Search Documents

By Will D. P

A 328 m, 2.4 m diameter raise-bored shaft has been equipped with a modular ladderway system to provide a second means of egress from Aberfoyle's Hellyer Mine in Tasmania. The modular ladderway consists of platforms, ladders and service pipes assembled at the surface and progressively lowered down the shaft. This system provides a rapid, safe and economical non-entry approach to equipping a shaft. The modular construction and single suspension allows for future extension or for reuse in another shaft.

Jan 1, 1988

Teller Underground Mine was established to extract ore from the Middle Vale Reef located on the eastern flank of Telfer Main Dome.The mine is located below a 150 m deep open pit operation. The ore body is shallow dipping highly structured, and is a main aquifer in quite difficult ground conditions.In respect of these conditions it was determined to access the orebody using an adaptation of coal mining and hard rock mining methods, with support being achieved using a combination of island pillars, rock bolts and timber stalls.The paper will describe these methods in more detail, then discuss the successes and failures of these methods when put into practice. As well, it will detail several factors whose influences were found to be greater than previously expected and stress the importance of good geotechnical advice.

Jan 1, 1993

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

By Terlich R. E, Finlayson J. M

A combination of high virgin rock temperatures, deep workings and extensive utilisation of heavy diesel equipment has presented North Mine (A Division of North Broken Hill Limited) with challenging ventilation problems. These problems have been addressed in a variety of ways which include in the order of 6000 kM of underground refrigeration. The future of North Mine depends on the successful development and extraction of ore in excess of 1100 m below the shaft collar using mechanised cut and fill mining. The success of this will depend on the installation of a complex chilled water reticulation circuit in this area. This will involve planning and constriction of a number of large dams, installation of pups and turbines, and the successful commissioning of several large water to air heat exchangers.

Jan 1, 1988

The specification for tender nominated the requirements for ore hoisting and servicing; this showed that one common duty winder could be selected. Foliowing the design of the shaft layout, the merits of fixed or rope guides were compared and the latter selected.The specification called for the supply and installation of the complete hoisting system. Construction of the winder tower and shaft bottom steel work had to proceed while mine development was in progress using the sinking winder and headframe. Guide ropes, winder ropes, and the sky shaft were installed in the shortest possible time, and as the shaft was not equipped with ladder-ways, a second means of access had to be provided.Very few problems were encountered witll the commissioning of the winder, and in the first 2 years of operation the only significant modification was to the circuitry associated witll the moving access platforms.Hoist rope tension checking and adjustment are simple, and non-destructive testing has shown no deterioration of these ropes. The operation of the balance ropes has been very satisfactory but cleaning presented problems in the early stages. Guide ropes have been trouble free and require minimum attention.Normal wear on the PVC rope groove inserts on the winder drum has been negligible.Since the commissioning on fully automatic ·control, the winder has operated with very few, minor delays.

Jan 1, 1969

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

Environmental impact and rehabilitation on completion are primary considerations in obtaining approval for mine projects from government authorities.This paper focuses on the planning and commencement of rehabilitation during the mining of an open cut mine (Hedges Gold Mine) in an environmentally sensitive area in the southwest of Western Australia.

Jan 1, 1992

By Skinner J, Brackenbury K

The AuPlus" Systems have been applied in the gold mining industry to achieve improved gold recoveries, faster leach kinetics and reduced cyanide consumptions. Calcium or hydrogen peroxide, collectively known as peroxygens, can be used. The choice depending on plant design and the nature of the ore. Laboratory test work and plant trials are included in this paper to illustrate the benefits of peroxygen usage in extractive gold metal- lurgy.

Jan 1, 1991

With the continued drop in export coal prices (as measured in US$) delivered to the Pacific Rim market, and a fixed annual 12 per cent increase in overburden, Usibelli Coal Mine Inc was faced with the need to reduce mining costs substantially or else forfeit its foreign coal contractual commitment which amounted to about half of annual mine output. Management made a difficult and fortuitous decision to proceed with an engineered plan to switch from a two seam, extended bench dragline operation to a two seam, cast blast and spoil side operation. While down-sizing and cut-backs became the rule in all departments of the mine, the drilling and blasting budget was more than doubled. Most will agree that this is contrary to what usually happens when a mine is faced with down sizing. The more common scenario would have management target the drilling and blasting budget for decrease as a first priority to cutting cost, and then later witness a decrease in equipment performance leading to an increase in the production cost per tonne. Although Usibelli Coal Mine more than doubled its annual drilling an blasting budget three years ago, the overall stripping cost has be, reduced by more then 37 per cent.

