Search Documents

By F. J. A. van Ruitenbeek, M. Dalm

In the presented study test work was performed with near-infrared hyperspectral imagery (NIR-HI) on 36 ore samples from a South-American epithermal Au-Ag mine. The aim of the test work was to investigate if NIR-HI provides information about the alteration mineralogy of samples that can be used to predict their economic value. Mineral distribution maps were produced from the hyperspectral images by using correlation coefficients between the image pixels and a set of reference spectra. These maps showed that detection of mineralogy with NIR-HI can be used to distinguish; i) ore particles with low Au and Ag grades, ii) ore particles with high carbon contents, iii) ore particles with high sulphur contents.

Jan 1, 2015

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By J. Janeson

Wall control at the Pipe Open Pit is of primary importance in ensuring the long-term stability of the operation, while keeping costs to a minimum. Blasting techniques have been adapted to the variations in competence and structure of the wall rocks. A portion of the perimeter wall is being developed in incompetent peridotite . A recent change in pit slope design provides a wide safety berm on alternate benches. A support program which consists of pinning the crests of wide berms with vertical reinforced concrete dowels and horizontal bolting of walls shows evidence of increasing the stability of the pit walls. This paper describes the blasting and support techniques which are contributing to successful wall control in the Pipe operation.

Jan 1, 1979

By Peter M. Watt

The objective s of this paper are: (a ) to examine and discuss the burdens we place on our extractive industry; (b) to compare the levels of taxation in Canada with those in other countries; and ( c) to suggest certain broad parameters within which our taxation policies may be made more rational and stable. Among the burdens identified are taxation, the ownership and use of our resources, environmental issues and the rather emotional issue of so-called 'super profits'. Finally, the paper will address certain broad but key areas of policy which need attention and agreement if our tax system is to be made more rational. Such areas include: whether and if so why the extractive industry should be given incentives;. what circumstances, if any, justify a 'higher' than normal' level of taxation, and, ?if the concept of economic rents is a justifiable one, how might a basis for them be established which recognizes the fluctuating value of much of the industry's output. Note: The paper was written before the 1977 Federal and Provincial budgets were presented. Consequently, the paper does not reflect any changes proposed in these budgets.

Jan 1, 1977

By A. L. Mular

"This paper summarizes the present-day usage of computers in the mining-metallurgical industry. The industry appears to be following a path taken by other industries in improving the operation of processing plants, production schedules, grade control and haulage performance. A reduction in the cost of computers and computing has been a significant factor.An attempt is made to forecast the future of computers in our industry. Such developments as time-sharing, mini-computers, and easy-to-understand process-oriented languages will lead to wider usage. Considerable strides have been made in the use of computers for laboratory data acquisition. In general, the implementation of new methods, new techniques and new equipment will require plant personnel to develop new skills. The universities are meeting this challenge by re-structuring curricula and offering special courses. Most vendors of computers already offer special courses within their own facilities at a customer's plant."

Jan 1, 1970

By W. R. Cowan

The Caledon Outwash is a large deposit of glaciofluvial gravel and sand located 55 km north west of down town Toronto. For the most part it was laid down in a meltwater channel fronting the Paris Moraine about 14,000 years ago. Applying the braided bar model of Eynon and Walker (1974) the principal facies present are imbricated coarse gravels (bar corefacies); crudely stratified, imbricated bar top sandy gravels; and trough crossbedded side channel sands and gravelly sands. Of lesser importance are crossbedded bar front gravels, shallow braided stream facies gravels, and stoss side facies sands and pebbly sands (rare). Lithologically these deposits are characterized by FIGURE I. Geological relationships of Caledon Outwash. Industrial Minerals in Canada up to 95% Ordovician limestone and siltstone in the gravel fraction. A siltstone content of up to 34% requires that beneficiation be carried out for the production of better quality aggregates. Resources remaining are estimated to exceed 500 million tonnes in 3000 ha of the most suitable part of the deposit. Present production is about 4.5 million tonnes per year, shared by several producers.

