Search Documents

By Singh RN, Yuejin LI

The problems experienced with longwall mining machinery motivate the development of an expert system for fault diagnosis. The techniques of knowledge representation, database, knowledge base and inference engine guide the selection of the expert systems and languages -"Turbo Prolog"- as exemplified in the case study of hydraulic support. The aim is to hasten future development of a fault diagnosis system and the design of a system to locate and determine the causes of failure of longwall machinery. The system would use its stored case history and other information to make fault diagnoses and suggest appropriate remedies. Consequently down-time would be reduced and production and profitability should increase.

Jan 1, 1991

Whether you are an employee, contractor or consultant working in the mineral industry, there are pressures to deliver the best possible performance. Technical professionals are usually driven by an internal desire to perform to a high standard because of personal pride in their profession, but there are an increasing number of external requirements to demonstrate that the actions taken were based upon reasonable grounds and that the work conformed to current best practice. People expect these best practice procedures to be followed and governments are now requiring those tendering for contracts to be registered in some way and to be participants in quality assurance schemes. One is not immune to these pressures just because you are working in a less legislatively sophisticated developing country in the circum-Pacific rim (Pacrim) region.

Jan 1, 1995

Mineral sands make up only 3% of the value of mineral production in WA. However, the distribution of mining operations, close to the more highly populated south-west coastal areas, and the wide range of land-tenures and land-uses involved has resulted in the most complex range of regulatory procedures found anywhere in the State's mining industry.Mineral sands are mined on private agricultural and "minerals-to-owner" land, State forests, nature reserves, coastal reserves and vacant Crown land. Local Government authorities, State Government departments and private landholders can, depending on the land tenure, be involved in setting the environmental conditions for mining operations and supervising subsequent rehabilitation. In the past, rehabilitation was predominantly aimed at establishing an agricultural land-use after mining; however, it is now necessary for mining companies to rehabilitate mined areas to a much wider range of end land-uses.

Jan 1, 1986

By Enichlmayr E

Lignin grouts are cheap and easy to get. They have some desirable properties, but they aag less used now because environmental pollution is often caused by Cr from the lignochrome component of the grout. Their usefulness was researched in an earlier paper on lignin as a grout from other viewpoints. A non-toxic grout FUL was made composed of furfural, urea and lignin. After initial tests, including tests by spinning regression design, some response equations in which FUL's properties are described were obtained. Optimum formulations have been established by using optimization methods based on response equations. The engineering quality was assured by formulations whose properties were measured in further tests. The mechanical feature of gelling sand was measured by means of triaxial tests. This provides a basis for using FUL grout in-situ. Finally, an in-situ experiment on FUL was completed successfully. The results were that cracks in stratum were filled or blocked, the gelling of FUL had high strength, and low permeability and consolidation were achieved.

Jan 1, 1988

By Gochin RJ

This paper focuses on measures of the economic significance of mineral exploitation and processing activities, such as beneficiation, refining and smelting. Empirical measures are suggested to quantify the relevance of the degree processing within a nation's mineral industry. The most useful, based on the input-output econometric framework, are used to establish the magnitude of links between the mineral industry and its satellite activities and for the appraisal of large, non-marginal projects. The input-output impact analysis is refined to allow for country specific behaviour and synthetic indices for the appraisal of investments in the mineral sector are developed. These indices are further improved with the introduction of shadow prices to incorporate socio-economic issues. They are useful to direct mineral policy decisions and several investments towards the most promising objectives for national goals. Finally traditional methods for the appraisal of small scale, marginal, mineral projects are assessed where local impact and regional development issues are more relevant than national ones.

Jan 1, 1993

During the 1998/99 Asian crisis Solid Energy's export revenues collapsed from over US$70M to under US$40M. Simultaneously, domestic market uncertainty led to decreases in volumes and prices. A major new underground mine was not technically viable, and was closed, and several other mines were marginal. Less than two years later, Solid Energy and its JV partner closed a second new underground mine. The company was in financial crisis, and reported an $86M loss for 1998/99. After refinancing with stringent workout conditions it still had minimal returns due to low prices, unaffordable transportation costs and huge unrealised FX losses as the NZ dollar fell 40 per cent in value. The obvious scenario was to æcash upÆ û complete extraction at remaining mines, sell off any viable parts of the business, pay off debt and wind the company down.In 2002 Solid Energy has completed its recovery. Although margins remain slim and volatile in both export and domestic markets, it is achieving record volumes and revenues. It has paid off its shareholder loan, has minimal remaining FX losses, and cashflow is allowing further mine and infrastructure development. The key to the turnaround has been implementation of rigorous planning, analysis and decision-making in all aspects of the business. The company has a comprehensive, rolling 20-year plan used annually to update rolling five year and annual business plans. Solid Energy augments strong line management operations with rigorous standards and processes for mine planning and development, operational decision-making, and functional support. Detailed, quantitative risk analysis is used in all aspects of the business and allows comprehensive integration of opportunity and risk management across all activities in the company.Coal mining is widely perceived as an æold-economyÆ industry. But, like other successful æold economyÆ companies, the information systems and management processes used by Solid Energy are as leading edge as any in the high-tech sector. They are the key to managing to add and sustain maximum value for a company that has access to coal resources sufficient for hundreds of years.