Jan 1, 1995

By Luke K. A

Pressure on production at New Zealand China Clays has led to the development of a dewatering control loop for fine halloysite china clay. The development was based on the analysis of data from the automation of plate and frame filter presses. The analysis of the data has led to process changes, and the ability to quickly solve dewatering problems. As a result of control in the dewatering circuit press times have reduced on average 117% and output has increased proportionally.

Jan 1, 1989

Carbonation of reinforced concrete is a potential durability issue for vehicular tunnels. This is particularly the case where elevated carbon dioxide concentrations exist and when the design life is 100 years or more. The process of carbonation can result in loss of passive protection to embedded steel reinforcement and initiation of corrosion. Therefore, tunnel design needs to consider the potential for carbonation on internal surfaces and how design life can be achieved in severe environments. This paper examines methods for predicting carbonation and how deterioration can be mitigated through appropriate concrete mix design and construction practices.

Jan 1, 2008

By Viney K. G, Molinia A. B

The Hellyer Pb-Zn-Ag orebody in western Tasmania was discovered in 1983, and mine production at a rate of 250 000 tonnes/yr commenced in 1987. Expansion to 1 million/yr will be completed by early 1989. Exploratory development to gain access to the orebody, to provide a 20 000 tonne bulk sample for pilot plant work and to confirm mining conditions and orebody continuity was undertaken using conventional drill and blast techniques and large diesel trackless equipment. A ventilation shaft was raisebored. Development in this phase totalled 2 815 m and provided a sound basis for rapid expansion of the mine.

Jan 1, 1988

By M Roper, M Lovitt

WMC Resources Olympic Dam Operation located in South Australia, is a poly metallic underground sublevel open stoping (SLOS) mining operation with a current annual production rate in excess of 9.0 Mt. Stope size, geometries, geotechnical considerations, drilling and blasting are critical components in stope performance. These factors are further influenced by stringent ventilation requirements due to the presence of airborne radioactive contaminants from uranium mineralisation. Stope planning is complex and mass blasting methodologies have been trialled at Olympic Dam with the view to reducing the frequency of stope blasts, improving stope stability, productivity and ultimately improving overall stope performance. A key aspect in the ability to undertake underground mass blasts of this scale is the application of i-konTM electronic initiation technology by Orica. In the past two years in excess of three million tonnes has been initiated utilising this electronic technology, with an average blast of 250 000 t ranging to the largest to date being 580 000 t. By providing flexibility in blast designs, the use of electronic detonators has allowed mass firings over multiple sublevels. This has resulted in a significant reduction in stope extraction steps compared to conventional pyrotechnic firings. The benefits of this reduction in the number of stope blasts are wide ranging from improved stability of interim stope voids between blasts, reduced blasthole damage, improved blast vibration management and reduction of complex changes to ventilation systems for blasting.

Jan 1, 2004

Historically BHP Billiton Alliance Coal Operations Pty Ltd (BMA) have generated resource models from widely spaced data points (drill holes). The accuracy of these models has been influenced by the degree of local structural disturbance of the coal seams and by the choice of interpolators used in the modelling process. In some circumstances unacceptable vertical errors of up to 10 m have been observed whilst mining. New terrestrial photogrammetry or laser imaging technology now allow the 150 or so kilometres of exposed highwalls in BMA to be rapidly, accurately and safely mapped and the three-dimensional images economically incorporated into resource models, reconciliation grade control models, drill and blast designs and for pit stability analysis.

