Search Documents

By J. E. Moran

A groupd of French capitalists, La Compagnie Française des Mines d'Or du Canada, has undertaken the considerable task of developing Otter creek, in the Atlin district, B.C., by hydraulic mining methods. It has long been known that the gravels of this stream carry sufficiently high values in gold to make it attractive as a mining venture, but it was impossible to ignore the existence of formidable natural obstacles to hydraulicing them, and these needed to be taken into serious account before embarking upon any costly programme of development. The tide to the Otter Creek leases was originally held by Mr. H. Maluin, a French engineer well known throughout the north, to whom was to fall the task of financing whatever programme might be decided upon. It was he, too, who would have to assume the responsibility of finally passing judgment upon the practicability of the various devises for overcoming the adverse natural conditions. With an infinite attention to detail, which I believe to be a characteristic of the French people generally, he studied his problem and was finally able to submit to his financial backers a programme which left the very minimum possible to the hazard of accident or chance. Dr. Mandy, on his visit to Otter creek this season, expressed the opinion that our method of opening this difficult creek presented certain features which might be successfully applied in placer operations elsewhere in British Columbia, and it is largely for this reason that the present paper has been prepared. I shall set forth, as well as I can, the practices which have enabled us to overcome rather easily some of the obstacles which nature had unkindly placed in the path which we must take. The natural flow of water in Otter creek is far too little to deal success-fully with the rather excessive amount of glacial drift overburden which lies directly over the gold-bearing gravels. For this natural defect, the only remedy was to procure more water. This we have clone through a system of flumes and ditches, totalling between ten and eleven miles in length, which bring to the mine a supply of water adequate for our needs.

Jan 1, 1932

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By C. Sist, J. Shannon, J. Fossenier, J. F. Adams

With the cleanest and easiest to treat copper concentrates dwindling and becoming harder to find, electrorefineries must deal with the reality of higher impurity anodes. There are well-known strategies for managing nickel, bismuth, antimony, etc. using bleeds (Ni, Bi, Sb, As) or arsenic control (Bi, Sb) or hydrometallurgical add-on circuits (IX, MRT, SX for As, Bi, Sb). However, for integrated copper producers and those producing other base metals it is often worth considering a more holistic, global approach. This paper will discuss both the well-known strategies as well as some global strategies and the role that hydrometallurgy can play in them. Examples will include atmospheric and pressure leaching, selective precipitation and impurity recycling or fixation. INTRODUCTION In the electrorefining of copper, impure copper anodes are electrically corroded, and pure copper is deposited on cathodes by passing DC current through an acidic copper sulphate solution. The anode copper impurities either settle to the cell bottom as insoluble components (anode slimes) or remain in solution with minimal deposition at the cathodes when correct operating parameters are maintained. Consideration of impurities is important in all copper electrorefineries. A typical impure anode contains 98.5–99.5% copper (Schlesinger et al., 2011). Table 1 shows the range of impurities reported for all copper anodes in the 2007 survey of operating refineries (Moats et al., 2007). Also shown is an approximate “limit” of anode compositions within which the majority of refineries operate without additional impurity removal capacity (beyond conventional liberator/bleed circuits). The column is somewhat subjective and meant to be an approximation only since there are many factors that influence impurity deportments and refinery impurity tolerances. More recent world survey data from 2013 show the averages for all impurities trending upward from 2003 to 2013 (Moats et al., 2013). With a competitive market for good concentrate and more copper recycling from electronics (which contain high levels of impurities such as nickel, lead and antimony), this trend is expected to continue through the coming years. The traditional primary method of impurity control is refinery bleed through liberator cells which are employed in the vast majority of refineries (Moats et al., 2013). These are used to control copper (primary liberators), nickel, arsenic, antimony and bismuth (secondary and tertiary liberators). Other methods of impurity control include arsenic addition (upstream in the smelter deporting to anode or directly to electrolyte) to control antimony and bismuth (Kamath et al., 2003), ion exchange or molecular recognition technology (Hur et al., 2005; Navarro et al., 2012) for antimony and bismuth. Many refineries also operate nickel evaporators to remove nickel sulphate before recycling back acid. Some use, or are contemplating using, acid purification units to recycle acid and arsenic without nickel and making nickel carbonate (Kamath et al., 2003; Sheedy et al., 2006).

