Search Documents

By P J. Fairfield

"This paper reflects on the author’s experiences in undertaking mining studies and reviewing mining projects and technical reports, particularly over the past five years, and the impact of recent changes in reporting standards and listing requirements pertaining to mining-related evaluation and valuation exercises. It also discusses contemporary changes in the expectations of the investment community and the implications for the role of the technical specialist in providing advice to such stakeholders.Not for the first time in history, the resources industry has experienced a significant downturn after a period of strong, sustained growth in line with the traditional view of the cyclical nature of commodity markets. The resource industry is currently faced with capital austerity in the wake of projects ‘failing’ (not delivering to expectations). In response, the industry has experienced changes in investment behaviour (slowing of investment) and an increasing regulatory burden as stakeholders seek a greater understanding of mining project risks.This paper discusses this response and uses case studies to highlight the key learnings (perhaps re-learnt) by the industry. It also discusses the challenges faced by technical specialists in communicating the results of technical and valuation studies to the investment community.As investors seek to take advantage of the current stage in the investment cycle, the key challenge of the technical specialist is to effectively communicate the uncertainty in technical assumptions, risks and opportunities that drive project value.CITATION:Fairfield, P J, 2016. Managing expectations – from buyer beware to buyer be aware, in Proceedings Project Evaluation 2016, pp 66–74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

Direct measurements of liquid contents in foams obtained from (x-terpineol a-T) n-pentanol (AmOH) and n-octanol (OctOH) solutions were carried out using a column of special construction. The column enables to determine the liquid contents by cutting-off foam layers of various thicknesses and measuring amounts of liquid contained in the cut-off foam layers. Liquid contents in the whole foam layers, in the top foam layers of thickness 14 ¦ 1 mm and distribution of water alongside foam height were determined. The average liquid contents were high and reached a level of 30, 35 and 40 per cent for foams formed from cc-T, AmOH and OctOH solutions, respectively. The liquid contents in the top foam layers were much smaller. They were of an order of five per cent for a-T and AmOH and 12 per cent for OctOH. On the basis of the liquid distribution alongside foam height some practical conclusions concerning possibilities of minimising amounts of liquid contained in the collected concentrate are presented.

Jan 1, 1993

By Y D. Jeon, K S. Kim, C-H Eom, C M. Yoon

The carbon neutrality continues to require reduction of carbon usage in ironmaking and steelmaking processes. Specially, it is expected that the hot metal ratio (HMR) in the steelmaking process should be reduced essentially. Unfortunately, the reduction of the HMR in converter can bring about poor environment for nitrogen removal from molten Fe. From this situation, nitrogen prediction model has been developed to understand the fundamental of behaviour of nitrogen and quantitatively interpret its content changes in the converter process. Thermodynamic and kinetic approaches were improved based on existing mathematical model and attempted to predict nitrogen content in realtime by combining process data. In present study, heat supply from the oxidation (mainly carbon and silicon) and CO evolution in the converter are considered, and scrap melting due to the heat transfer from the molten Fe to the solid scrap charged in the converter also be considered.

Aug 21, 2024

The preferred alternatives in heap design and their motivation are identified as- -normal heap leaching, to be generally applied wherever possible, - flooded vat leaching, to be appliedwhere wetted ore lacks adequate cohesion or if limited space necessitates it,- thin layer leaching, to be applied where deleterious vat chemistry necessitates it.A number of the following features would probably be incorporated in the optimization of normal local heap leach operations- pre-cyanidation - pre-agglomeration - retaining walls- staged (counter-current) heap treatment- control of calcium levels- reduced pH and trickler irrigation

Jan 1, 1984

Twelve years ago, Jeffrey Mining Machinery Division of Dresser Industries Inc. developed the 120H HELIMINER. This machine was the world's first fixed-drum continuous miner and soon became the standard among manufacturers of continuous miners throughout the mining machinery industry. This paper will first outline a brief history of continuous miner development, then discuss significant parameters which are essential to a successful continuous miner design, and finally describe a number of specific applications of Jeffrey continuous miners in a variety of materials, such as coal, potash, iron ore, and trona, around the world.