Jan 1, 2005

By K Biegaj

The paper describes challenges the author has encountered on Australian underground gold and nickel mines over the last eight years, when recovering high-grade gold/nickel bearing mine floor material with a mobile supersucker/giant vacuum cleaner and other equipment. Whilst for a number of years the mine floor vacuuming and other mine floor clean-down technologies have been accepted/adopted and are working well in other parts of the world and on the South Australian opal mines, regrettably, they have not yet gained acceptance of mining executives and mine managers of gold and metal mines in Australia, who still elect to leave the never to be recovered gold/metal behind or to put it plainly - waste it.For reporting purposes during the mining process, the portion of gold/metal included in calculation of ore reserves prior to obtaining capital funds for their development, continues to be camouflaged in various reconciliation and call factors. This approach, ie wasting of capitally developed and already broken ore stocks should be viewed by the shareholders as totally inappropriate to say the least, especially with the current gold and other metals prices.The author attempts to provide answers as to why the technology referred to above has not yet been accepted on Australian gold and metal mines and outlines the way forward.CITATION:Biegaj, K, 2012. Why do shareholders and mining executives allow mine managers to leave behind high-grade broken ore underground?, in Proceedings Narrow Vein Mining 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By A Sellgren, M R. Carstens, R Visintainer

There is a wide variety of industrial pastes or non-settling slurries pumped in mining, dredging and reclamation projects as products, refuse and tails. The types and/or names of some of the common ones are alumina red mud, phosphate clays, tar sands mature fine tails, tar sands (CT) consolidated clays and fly ash. The pipeline performance or friction of these varies dramatically with the type, its concentration and the particulars of the actual slurry making it difficult to select pumping equipment and to design associated pipelines. The GIW Hydraulic Laboratory in Grovetown Georgia has tested a number of these slurries over the last 30 years for various mining customers. Where available in the public domain and/or where permission has been obtained, the results of those tests are presented in this paper in a form usable for pipeline and pump system designers and users.

Jan 1, 2005

Carbothermal Reduction and Nitridation of Ilmenite Concentrates and Chlorination of the Reduced Samples

Sep 13, 2010

This paper presents a method for estimating the strength and stability of model coal pillars with bedding planes (weakness planes) inclination. The strength of coal relative to the angular difference between the principal stress direction and bedding planes is considered. The failure behaviour of model coal pillars containing weakness plane inclination by using servo-control Schenck Machine are shown. Uniaxial and triaxial compressive strength of coal specimens are investigated, and test results indicated that the strength of coal pillars depends on the weakness planes inclination with respect to the principal stress direction. However, it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of the coal specimens is reduced. An empirical method is given for prediction the compressive strength of coal containing weakness planes inclination. The results of this method are compared with the experimental results and Jaeger theory. Finally, three well-known empirical strength criteria were tested against the triaxial test data for coal containing weakness planes inclination.

Jan 1, 1995

The occurrence of metallic minerals in Australia to the time of the proclamation of South Australia as a Colony in 1836 was unknown. It is, therefore, perhaps, surprising that British settlers arriving in the Coromandel included among their number a German scientist Johannes Menge who had been appointed by the South Australian Company to the post of Mine and Quarry Agent and Geologist on 1 July 1836. His instructions were to `explore the natural productions of the Colony above and below ground and to superintend the working of quarries of stone and slate, the boring for water, metal, lead, coal and other mines at a salary of ú150 per annum for one year and for as much longer as the Company require your services not however exceeding five years'. In the event, he was to have little influence on those matter.

Jan 1, 1993

By S M. Mousavi

The issue of estimating evaporation in soils is central to the design of engineered soil caps for mine waste and landfill applications. In general, because evaporation from the soil is difficult to measure in the field, laboratory experiments and empirical methods have been used. Much of the earlier work has been conducted in soil science, although in recent years, geotechnical and geoenvironmental engineers have given great deal effort to this work. The result of this increased interest is the development of numerical models, such as UNSATH and SoilCover for estimating evaporation. In this study laboratory-measured evaporation from soil columns was compared with evaporation predicted using the computer program SoilCover, and the analytical method proposed by Gardner and Hillel. Good agreement among the results was observed. Also the sensitivity of the predicted evaporation to soil hydraulic and geotechnical properties, such as saturated hydraulic conductivity and coefficient of volume change was discussed and the practical implication of the sensitivity were highlighted. The work has application in the design and construction of soil covers over sulfide-bearing mine waste and landfills.

Jan 1, 2003