Jan 1, 2019

By B. R. Schneiders

"Atikokan is 200 km west of Thunder Bay and earned its mining fame from the discovery of the Steep Rock Iron Range in the late 1930s. Gold, however, was discovered in the Atikokan and Mine Centre areas in the late 1800s and eventually led to one of Ontario's first gold camps, and a total production of approximately 52,000 oz of gold and 174,000 oz of silver from 218,000 tons milled.The general geology of the area consists of Early Precambrian rocks of the Wabigoon and Quetico subprovinces, separated by the east-trending Quetico Fault. The Wabigoon Subprovince, to the north, consists of metavolcanics, minor metasediments and granitic batholiths. The Quetico Subprovince consists of metasediments and granitoids. Small ultramafic plutons occur throughout the metasediments.Within a 50-km radius of Atikokan, more than 50 gold occurrences, prospects and past producers have been discovered since the 18oos. The Atikokan Gold Study performed by the Ontario Geological Sur vey (Wilkinson, 1980, 1982) defined three types of gold mineralization in which gold is concentrated in quartz and quartz-carbonate veins:I) Metavolcanic-Hosted, Stratabound Type-associated with altered felsic fragmental units and chemical sedimentary rocks; possible gold mineralization source rocks. The mineralization is due to metamorphogenic (epigenetic) enrichment. Associated with dynamic metamorphism events and/or felsic intrusive events.2) Marmion Lake Batholith Type-occurs within the gneissic core of the batholith associated with north east-trending lineaments, representing faults or shear zones. Mineralized veins are related to several periods of deformation and shearing, suggesting that metamorphogenic veins were produced during dynamic metamorphism.3) Contact Zone Type -occurs in the contact zone rocks between gneissic batholiths and meta volcanic belts. Hydrothermal solutions produced during several deformational periods acted to leach and concentrate gold mineralization. Localized, discontinuous shear zones host the epigenetic (metamorphogenic) veins.Twenty-one properties in the area were mapped and sampled, and researched petrographically and geochemically. Geological data from the Atikokan Economic Geologist Program of the Ontario Geological Survey are used in discussing the types of mineralization, genetic models, and exploration targets and techiques."

Jan 1, 1983

By Nick Vayenas

This paper discusses the application of a commercially available state-of-the-art PC discrete-event simulation modeling software, called Promodel, for simulating a typical underground mine hoist system in the Sudbury mining region, in the province of Ontario in Canada. The reasons for using Promodel as a two-dimensional simulation development tool is its simplicity in use and its capabilities to provide enough flexibility to meet the modeling requirements of a mine hoist system. General information of a mine hoist system was collected for building the model. Example of the model?s output is also presented. The application of Promodel in underground mining offers a powerful, two-dimensional simulation environment in an affordable price for mining engineers to analyze and study operational problems. This hoist simulation model is an intuitive demonstration of the mine hoisting elements and the operational logic of the hoist, based on which optimization of the entire mine system materials flow can be considered as part of a mine cycle management feasibility study.

Oct 1, 2009

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved

Jan 1, 1979

By R. Butar-Butar, J. Mosher, G. Banini, J. Hollow, A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia’s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

At 14%, the representation of women working in the mining industry is the lowest among primary industry categories in Canada1. With reference to mining operations and senior leadership, the gap in the industry is even more pronounced. In an effort to narrow the gender gap, recent industry, education, and policy efforts have been made to increase the number of women entering the industry through career awareness and early career recruitment strategies. These strategies implied that by increasing the numbers of women entering the industry there would be a natural progression of women into the hierarchies of organizations. Efforts to retain women in the industry have focused around removing career barriers such as reviewing flexible work practices and programs directed at work life balance. At this time, these efforts have resulted in negligible fluctuations to the gender gap within the industry. This research investigates the under-representation of Highly Qualified Women (HQW), and the interaction of workplace culture on their career advancement and retention within the industry. HQW (women with a bachelor?s degree or higher) are the focus of the work as they represent an essential source of leadership and technical capacity for mining organizations. This paper is based on the results of a survey of 170 HQW working in the Canadian mining sector. The findings from this research suggest that HQWs careers in mining are stalled, despite a strong indication by respondents of interest in their professional career advancement. With regards to workplace culture, respondents indicated that blatant forms of gender discrimination have been reduced in mining workplaces; however, exclusion from informal networks, implicit bias and subtler forms of workplace discrimination persist. Utilizing a framework to assess the workplace culture for women in attracting and retaining their employment, respondents provided detailed information on the aspects of workplace culture that are most problematic in relation to women?s career development in mining. Women consistently identified problematic workplace culture as a significant barrier to the career advancement and retention of women within the industry. The representation of women within the labour force will likely remain stagnant until the industry addresses workplace culture within the industry, and makes strategic efforts to develop inclusive cultures throughout mining and supportive organizations.