Jan 1, 1978

By I Testrow, M Wiggin

Scrutiny of the whole explosives industry has increased as a result of the terrorist attacks on the World Trade Centre and the Pentagon on 11 September 2001 and the bombings in Indonesia, including the Bali bombings last year. This has been highlighted in specific press releases from governing bodies, like the Department of Mineral and Petroleum Resources û Western Australia, on the necessity of being in compliance with regulations for storage of explosives. As a result, audits by inspectors to assess compliance are to be expected. In a proactive move, DynoConsult has assisted several customers through benchmarking current practices, in order to identify any areas of non-compliance to the statutory requirements for explosive storage and security. This paper discusses the outcomes of supplier discussions and customer audits and highlights the implications for the industry.

Jan 1, 2003

By W A. Peppin, D N. Riley, N W. Schulenburg

In June 2008, a joint airborne collection using hyperpspectral systems was tested on a single Twin Otter aircraft. This experiment was designed to incorporate two airborne hyperspectral sensors for geological and environmental projects. Mineral exploration and environmental impact statements are two areas where full spectrum hyperspectral data can document the mineralogy at the surface prior to mining operations. Many previous hyperspectral remote sensing collections were collected on a single aircraft with a single sensor. Mineral mapping using hyperspectral sensors that measure in complimentary regions of the electromagnetic spectrum is cost effective as it allows for the mapping of clays, sulfates, carbonates, feldspars, quartz, garnets and many other minerals. This report describes the experiment using the following two hyperspectral sensors: ProspecTIR, a visible near and shortwave infrared (VNIR-SWIR) sensor with 356 channels and spectral range of 0.4 to 2.5 ¦m, along with a spatially enhanced broadband array spectrograph system (SEBASS), a midwave and longwave infrared (MWIR-LWIR) sensor with 128 channels from 2.5 to 5.3 ¦m and 128 channels from 7.6 to 13.5 ¦m. SpecTIRÆs ProspecTIR system and The Aerospace CorporationÆs Spatially Enhanced Broadband Array Spectrograph System (SEBASS) are pushbroom sensors, have high signal to noise ratios, have similar swath widths and instantaneous fields of view. Examples of data collection experiment will be shown with a focus on mineral/lithologic identification and mapping along with environmental assessment in the western United States. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Y Akiti, J Moller, E Esper, R Rugolo, A Pains

"Morro do Ouro Mine is a high tonnage/low-grade mine located in Paracatu, Minas Gerais State, Brazil. The mines move around 55 Mt of ore per year at an average grade of 0.4 g/t. The auriferous mineralisation of Morro do Ouro is related to hydrothermal fluids rich in arsenic (As), gold (Au), lead (Pb) and zinc (Zn). These percolated along favourable structures contained within phyllites of Upper Proterozoic age and defined a mineralised megaboudin which outcropped with 4 km extension and up to 2 km in width. The litologies in the interior of this structure are typically more deformed, sericitised and sulfidised, and exhibit the development of quartz boudins in the centre of the more deformed zones where are found the higher Au grades and the coarser sulfide crystals. Gold is preferentially associated with arsenopyrite, mainly occurring in fractures or aggregations of crystals and is rarely in solid solution or refractory. Over 90 per cent of the gold contained in the sulfide ore is free or extractable by cyanidisation. The current mineral reserve is 17.9 Mt at 0.403 g/t published at the end of 2012.In order to get a good grade estimation that represents the orebody more accurately a solids methodology was used to distinguish the different orebodies. Before 2011 the orebodies were worked with two domains relating to the weathered mantle. The B1 ore, which is oxidised, is located at the top of mineralisation, and is used to feed Plant 1. Underneath B2 ore, which is fresh sulfide bearing, represents over 30 years of production in Plant 2.In order to improve the predictability of gold grade estimation in geological modelling and to get a better predicting behaviour of each domain on the deposit, studies were carried out in which it was possible to show a correlation between elements and the mineralisation. One strong correlation and spatial distribution between Au and As, As and sulfur (S), Au and Pb, Au and Zn were found.Based on geochemistry, mineral correlations, amount of sulfide, structural deformation, texture of sulfides and the daily experience of the mine, it was possible to create solids that individualised bodies with similar mineralogical and chemical characteristics using the parameters listed above.After 2011, a new modelling concept was proposed and built with 11 different domains, compared with the previous, and with two more parameters: recovery acid neutralised capacity (ANC).Each of these bodies have different behaviours in mineral processing, like flotation and metallurgy. For example, bodies with pyrrhotite bring problems in the flotation, bodies with high arsenic do not recover well, bodies with high As with coarse texture have good recovery, bodies with fine texture do not have good adherence in production.In the present state of knowledge, protocols are being developed for bench testing to predict the recovery of each geochemical domain aiming to include these in the geological model for the parameter recovery. It is intended to create a field throughput in the model of ounces per hour, from each block of each domain to better predict the production, using the parameter recovery, Au and Bond Work Index (BWI).CITATION:Esper, E, Rugolo, R, Moller, J, Akiti, Y and Pains, A, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 67-74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By T Brown

