Search Documents

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968

By McNeely DuBose

INTRODUCTORY PROSPECTING for aluminum has always been, and still is, a peculiar combination of the technical with the physical approach, and 1 want to explain my conception of the term 'prospecting' when applied to aluminum, which differs in some respects from the ordinarily accepted idea of prospecting. In the early days of gold mining, prospecting was a search in the hills and the river beds for the metal, not for its chemical combinations. And so it was in the early days of aluminum, with the difference that the search for the metal was carried on, not in the hills and dales, but in chemical laboratories. Aluminum is never found in the elemental state and at that time the metal bad never been seen, but scientists of that day bad forecast that such a metal must exist and in 1807 Sir Humphrey Davy went so far as to give this unseen metal a name, aluminum, from the Greek word alumen. This word applies to our alum, and it was from alum that Davy sought to produce the metal. It is strange to think that, in laboratories throughout England and on the continent, prospecting for aluminum was busily under way by men who had never seen the metal they were searching for. Their situation was something like that of the fisherman and the 'big one' that got away. They could describe the metal, give its exact weight, and even name it, but they could not produce visual evidence of its existence. Eventually, however, the efforts of the scientist 'prospectors' were rewarded and in 1826 the metal was actually produced, possibly first by Wohler, though Oerstedt, a Danish chemist, is usually credited with the achievement.

Jan 1, 1951

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By M. A. Halim, V. I. Lakshmanan, Z. Jankovic

An innovative mixed-chloride process for the separation of iron from lateritic ore is described. The separation of Fe(III) from leach liquor is an important process step for the recovery of nickel and cobalt. The patented process of Process Research ORTECH Inc. uses a lixiviant containing hydrochloric acid (HCl) and magnesium chloride (MgCl2) for the leaching of lateritic ores/concentrates followed by the selective solvent extraction step of Fe(III) over other value metals such as Ni and Co. The use of MgCl2 increases the activity of the hydrogen ion in the lixiviant, which reduces the consumption of HCl in the leaching stage and enhances the formation of HFeCl4-, thereby increasing the solvent extraction efficiency of Fe(III) with ketone. The process produces high purity iron oxide (Fe2O3) and regenerates HCl by the pyrohydrolysis of the FeCl3 rich pregnant strip solution. The developed process flowsheet is in closed loop, economically attractive and environmentally friendly.

Jan 1, 2015

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By Julie Q. Shang

The electrokinetic (EK) technology for dewatering of two tailings from the uranium mines in Northern Saskatchewan is studied in bench scale experiments. The study includes four phases: 1. Characterization of two uranium mine tailings; 2. Assessment of voltage loss on the coated Ti anode and water interface. 3. EK cell test series to measure electrokinetic permeability (ke) of two tailings; 4. EK dewatering test series to study electrokinetic enhanced gravity dewatering on two tailings samples. The results have demonstrated that both tailings responded positively to the EK process. For the tailings containing gypsum, the EK dewatering should be a short term process (within one hour) with anode conditioning (pH adjustment). The tailings containing clay minerals responded well to EK dewatering, in which pH adjustment is optional and will further enhance the EK flow. Both tailings as tested have low hydraulic conductivity and are particularly suitable for EK dewatering and consolidation.

Aug 1, 2010

By Hervé Toubon, Matthieu Davrinche, Jim Corman, Mamane Bello Boubacar Kinassa, Pierre Amadieu

Orano Mining maintains a significant level of Innovation and Development Research for its sites in Canada, Niger, Kazakhstan, Mongolia, and France. This effort is formalized within the six major thematic programs below, which include more than one hundred affiliated R&D projects:  Geological understanding, tools and methods for exploration  ISR technology (geology, modeling, mining development tools)  Mining technology (SABRE)  Ore treatment and processing (in particular via our Centre for Innovation for extractive metallurgy, CIME)  Environment (radiochemistry, modeling, tools and methods for remediation)  Digital Mine (sensors, transmission, database, and data modeling) This paper describes the main actions of these six programs, their stakes, and their progress. There is no single path leading to innovation but fostering an innovative context and a structured project approach are essential ingredients to successful development and industrial deployment. As a result, Orano Mining has, over the years, developed a disciplined methodology for R&D portfolio and project management. This methodology, presented here, targets a reduction in time to implementation while valuing both the expertise and the work in project mode.