Aug 1, 2013

By R. Mohamad, J. Asfahani

Abstract - Radioactive characteristics of pits drilled in the Al-Sharquieh mine while prospecting for recent phosphatic resources have been investigated. The results indicate that phosphatic layers are characterized generally by high radioactive intensities (more than 800 c.p.s). The lithological section in the study area is very complex sedimentologically, and characterized by high faciological variation in all directions. The Schlumberger geo-electrical configuration with fine separation of AB/2 was successfully applied to determine lithological boundaries, and the resistivities of the layers of the lithological section, especially for thin layers. It was shown that the phosphatic layer resistivities increase or decrease as a function of associated material. As a result, two types of phosphatic layers have been geo-electrically distinguished. The first is characterized by high resistivity and relatively low radioactivity, which could be related to the rock phosphatic layers. The second is characterized by low resistivities and high radioactivity, which could be related to the sandy phosphatic layers.

Jan 1, 2000

By L. Xu, A. Vazirnegad, R. Bhaskar

"Respirable dust samples are collected by the U.S. Mine Safety and Health Administration (MSHA) and mine operators as part of the requirements of the Federal Coal Mine Health and Safety Act of 1969. About 1.85 million respirable dust samples collected by MSHA were analyzed for the period 197/ to 1990 f or the states of Alabama, Colorado, Illinois, Kentucky, Ohio, Pennsylvania, Utah, Virginia, and West Virginia. Trends in coal dust exposure of continuous miner operators, helpers, and roof bolters were analyzed. The reported production in each of the nine states was analyzed. The relationship between average dust exposure and coal production was evaluated. In addition, the differences between mine operator and MSHA inspector collected data were examined for each state. The average exposure levels for the three occupations - miner operator, miner helper, and roof bolter were also compared.The data indicate that the dust exposure levels have significantly dropped over the last twenty years, while at the same time production has increased, attesting to the ability of the U.S. mining industry to adapt successfully to the stringent dust control regulations. In terms of coal production, it appears that some states, such as Utah, Illinois, and Kentucky, were able to increase their production significantly relative to others, such as Pennsylvania and Virginia. The relationship between dust concentration and coal production is, at best, tenuous. 11 implies that existing dust control technology has assisted several mine operators to meet dust standards, while, at the same time, enabling mines to produce more coal than before. Comparison of data collected by MSHA and mine operators indicate that MSHA inspectors recorded higher dust levels and lower shift production relative to mine operators."

Jan 1, 1993

By G. W. Zhang, Changsha Research Institute of Mining and Metallurgy, X. Xiao, Y. Long, L. L. Huang

"The paper presents a scale-up and design method of vertical screw stirred mill, in which the closed circuit of mill and hydrocyclone was assumed as one factor, theoretically regardless the affects inside system of the mill and hydrocylone. The specific energy is chosen as a scale-up criterion, based on the premise that when fed the same feed material, mills of different sizes delivering the same specific energy will yield products.Batch grinding tests are conducted to determine the specific energy, and combined with industrial production data, scale-up and design of vertical screw stirred mill for industrial production are accomplished. Having developed this method for the vertical screw stirred mill used in regrinding duty of iron ore in Ma Steel, it has now been successfully applied in other installations.INTRODUCTIONThe Towermill was developed in Japan in the 1950s, by the Tower Mill Kubota Corporation, it was fine and ultra-fine grinding mill of the metallic ores and concentrates. Due to the rapid development of metal mining and useful minerals disseminated fine, fine grinding and ultrafine grinding equipment has also been more wide used in minerals processing industry. Typical fine and ultra-fine grinding mil are the Vertimill and Stirred Media Detritor (SMD) Mill of Metso, Eirich Towemill, Outotec HIGmill, FLSmidth VXPmill, Xstrata Isamill and the vertical screw stirred mill (JM) of CRIMM, etc.JM series of vertical screw stirred mill were invented by Changsha Research Institute of Mining and Metallurgy in the 1980s. Energy saving and consumption reducing have been achieved through the optimization and engineering practice. More than 500 units JM series of vertical screw stirred mill are used in the iron ore, copper ore, copper-molybdenum ore, molybdenum ore, Pb-Zn ore and Au ore."

