilot SAG mill has been conducted. This serves to demonstrate the feasibility of this modelling technique, but still lacks important ore characterisation components that are under development. The study has raised a number of significant challenges to the accepted understanding of the comminution process. Through addressing these challenges considerable insight has been gained into the energy environment in mills and the requirements of breakage testing. The ore characterisation methods and energy transmission derived from DEM simulations remain as major research items.

Jan 1, 2014

By Güven Önal, Zeki Dogan, Neset Acarkan

"In general, the processing of glass sand may involve comminution, washing, wet classification and attrition scrubbing. Additional processes may include magnetic separation, flotation and leaching in various combinations.Yaliköy sand dune deposit is located near to Istanbul on the European side by the Black Sea coast. The reserve of deposit is around 70 million tons. Iron content of Yaliköy sand dunes is 0.48 % Fe2O3 and not suitable for glass manufacture. The iron content of glass sand should be less than 0.15 % Fe2O3 for window glass manufacture and 0.05 % Fe2O3 for glassware. In this study, it was aimed to produce glass sand with less than 0.15 % Fe2O3 for window glass and with less than 0.05% Fe2O3 for glassware manufacture from Yaliköy sand dunes. A representative sample with a weight of 200 kg was taken from Yaliköy sand dunes deposit through opening small pits.• Mineralogical studies have shown that iron is present in three forms:• Hematite, limonite, clay and iron silicate minerals such as epidote and garnet occur in free form.• Quartz grains are coated by hematite and limonite.• Iron is also present in the cracks of quartz grains.Free iron minerals such as hematite and limonite and silicate minerals were subjected to magnetic separation and flotation for removal. Iron coatings were tried to be removed by scrubbing and leaching. Iron removal in the cracks of quartz grains was attempted by grinding and leaching.Under optimal conditions, sand concentrate with 0.38 % Fe2O3 was obtained by means of high intensity disc type magnetic separation. Grinding and scrubbing were applied to see the effect of size reduction and attrition at room temperature and 90 ºC, by using non-magnetic fraction. Sand concentrate with 0.13% Fe2O3 was obtained at 90 ºC in this test.Sand sample which was previously ground to minus 0.5 mm and scrubbed, was floated by using sulphonates as collector. After flotation tests, sand Concentrate was obtained with 0.11 % Fe2O3.The optimum iron removal was achieved by H2SO4 leaching at 90 ºC depending on acid concentration and leach duration in static, percolation and agitation leaching. Agitation leaching was done by the use of mixer at 600 rpm, 50% solids and leach duration was 15 minutes."

Jan 1, 2003

By A. Tolentino, J. Bravo, M. A. Corona-Arroyo, C. Quintero, R. Zarate, A. Lynch, L. Carillo

"This paper presents the performance of the flotation circuit of Minera Fresnillo PLC, Mexico. A plant survey was carried out on the lead banks and a size-by-size assay on the samples was conducted. The results indicate that the plant is treating fine particles in the flotation circuit. At least 30% of the particles in the feed are finer than 8 microns and that high amounts of Pb, Au, Ag and insolubles are in this particle size. It was also found that higher percentage of insolubles in the -8 micron particles are recovered in the final concentrate rather than being rejected in the tails. The presence of high amounts of insolubles in the concentrate is an issue of the company. The result of the plant survey provided valuable information for effective reduction of the insolubles in the concentrate and for plant optimization. The work conducted is part of the training of the students involved in a mine placement in the Alban Lynch Student Venture. INTRODUCTION Minera Fresnillo is one of the operating mines and the main contributor to the silver production of Fresnillo PLC group, the world’s leading producer of silver from ore. It is located in the mining district of Zacatecaz, Mexico, approximately 650 kilometers from Mexico City. The major minerals that make up the ore are galena, sphalerite, tetrahedrite, pyrargyrite, proustite, polybasite, pyrite and pyrrhotite. Minera Fresnillo has a capacity to treat 8300 tonnes of ore per day. The plant consists of semi-autogenous mill - ball mill – hydrocyclone circuit for primary grinding followed by silver-lead flotation then zinc flotation circuits. This paper reports the plant audit conducted in the silver-lead flotation circuit (Figure 1) of Minera Fresnillo. The circuit includes rougher, scavenger and two stages of cleaning. The tails from the scavenger goes to the zinc flotation circuit while the second cleaner yields the final silver-lead concentrate. The feed to the circuit has a particle size of 90% finer than 75 microns and generates a concentrate with grade of about 35% Pb, 5700 g/ton Ag, 16 g/ton Au and recoveries of 90% Pb, 90% Ag, 64% Au, respectively. Although the plant achieves their target concentrate grade and recovery, the concentrate also contains significant amount of insoluble materials which is about 18%. These insoluble materials consist of gangue minerals. The plant audit was conducted primarily to determine the possibility of further reducing the amount of insoluble materials present in the silver-lead concentrate."