Jan 1, 2002

Petroleum exploration and development is vitally important for the future well being of Australia. The Australian petroleum exploration/development industry is alive but not so well. A combination of.:factors point to the industry requiring a much more mature effort in both short and longer-term planning to ensure greater success and effectiveness for petroleum discoveries and development. While many petroleum exploration companies are competently run, there are far too many which will be lucky to survive, even though their exploration areas are highly Prospective.

Jan 1, 1983

This paper presents a review of heat illness in mining, including reference to several recent investigations by the author. Heat illness is a collective term, covering the conditions of heat stroke, heat exhaustion, heat cramps and miliaria rubra. Heat stroke is life-threatening and is by far the most serious condition. It is rare in mining, if appropriate control measures are instituted. Heat exhaustion is primarily due to hypohydration, following prolonged sweating in hot conditions. Symptoms include fatigue, headaches, dizziness, anorexia, nausea, vomiting, shortness of breath, or brief syncope. Confusion, ataxia, prolonged unconsciousness or convulsions are strongly suggestive of heat stroke. Heat cramps are painful involuntary contractions of skeletal muscle associated with work in hot conditions. The limbs are usually involved and the spasms typically last a few minutes, during which the affected part of the body is incapacitated. Heat cramps tend to occur in heat exhaustion, when hypohydration becomes marked. Miliaria rubra is a skin rash caused by extravasation of sweat into the skin, as a result of obstruction of the sweat glands. It occurs after prolonged and profuse sweating in hot environments. It can take three to four weeks of sedentary duties, in an air-conditioned surface environment, for the condition to resolve. Heat illness would be unlikely in underground mining, if the thermal environment was sufficiently well controlled by ventilation and refrigeration. This is however, often not practicable. Where engineering controls alone cannot provide sufficient control of risk, the residual risk can be assessed using an appropriate heat stress index. While procedural controls may further reduce the residual risk, it is important to remember that these are less reliable than engineering controls and cases of heat illness may still occur. Procedural controls include the application of heat stress limits, education, hydration, self-pacing, early symptom reporting, medical advice, acclimatisation procedures, air conditioned accommodation, support to achieve a healthy body mass index, and an effective emergency response capacity.

Jan 1, 2005

Detailed studies of mineral paragenesis, isotope and trace-element geochemistry, and physical mineralogy at Mount Morgan are compatible with deductions by Geopeko Ltd geologists concerning field relationships in the mine area. Considered together, field and laboratory data suggest that the Mount Morgan deposit originated from a shallow, intrusive, acid volcanic dome similar to those which produced the Kuroko-type deposits in Japan. At Mount Morgan, however, interaction with sea water was much less, the sulphides were concentrated rather than forming a group of deposits, and only the throat of a breccia vent is pre- served, so that only the lowermost parts of Kuroko-type deposits can be compared with the Mount Morgan mine. A final difference lies in the presence at Mount Morgan of a quartz diorite adjacent to the ore. Mineralogical data are compatible with post-ore intrusion, possibly up an earlier volcanic fissure.

Jan 1, 1974

By S Blackburn, T Veasey

The physical and mechanical properties of rock can be measured by a variety of standard tests, and studies have shown that there should be a fundamental connection between breakage in comminution and rock æstrengthÆ. The current study aims to develop the ring-loaded strength test, used as an industry standard for the characterisation of brittle ceramics, for determination of comminution behaviour from exploration borehole core samples. The test procedure is simple, reproducible and can yield 250 separate measurements from a one metre length of drill core. The effects of material grain size and fabric on the degree of scatter of results have been investigated with respect to the ring-loaded strength test. This study has also compared the ring loaded strength to the chevron bend test used to determine the Mode I fracture toughness. A wide range of rock materials have been studied and with further work it is conceivable that an operational work index could be obtained directly from exploration drill cores tested via the ring-loaded disc test.