Jan 1, 2016

By C. Sartain

In recent years market pressures have been building on companies to develop the next era of mining projects to follow the previous boom in copper projects of the mid 90's. However the response from the industry has been slow in coming, and somewhat muted. It is clear that there simply have not been the obvious quality projects waiting to be rapidly developed. Many of the known undeveloped copper projects have particular characteristics that have previously prevented their development, including mineralogical complexity in the ore bodies, environmental challenges or particularly difficult geographic locations. This paper describes how the Copper Division of an international mining company, Xstrata plc, is preparing to progressively develop an impressive pipeline of projects, armed with an array of proprietary technologies and with a strong approach towards sustainable development and community engagement. The approach being taken is enabling Xstrata to complement its acquisitive corporate philosophy with a management emphasis on project development and operational optimization and enhancement.

Jan 1, 2007

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By P. Reyes

The Codelco Chile El Teniente Division Caletones Smelter has an objective to smelt 1,250,000 tonnes per year of copper concentrate. This is a great challenge for the smelter facilities and particularly for the acid plants. The analysis ensuring that there are no obstacles to achieve the production capacity was of great importance. Therefore a series of activities were undertaken as well as studies dedicated to reach the target. This paper presents work focused on a fluid dynamic study, translated in an operation methodology of integrated handling of the smelting and converting gases with the objective to optimize the gas flow and S02 concentration. The optimization should be done employing the current installations, equipment and instrumentation and/or minor modifications. In the first part of the work the condition of the instrumentation involved in the gas handling was checked, improvements determined and the corresponding corrective actions were carried out. The proposed operation method consists of operation of the Cleaning Gas Plant 2 (TC' s gases) and operation of Gas Cleaning Plant 1 (the remaining gas plus the gases from CPS). The implementation of the operation method involves the modification of the valve of the gas into the duct to plant 1 from On to Off to modulate flow. After modification a three days test was carried out. To evaluate the tests, a "Sulphur Capture" indicator was used. During the test the behaviour of the effluent treatment plants was closely examined. No problems or unusual operating conditions were observed. The reduced flow of gas to Gas Cleaning Plant No. 1 permitted the start up of the 2nd test day treating most of the gas received by Gas Cleaning Plant No. 2. The operation was carried out with the limitation not to increase the effluent pond level, which was maintained constant.

Jan 1, 2007

By F. S. Hoseinian, M. Irannajad, M. Safari

In this study, the effect of chemical interactions of materials used in ion flotation on the removal of Ni(II) ions from low concentration synthetic wastewater was studied. Sodium dodecyl sulfate (SDS) and ethylhexadecyldimethylammonium bromide (EHDABr) as collectors and methyl isobutyl carbonyl (MIBC) and Dowfroth250 as frothers were used. To investigate the effective parameters and interactions of them, 16 experiments including 6 level variables were performed by supporting DX7 software and on the bases of 2-level factorial method. In the first step, the tests were conducted in a Hallimond tube. The result showed that collector of SDS and frother of Dowfroth 250 had appropriate interaction with each other at pH = 3. In the second step, optimal results from the first step were evaluated in a mechanical flotation cell. The removal of Ni(II) ions increased by increasing the time of flotation and they have a direct relation with the water removal. The kinetics study shows that the order and the rate of removal of the reaction do not follow any of the zero-order, first-order and second-order equations. The flotation rate curve on the removal of Ni(II) ions will divide the separation process to two stages, a fast flotation rate at the first stage and a slow flotation rate at the second stage. Ni(II) ions removal was obtained 88% at the best condition.This study showed that the use of ion flotation was a very effective method for Ni(II) ion removal from industrial wastewaters.

Jan 1, 2016