Jan 1, 2020

By R. W. Nice

Presently about 60% of the world's nickel resources are tied up with lateritic ores while about 25% of the world's nickel is produced from sulphides. Based on this the industry has to focus on improving lateritic nickel economics in order to maintain the high use of the metal worldwide. In 1997 three junior mining companies in Australia organised finance against all odds and commenced development of three separate nickel and cobalt extraction plants treating lateritic nickel ores. All three projects utilise similar pressure acid leaching (PAL) technologies while each has unique metal recovery technologies All projects have experienced numerous processing and maintenance related difficulties such that full ore throughput has been reached by only one operation after five years. This shortfall in performance has caused the owners considerable angst and financial pain. In 2000 Cawse went into receivership and was purchased by an international corporation. Recently, Bulong also went into receivership and has undergone an orderly shutdown, awaiting sale to a new buyer. Murrin Murrin has settled with its financiers and is in a position to operate as planned for many years forward. This paper will discuss a number of the technical difficulties that affect the ore preparation, PAL and solution treatment circuits of these plants. The objective is to identify the cause of some of the difficulties and propose possible solutions so that the next generation of lateritic operations can emerge as technically and, more importantly, economic successes. A number of these process improvements have been identified by the existing operators and in many instances have been or are being implemented into the existing operations.

Jan 1, 2004

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By J. G. Patterson

"The depressive action of sodium cyanide on chalcocite has been investigated and found to be unstable. Flotation results show that with the addition of sodium cyanide to the system chalcocite is initially depressed but rapidly recovers with time, provided there is sufficient oxygen present.lt is proposed that the unstable depression is due to the reaction of cyanide with adsorbed xanthate and copper ions at the chalcocite surface to form soluble copper complexes. When all the free cyanide has so reacted, xanthate anions can then re-adsorb on the chalcocite surface and the flotation will recover. Results are presented to verify the the above mechanism."

Jan 1, 1968

By F. Bélanger, P. A. Fournier

"Modelling and optimization techniques used in the operation of the Detour Lake Mine leach circuit are contrasted to a 1973 review of contemporary techniques used by a major gold producer. The leach circuit at the Detour Lake Mine was modelled using a full factorial Design of Experiment of stirred tank reactor leach tests using circuit feed. Contour plots of extraction were applied in the plant to optimize addition rates of cyanide and the newly-commissioned lead nitrate system. Contour plot sections were used to understand the impact of sulphur in circuit feed at different operating dissolved oxygen concentrations. The 1973 review paper offers insight into industrially-applied modelling and optimization techniques. In particular, a mathematical model of plant data was developed using multilinear stepwise regression analysis. The model was presented using graphical representations available at the time and applied to optimize the rates of cyanide addition. Off-the-shelf software solutions of today allow mineral processors to quickly and easily visualize data, allowing them to re-allocate time and resources spent processing data to generating raw data and extracting actionable information.IntroductionModelling and optimization in mineral processing is the art of reducing reality through judicious use of assumptions to understand a process and leverage this knowledge to engineer practical solutions to metallurgical problems. Data analysis is at the core of this enterprise.While this paper showcases the modelling work done at the Detour Lake Mine (DLM), the primary objective is to pause and reflect on how far the field has progressed since the 1970’s. A snapshot of state-of-the-art gold cyanidation modelling at that time is a review paper of the Anglo American Group’s capabilities (Brittan & van Vuuren, 1973). The objective of this paper is not a play-by-play of the evolution of modelling and optimization since that time. Rather, it is a comparison of the field at two points in time.In 2016, DLM undertook an extensive bench-scale leach circuit modelling program to better understand the impact of cyanide, dissolved oxygen, lead nitrate, grind size, density, and pH on gold cyanidation (Fournier, 2016). Two major capital expenditure projects were anticipated for 2017: improvements to oxygen control and a lead nitrate distribution system. While the lead nitrate system was planned for construction, the design parameters had not yet been selected. Following the development of the model, plant trials were executed to validate aspects of the model and the methodology was expanded to address other plant issues, in particular the effect of talc chlorite and pyrrhotite in leach feed.The variables of the bench-scale study are summarized in Table 1. Dependent variables were varied using a full factorial design of experiment with two repetitions for each test condition, yielding a total of 300 tests. Test order was randomized to eliminate bias from independent variables."