Jan 1, 2018

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place. There are two possible mechanisms describing this process:(a) Gas nucleation, caused by nano bubbles inside the film.(b) Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals).Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film."

Jan 1, 2003

By Jia Ma, Zhi-Chao Liu, Kang Liu, Chun-Feng Li, Bao-Bin Tang

"The geological environment of the certain uranium-molybdenum deposit is very complicated. While the study of process mineralogy is relatively few, which restricting the processing and leaching effect of ores. According to reaserch on process mineralogy of this mine, the basis of ore processing can be provided. The main contents of research are the uranium occurrence state and the influence of H2O2 in acid leaching. By various methods and experiments, the process of uranium mineralogical characteristics in this deposit are systematically studied. The results show that the uranium is mainly in the form of independent uranium minerals. The structures of these uranium minerals are venous and disseminated in mineral fissures, or microgranular inclusions in quartz and feldspar. It is not appropriate to concentrate the uranium minerals by flotation beneficiation because that the loss rate of target metals via water leaching process is very high. The ores are suitable for being acid leaching directly with 6% – 8% of H2O2, and the maximum leaching rate of uranium can be 96.88%. INTRODUCTION The uranium ores with associated elements have a large proportion in uranium resources (Lei, et al., 2014, Xing, et al., 2006; Ritchy and Wong, 1985). The uranium and molybdenum are easy to be paragenesis in nature enviroment because of their similar chemical properties. Therefor the uranium-molybdenum associated deposits are widely existing, such as the sedimentary sandstone uranium deposit in American with vanadium and molybdenum, the sedimentary sandstone uranium deposits in French with vanadium (Chen, et al., 2014; Lounis, 1997). A certain epithermal porphyry uranium-molybdenum deposit in China is mainly controlled by the subrhyolite- porphyry and the fault zone (Lv, 2012; Rui, 2010; Liu, et al., 2010). The ore properties of this deposit are complex, which include the high alteration degree, and the fine grain size of the target minerals (Ma, et al., 2013). The ore properties and occurrence state are quite different during each mining stage. As a consequence, the consumption of reagent increased and the leaching rate declined as long as the continuously mining. The author explored the best leaching rate of target elements According to the basic research on process mineralogy of present ores, experimental study of water leaching and oxidizing acid leaching on different particle sizes."

Jan 1, 2018

By W. S. Eu

Thermal treatment of mineral ores can initiate thermal phase transformations which can affect either their activation or deactivation, subsequently influencing their ability to dissolve in a leaching reagent. The formation of rutile and hematite from ilmenite minerals, for example, has been suggested to occur through a series of reduction and segregation reactions. This process has been used in beneficiating low-grade weathered ilmenite ores to higher grade rutile. Despite decades of re-search, the mechanism of this process is not well understood, because dissolved intermediates are poorly crystalline and are difficult to quantify, with the exception of the final rutile products. Previous studies have shown that disrupted intermediate phases, by thermal treatment, are most susceptible to reagent attack and can often demonstrate ?activation? effects. In this study, synchrotron based X-ray diffraction method was used to investigate in-situ and in real-time the transformation of ilmenite minerals to rutile and hematite during calcination. The rate of formation and disappearance of specific Bragg peaks during the reaction and thermal decomposition of the mineral were used to derive an understanding of the solid-state reactions. The effects of the mineral transformation were validated by laboratory based batch calcination and leaching in sulphuric acid. The results suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014