Jan 1, 2000

By Beattie T

For many years explosive sensitized explosives were assessed using the ballistic mortar. The standard test used lOg of explo- sive initiated with a detonator. Over the past 30 years many non- explosive sensitized explosives and blasting agents have been developed. Most of these new explosives and blasting agents cannot be tested in the ballistic mortar as they are not initiated by a detonator. It is also known that all explosives have a criti- cal diameter. When the cartridge diameter is less than the criti- cal diameter a stable detonation cannot be produced and the explosive fails to propagate. For many blasting agents the criti- cal diameters are greater than 50mm and such large diameters cannot be tested in the ballistic mortar. The underwater test allows explosives to be tested in diameters greater than the critical diameter and to be adequately initiated with suitable boosters. The effects of the explosive on the water are easy to measure and the test provides a safe, convenient and reproducible means of assessing explosive performance. The reaction products are allowed to expand to a low final pressure. The underwater test can therefore be used to give a measure of the total expansion work of explosives. The detonation of an explosive induces a shock wave in the surrounding water. The profile of the shock wave can be meas- ured 3-6m from the charge and the energy in the shock wave cal- culated. Measurements over a range of distances show that the shock wave is attenuated as it travels through the water and the attenuation is different for each explosive. This makes it difficult to estimate the energy dissipated in the water between the charge and a single gauge. The reaction products continue to expand and displace water. The bubble continues to expand until the kinetic energy of the water is zero. The gas pressure in the bubble is now lower than the hydrostatic pressure and the bubble radius is a maximum. The higher external hyrdostatic pressure causes the bubble to implode. The bubble energy is the work done displacing the maxi- mum bubble volume against the hydrostatic pressure and can befound from the bubble period. It is not always easy to find a large enough pond for the bubble to expand undisturbed by the water surface and the containing boundaries. This makes it difficult to determine the bubble energy accurately in shallow Ponds.

Jan 1, 1988

Secondary steelmaking (or ladle metallurgy) has been developed as a post- steelmaking ladle treatment to produce steel of superior quality. Its rapid growth has resulted from quality improvements, productivity increase, operational flexibility and process route economics. Advances in secondary steelmaking are very impressive during the past decade, and many commercial systems have been developed for performing one or more of the following unit operations: degassing, atmosphere regulation, reheating, refining with synthetic slag, rinsing gas treatment, injection of solid materials and alloying. The metallurgical requirements imposed by the current competitive steel market include more precise analysis tolerances, minimum level of detrimental elements, improved cleanness, demanding service performance and better processability. In most cases, these requirements could only be realized by the application of appropriate secondary refining facilities. Continuing developments in simplicity of design, cost advantage, quick cycle time, improvements in peripheral services such as refractories, instrumentation and in-situ analysis, extensive exploration of new applications, and the use of computer, can be expected. An exciting future is predicted for the widespread adoption of secondary steelmaking to perform most of the major refining functions over a variety of steel quality. It will also become a vital link in the total steelmaking process for production of tonnage steel at the large integrated steelworks and the mini-steelmills.

Jan 1, 1986

This paper deals with the Australian taxation laws, and in particular the income tax laws, as they apply to mineral exploration and development both in Australia and off-shore. The Australian tax laws are imposed principally at a Commonwealth level. The most important Commonwealth taxes are Income Tax, including Capital Gains Tax, Fringe Benefits Tax, Sales Tax, Customs Duty, Excise Duty and Bank Accounts Debits Tax. The States of Australia impose Stamp Duties and Financial Duties, Payroll Tax and Land Tax. The Australian Income Tax Law including Capital Gains Tax, is the most significant tax in the country. The principal features of the income tax law are as follows: tax is imposed on a taxable income being the assessable income less allowable deductions; a full imputation system of company tax applies; a foreign tax credit system applies to both companies and individuals; capital gains are taxed as income and subject to income tax rates but the gain is inflation adjusted. Australia has negotiated tax treaties with most of its trading partners based on the OECD model; and special tax concessions apply to the mining industry.

Jan 1, 1987

It is commonly accepted that govern ments have a role in the financing of mineral development. The reasons for government involve- ment are examined in general and in the light of the current situation in Aust- ralia, particularly having regard to the ownership of resources. A brief introduction is given to the new Australian Government bodies, the Petroleum and Minerals Authority and the Australian Industry Development Cor- poration, designed to fill a new role in mineral development, and to the basic changes brought about by the Australian Government's decision to become involved in the future development of the country's mineral resources. It is generally accepted that governments do have a role in financing mineral development. This acceptance does not seem to be confined to Aust- ralia alone but is more a worldwide phenomenon. Mineral development has traditionally been regarded as the pre- serve of private enterprise and there- fore is presumed-to be profitable, and so it is instructive to ask why there is this special role for governments.