Jan 1, 2018

By Minghui Li

China is the largest coal producer in the world. In 2012, the coal production in China is 3.65billion tonnes, accounting for approximately 49% of global coal production. The raw coal production in 2012 was 3.8% more than the year 2011. 56% of total raw coal has been washed. The increase in raw coal production also promotes technology to be developed and brings separation capacity become larger and larger in coal processing in China. At present, over 40 extra-large scale coal preparation plants (each plant has capacity of more than 10 Mtpa) are in operation in China, the largest one is 32.5 Mtpa. Heavy medium separation are widely used in new built coal preparation, the washing limit for thermal coal feed lower and lower, the equipment selection tends larger which brings the whole washing system simplified, the local equipment developed and manufactured are more and more used. By discussing designs of several typical thermal coal preparation plants and coking coal preparation plants in China, this thesis introduces the current design of China?s extra-large coal preparation plants, and sums up the prevailing design features and trends of extra-large coal preparation plants.

Aug 1, 2013

By A. G. Pronk, D. M. Burton

"A regional till sampling program in the Upsalquitch Forks-Tetagouche Lakes area, centred some 70km west of the city of Bathurst, has proven an effective method for gold exploration in the heavily glaciated interior of northern New Brunswick. Prospecting activities within this area over the past three years, have led to the discovery of several gold occurences associated with quartz-carbonate alteration in a variety of intrusive rock types emplaced along major fault zonesQuaternary mapping shows that the glacial history is complex. However, the displacement of material is uniform in distance and direction, and the till is generally thin (0.5 m to 2.0 m) and locally derived, making the interpretation of till geochemical patterns relatively simple for the explorationist. Previous studies have shown the the fin e-grained gold is best detected in the -250 mesh (-0.063 mm) till fraction (clay plus silt) and that the C-horizon is the preferred medium for analyses.Samples were collected on a 2 km grid and analyzed f or Cu, Pb, Zn, Au, Ag, As, Sb, Mn, Fe, Ni, Co, and Cd. Results indicate that concentrations of 10 to 20 ppb Au can effectively delineate areas of anomalous gold in bedrock associated with fault structures, and that a good potential for discoveries exists to the west of the known occurrences, where up to 678 ppb A u has been detected in tills. IntroductionThis paper reports on the result s of surficial geological investigations conducted over the past two field seasons in north-central New Brunswick. The stud y area is located in the Upsalquitch Forks-Tetagouche Lakes map area s (N.T.S. 21 0 19 and 21 0 (10) 70 km west of the city of Bathurst (Fig. I). The area is situated on the margin of the New Brunswick Highlands and has a maximum elevation of 640 m (for a detailed description of the physiography, see Rampton et al. 1984).Historically, exploration in northern New Brunswick has concentrated on base metals within the Cambro-Ordovician Tetagouche Group, resulting in the discovery of man y significant massive sulphide deposits (Brunswick No.6 and No. 12, Heath Steele, Caribou, Armstrong Brook, Orvan Brook, McMaster, Murray Brook, and Restigouche). Auriferous base metal occurrences along the Rocky Brook-Millstream Fault have also been previously investigated."

Jan 1, 1988

By R M. Ennis, J. C. Botham

This paper is one of a series pre-pared to study the role of fuels and reductants in metallurgical processes, especially from the viewpoint of Canadian requirements. The object of these studies is to provide a reason-ably authoritative interpretation on the interrelation of fuels in light of the considerable changes that have taken place in the Canadian energy field during the past few years. Previous papers in this group have dealt with the problem generally, and specifically in terms of the development of the iron and steel industry of Western Canada. These latter papers, presented at the Symposium on Iron and Steel in Western Canada held in Edmonton, Alberta, on September 8-9, 1959, surveyed the ferrous processes of interest for use in Wes tern Canada, especially with regard to solid fuel requirements. At that time it was evident that there was a need for a similar study of the fuels aspect of the non-ferrous metals industry.