Jan 1, 1984

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By P .. H. Grimley, N. Champigny

"Fourteen companies (Appendix) representing senior mining organizations in Canada were canvassed in order to assess: (1) the current usage and trends, and (2) the usefulness of computer applications in ore reserve estimation and grade control. The results of the questionnaire suggest that:• computers are unsurprisingly, predominant in the mining industry for calculating reserves and performing grade control;• time and cost savings are realized;• computer-based approaches are applicable to underground situations;• geological information is incorporated to the computerization process; and• computer usage does not hinder the collaboration of geologist and mining engineer.A clear need is identified for case histories comparing computer-calculated ore reserves and actual production data.IntroductionAmong the management and technical staff of some mining companies there is a perception that the application of computer based technology for the estimation of ore reserves and grade control, has as many drawbacks as benefits. Some of the objections raised against the utilization of computers for ore reserve estimation are that:• computer-based reserve models work for large open pit mines but not for underground situations;• computer-generated reserves ignore the geologist's knowledge base; they are strictly a number crunching exercise; and• the use of computers for ore reserves hinders collaboration between the geologist and mining engineer.In order to determine (I) the extent of current computer usage and future trends and (2) whether the objections noted above are borne out by experience, a number of senior Canadian mining companies were canvassed.The respondents were asked to provide:• an assessment of the importance of the computer in the ore reserve estimation and grade control process;• the level of involvement of individuals and staff groups with computer-based ore reserve estimation;• the advantages perceived and realized from the utilization of computer-based ore reserve approaches;• the current and future human resources requirements for the evaluation, implementation, maintenance and development of computer-based ore reserve systems;• the hardware and software resources presently used and planned; and• the developments needed to increase the use and acceptance of computer-based ore reserves."

Jan 1, 1990

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By T. T. Ni

FOR MORE THAN 200 years, the Kochiu district of Yunnan province has been, and it still is, the hub of China's tin industry. The district produces annually from 80 to 90 per cent of that country's out-put of tin, which averages about 9,300 tons a year and places China fifth among the tin producing nations of the world. The tin ore reserves of the country are estimated (1) at 1,873,370 metric tons, of which 1,500,000 tons are in the Kochiu district. The mill of the Yunnan Consolidated Tin Corporation, described in this paper, is the only one of its kind in China. MINING AND SMELTING There are only two tin mines in the Kochiu district operating with modern equipment -the Hsin-Chang and the Lao-Chang, both owned by the Yunnan Consolidated Tin Corporation, a government company. The Hsin-Chang mine has four working levels with cross-cuts 6 ft. by 6 ft. and is equipped with steel mine cars and trucks to haul the ore. The ore is hoisted to surface in a three-compartment shaft and transferred to the mill by a 4-kilometer aerial tram. The Lao-Chang mine has two circular shafts 656 feet apart, each equipped with two cages. Haulage-ways 1,600 meters and 1,000 meters long, respectively, have been driven to the southwest from these shafts and are connected by three cross-cuts.

Jan 1, 1951

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

By G G. Suffel

T HESE remarks on the occurrence of strata-bound massive sulphide deposits are submitted be-cause the writer recently visited the principal Cyprus deposits (in January, 1965) and has also a back-ground of many years spent largely in detailed observation and map-ping of the Horne and Amulet ore-bodies, now largely inaccessible. They are particularly related to the Symposium papers (September Bulletin) by Hutchinson and by Roscoe. Some comments are offered on the cupriferous pyrite deposits of Cyprus. As the writer is currently reviewing the published literature on the related deposits in Turkey, a brief account of some characteristic Anatolian sulphide occurrences is given. The discussion is closed with some thoughts on the relationship between these Mediterranean sulphide deposits and those of northwestern Quebec and the Superior province in general. The geology of Cyprus, as it relates to the sulphide deposits, is well summarized by Hutchinson (1965). After visiting Mavrovouni, Skouriotissa and Limni and after much thought on the possible ge-nesis of these ores, it seems quite logical to me that he is right. They are indeed closely related to late-stage submarine volcanism.

Jan 1, 1965

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By L. Xia, B. Hart, G. Gingras, M. Furlotte

Plant and laboratory test work was performed in order to optimize a copper/zinc flotation separation circuit at Matagami concentrator, Canada. The testing identified a significant difference between the laboratory testing and the plant flotation, particularly for the sphalerite recovery in the rougher copper concentrate. Tests indicate that sphalerite recovery of the flotation concentrate in the laboratory testing was significantly higher than in the plant. The ToF-SIMS surface analysis identifies surface species responsible for the discrepancy in Zn recovery. It shows that sphalerite flotation is in response to the collector attachment and a significant enrichment of Cu on the surface of sphalerite grains. A comparative surface chemical analysis was performed on both sphalerite and chalcopyrite grains from the plant flotation and laboratory testing in order to identify surface species variability between the two testing. Two significant observations were revealed. First, there is considerably more hydrophilic iron oxyhydroxide on sphalerite surface from the plant flotation sample relative to those from the lab testing. The secondary coating likely completely or partially passivates sphalerite surfaces, reducing Cu enrichment and hence sphalerite floatability. Secondly, comparing the surface chemistry on sphalerite and chalcopyrite, the hydrophilic iron oxyhydroxide species have preference for the sphalerite grains relative to chalcopyrite. Despite numerous studies on the effect of galvanic coupling during grinding, there is limited documented evidence on the effect of the milling environment on the flotation and plant operations. This observation suggests that interaction between sulphide minerals and grinding media have a significant influence on subsequent flotation. This paper discusses the results of a detailed surface chemical evaluation of sphalerite grains from both the plant and laboratory testing in the context of grinding environments and pulp chemistry.