Jan 1, 1974

By E Ahern

In exchange for issuing minerals rights from the Crown Mineral Estate to explorers and miners, the Crown expects a æfair returnÆ on this investment, ultimately for the benefit of all New Zealanders. In the case of mining permits, this return is in the form of a tangible asset û royalties from mining activities. But for exploration activity, the return sought by the Crown is an intangible asset û information. The information obtained serves three purposes û in helping Crown Minerals to set work programme conditions during permit allocation, for monitoring the performance of permit holders in accordance with permit conditions, and for archiving and making available for future interested explorers and other parties. Difficulties can arise during the allocation and monitoring process when either party has more information than the other that is not shared. To date not enough emphasis has been placed on the intrinsic value and content of the information generated by explorers and the importance this information can have in the exploration process leading to new mineral discoveries. For attracting exploration investment, the quality and availability of such information, combined with other geoscientific data, is a fundamental determinant for potential explorers when choosing to explore in a global market, and strongly defines the mineral prospectivity for a country. This is something the Australian States and other jurisdictions seeking mineral investment learnt long ago, and who now provide substantial amounts of cheaply or freely available packaged geoscientific datasets, increasingly over the Internet. To have a vibrant mineral exploration industry so that the benefits from the mineral estate can be realised for all New Zealanders, a shift in emphasis to the value of its mineral information base itself is required. Such an approach is befitting of a true Knowledge Economy, and would enable the Crown to make better-informed decisions regarding utilisation of its natural resources.

Jan 1, 2002

Many of the discrepancies that appear when comparing the results of reducing machinery are due to the nature of the materials reduced and the conditions under which they have been treated. It is therefore necessary that manufacturers should employ standard materials in their tests that sufficiently approximate the substances to be ultimately treated if the information is to be of any value to the purchaser. Another advantage to be gained by employing universal standard materials is that by their means one is enabled to compare the relative values of different types of machines. At present much of the data meted out to the public is insufficient to enable them to judge fairly. Of course the best test would be to send some of the stone tor which the machine is required, to be treated by the various crushers in the market that are likely to be suitable for the purpose, but this is not always possible. It would not take long to become accustomed to judge of the value of a machine for a specific purpose if it was guaranteed to work a certain quantity of some standard rock, even if that standard were not identical with the material to be treated.There are many points to be considered before selecting a machine, such as the size of the rough stone it will take, the size to which it will reduce it the proportions of various grades made when crushing to pass through a given mesh the form of the delivered particles the time taken to treat a+ certain quantity the horse-power required to drive the machine, both when loaded and unloaded whether constructed to crush wet or dry the wear and tear of the machine its total weight and weight of the heaviest part the cost of machine what attention it required whether the wearing parts are readily replaced, and several other points common to all machinery. 'When considering these varying quantities, we can tell at a glance certain machines that are suitable for a particular sort of work, and can then compare those belonging to the same class, thus avoiding errors made purposely or through ignotance by persons interested in different machines, who frequently compare machines originally constructed for.

Coal mining safety and health legislation is more than typical of safety legislation which has been born of adversity. Indeed, in the main it has been the child of disaster. Requirements which now appear obvious were indeed only occasioned by either social injustice or more commonly by great disasters. Even then changes were often made only after months or years of deliberation by committees. Early mining legislation in New South Wales benefited from the experience in Great Britain. The pioneers of our industry were miners from there and brought with them the basic British legislation, so we started with knowledge gained the hard way. A review of accidents statistics provides a measure of the effectiveness of mine safety legislation, but unfortunately rules cannot control human nature. Miners, managers and inspectors must work as a team to make mines safe and new legislation in New South Wales is planned to this end.

Jan 1, 1975

By Kelly BJ, Smith GA

The recommendations of a recent American report on "Better contracting for Underground Construction" are considered in relation to Contracting practices on major Australian projects by representatives Of the "classical trilogy" - the Owner, Engineer and Contractor.

Jan 1, 1976

The use of econometric models to assess the effects of a Government's policy on an industry is gaining momentum. This is particularly so for the Mineral Industry and it is important that mineral industry management understands the techniques involved in developing econometric models. Models are usually constructed outside the industry by either government departments or their consultants and used by the policy makers to investigate artificially the implementation and ramifications of new policies. This paper discusses the application of econometric models in Governmental policy determination, highlights the use of various models in Australia and gives an overview of the techniques involved using Australian examples.

Jan 1, 1982

By Tonkin D. A

Poor performance in the several stages of the magnetite recovery circuit, coupled with poor desliming through inefficient and over- loaded desliming screens, led to excessive magnetite consumption. An accurate and reliable sampling programme was established covering all outlets of the plant. Emphasis was placed on frequency of increments in an endeavour to detect extreme conditions of short duration. Systematic checking of the entry points to these outlets than identified those sections of the recovery circuit at fault, namely magnetite recovery separators and the heavy media cyclone product rinsing screens. More product rinsing water was provided, and modifications to the rinsing screens improved the efficiency of these units. Consistency of operation through automatic control of level eliminated the sudden massive losses in the magnetic separators. Load on the recovery circuit was then reduced by improvements to the raw coal desliming screens. A 50 per cent reduction in magnetite consumption was achieved.

Jan 1, 1974