Jan 1, 1961

By M. Hozayen, Q. Ni, E. S. Radwan, P. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests used in this study are summarized in Part I of this paper whereas wellbore stability analysis and formulation of a3D geomechanical model that was built for that purpose is summarized herein.A 3D geomechanical reservoir model was developed, which included natural fractures. The mechanical properties of the reservoir rock, such as Young’s modulus, Poisson’s ratio, UCS, friction angle and tensile strength were populated based on the correlations established in Part I of this paper and the developed model was then used to simulate the 3D mechanical-property distribution and the evolution of the in situ stresses in the field due to depletion from 1983 to present-day. Based on the full field model, mud weight cubes were developed to predict the safe mud weight windows in different drilling directions. In addition, well stability prediction for two planned wells was performed using a 3D near-borehole model. Firstly, the computed stress state and mechanical properties simulated in the full field model were extracted along the well trajectory of an existing horizontal well which was drilled recently and then, a3D near-borehole model was constructed along the well trajectory. The wellbore stability analysis along the well trajectory, including stress state, strain distribution and displacements, was performed to identify the instability events along the well trajectory. It has been seen that the presence of natural fractures is closely related to the recorded borehole instability incidents. The computed plastic strains which indicate the wellbore failure were consistent with the recorded wellbore instability events in the FMI image logs, what provide further verification of the developed model. Then, this 3D near-borehole model was applied to two planned horizontal wells and the wellbore stability analysis for the two wells was carried out.The results showed that drilling vertically in the reservoir is safer than drilling horizontally. However, the drilling mud weight window in the vertical direction is narrow, being as narrow as 18.7 pcf or 0.299 sg locally. Drilling horizontally is less stable towards the maximum far field stress direction than towards the minimum far field stress direction. The mud weight cubes were used to identify the optimal well placement and well trajectory. For planned well trajectories, this technology can also be used to determine the optimal mud weight."

Jan 1, 2015

By Z. Pilecki

This work concerns the identification of weak zones in the structure of a rock mass endangered by outburst of gases and rocks in the Rudna copper ore mine at greater depths (approximately 1200 m). A special methodology has been undertaken for the recognition of that threat in the wake of an outburst in the mine in 2009. No similar phenomena have been previously recorded in KGHM Polska Miedz copper ore mines. The research described in this paper was carried out in the new part of the deposit prepared for mining. Geophysical methods were used: seismic tomography and borehole ground penetrating radar (BGPR), along with particular identifications using geological engineering methods. In the researched area, Permian layers of sandstone and shale clay (Weissliegendes formation) and of Zechstein dolomite (top of Rotliegend formation) and anhydrite occur in the copper ore deposit. The rock layers are characterized by variable thickness and intensity of mineralization, varying internal structure, and local fracturing containing different gases and water. It is assumed that accumulation of gases occurs in the tectonically fractured dolomite. The study was focused on the recognition of the structure and properties of the dolomite layer lying directly within the roof of excavations. The first tests were performed with seismic tomography for the recognition of anomalous changes in the elastic properties of the rock mass. The results of these studies were used to design a control borehole for a detailed geological engineering assessment and BGPR surveys with 100MHz antennas. Seismic tomography enabled the identification of changes in Pwave and S-wave velocity, the Vp/Vs ratio, dynamic Poisson's ratio and dynamic Young's modulus. It was clear that seismic anomalies required verification by other methods. The BGPR survey was performed in a specially designed borehole, passing through the selected seismic anomalies. While the borehole was being drilled, the outflow of gases was identified, with varying amounts of CH4, CO2, and H2S detected, as well as water outflow. The results of BGPR confirmed the location of a reservoir of water and gases, about 30 m in length, found in layer of dolomite. The direct cause of the BGPR anomaly was assumed to be intensive fracturing, a greater content of clay material in the dolomite, and the presence of water in the fractured zone. The BGPR image was correlated with information on lithology, fracturing based on the RQD index and additional information acquired during drilling about water and gases surveys and other symptoms. The achieved results also showed a very strong correlation between the location of the zone containing gases and water and the anomalous S-wave velocity and field of dynamic Poisson?s ratio, and to a lesser extent other seismic parameters. It was found that the other measured seismic anomalies may be of the same nature as those identified in the control borehole and accordingly will require the implementation of detailed identification. The performed tests have also shown the usefulness of geophysical methods to identify geodynamic hazards under the geological and mining conditions of the copper ore deposit in the Rudna mine.

Aug 1, 2013

By George H. Bodfish

This paper begins with a short history of air compressors, emphasizing their "roots" in the mining industry. It then describes the types of compressors available, including reciprocal, the various rotary positive-displacement compressors, and the centrifugal. The advantages and disadvantages of selecting a certain type of compressor over another are enumerated, considering customer requirements and operating costs, among other factors. Guidelines to operation and maintenance are discussed, including installation, monitoring and maintenance procedures. Finally, the paper addresses itself to future trends, with special attention being given to the system concept, the increasing use of rotary compressors, power consumption, reliability, packaging and noise attenuation.

Jan 1, 1978