Jan 1, 2016

By J. Visman

"Cyclone separators of different design are being used in increasing numbers in the coal industry of today. One recent addition, the Compound Water Cyclone, is finding application in the North American and Australian coal fields for the beneficiation of coking coals and for the reduction of sulphur and ash in steam coals. In this paper, the combination of specific-gravity separation, thickening, classification and water recovery are discussed. All of these operations can now be accomplished by means of cyclones that are effectively combined in circuits of compact design. In the layout of such integrated plants, three main sections are distinguished, namely: a Main Section for cleaning the plus-28-mesh fractions; an Effluent-Beneficiation Section for treating the minus-28-mesh fractions; and a Water-Recovery Section, where the wash water is reconditioned, and the fine solids are removed in a semi-solid state as slugs or pellets. Depending on the nature of the coal and the specifications of the purchaser, water-cyclone circuits can be flexibly combined with HM Cyclones and froth flotation, as well as with ancillary equipment for dewatering and drying."

Jan 1, 1968

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

By Hatch, A. Reple, W Valery

The mining industry is facing declining feed grades which require the mining and processing of larger volumes of material per tonne of product. Pre-concentration aims to remove barren material at as coarse a particle size and as early in the process as possible to reduce processing costs, energy consumption, water losses, and greenhouse gas emissions while increasing production and profitability. This may be achieved using bulk ore sorting—the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor. This paper evaluates the technical and economic viability of bulk ore sorting for the PanAust Phu Kham copper deposit in Lao PDR. Bulk ore sorting technology is described briefly along with discussion of appropriate sensor and diversion systems for the Phu Kham operation. To evaluate the economic implications, the actual mined material and costs from 2014 were used as the base-case. Sampling data was not available; therefore, the ore grade variability that would feed a bulk ore sorter was estimated using geo-statistical tools based on mine grade control data. The sorter performance when treating this material was simulated considering the accuracy of the sensor measurement and errors associated with material diversion. The impact on inferred cash flow was estimated for several different scenarios considering the additional costs for sorter operation and reject handling. The evaluation demonstrated that bulk ore sorting at Phu Kham has the potential to increase the amount of metal in product and/or reduce processing plant throughput (and costs) to improve the annual inferred cash flow for the conditions investigated. The sorter is the gatekeeper – only material above the cut-off grade (value-adding) reports to the processing plant; no waste dilutes the feed. Likewise, above cutoff grade material is not lost to waste; preventing lost revenue.

Jan 1, 2016

By M. E. Hurst

Introduction Between 1903 and 1905, W. Mclnnis, of the Geological Survey of Canada, made a micrometer traverse of the Kawinogans (Crow) river from Kapkichegimaga lake to its junction with the Otoskwin river. He reported that a belt of Keewatin rocks, 1 to 4 miles wide, was exposed along the course of the river for 17 miles east of Kapkichegimaga lake. Prospectors and exploration companies paid little attention to the mineral possibilities of this belt until the summer of 1928 when, with the adoption of airplane transportation, the area became readily accessible. Within a short time widespread interest was aroused by the announcement of attractive finds, and a mild rush followed. During the winter months, hundreds of claims were staked on either side of Crow river for 12 miles east of Pickle lake. In the summer of 1929, much of this ground was systematically explored and a considerable amount of development work was done on the known deposits.

Jan 1, 1930

By Melvin S. Taylor

The environmental control program at Cassiar Mine is an active one involving government, unions and company personnel all working together to achieve a goal- "A clean and safe working environment". This can only be achieved by utilizing three of Cassiar's most important resources; i.e., people, time and money. Past environmental programs have more than proved that the goal can be reached and. with the future programs now in progress. Cassiar Asbestos will achieve its environmental goals.

Jan 1, 1978