Australia is now committed to the most significant period of infrastructure investment since the 1960s and the current climate of project finance and public private partnership (PPP) model uncertainty means it is imperative that the affordability and certainty in delivery of infrastructure projects is maximised.In light of the current and forecast levels of infrastructure investment it is worth drawing comparison with a similar period of Australian expansion when the nation’s first railways were constructed. Similarly to over a century ago, we are following a trend in rapid development and are already reaping the inefficiencies that could be avoided with broader technical planning and improved client coordination.The original rail networks were developed by the individual states before they combined to form a Federation of states in 1901. As a result of the adoption of different gauges by 1917 a passenger wanting to travel by train from Brisbane to Perth had to change trains six times.Similarly in 2011, there is little parity between Australian states on the quality requirements (performance specifications) for road tunnels. Differences between states start most significantly with the size of the specified traffic envelopes, thus the size of tunnel required. Where ambiguity and differences exist in project documentation, performance specifi cations (PS) and broad technical requirements for road tunnel projects, any associated risk in interpretation ultimately ends up being incorporated in the bidder’s (constructor’s) final sell price.Whilst not nearly as inconvenient as having to change train at each state border, and largely unnoticed by the general tax paying motorist, this paper examines examples of apparent minor differences in Australia’s recently constructed road tunnels to highlight the differences in road tunnel specifications.The paper identifies how these small differences manifest themselves in major price penalties between projects and further, highlights the need for further specification review, refinement and standardisation across road tunnel jurisdictions to increase road tunnel affordability.

Mar 8, 2011

By J Jackson, K Nguyen, A Nguyen, E Manlapig

"With the recent advancement in drill core imaging systems, a large volume of high resolution drill core images can now be rapidly collected and mineralogically classified. This paper introduces a novel semi-automated method for rapid prediction of process engineering parameters from this type of image. The aim is to allow for a rapid and low-cost assessment of the ore processing variability within a mineral deposit with a reduced amount of metallurgical test work. This method will see its application primarily in the project evaluation phase, where proper evaluation of the processing variability of the orebody normally requires a prolonged and costly metallurgical test work program. Applying this image-based texture analysis method on the mineralogical classified drill core images, the ores are classified according to their textures. For each engineering parameter, a small number of physical test work is required to produce a data set for training and testing of the predictive model. The paper also presents a case study in which this method has been applied to predict the A*b parameter used in mineral process plant design.CITATION:Nguyen, A, Jackson, J, Nguyen. K and Manlapig, E, 2016. A New Semi-automated Method to Rapidly Evaluate the Processing Variability of the Orebody, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 145–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The Callie Underground Gold Mine (Callie) is owned by Newmont Asia Pacific and located 531 km north-west of Alice Springs in the Northern Territory. Historically, stopes have been mined utilising a primary and secondary stoping sequence with cemented aggregate fill and rock fill respectively. Current and near-future mining will employ long hole open stoping with rib pillars and rock fill with a paste fill system approved to allow a higher extraction ratio from mid-2011. The Callie rock mass is of good quality with little or no mining difficulties during development and stoping to a depth of 1140 m below surface. Development is currently occurring at depth of 1360 m below surface. Stress damage previously observed only in secondary stope accesses is now observed in development unaffected by stoping stresses. A change in rock mass properties is being experienced with depth, with more pronounced and frequent joint planes. Also, other structures are intersected more commonly, such as lithological boundaries and fault zones. The 'Callie rock factory' mentality that has persisted for years is challenged. This paper covers an appraisal of the stress and ground condition changes at Callie. The appraisal outlines the mine design criterion that was developed and examines the transition from a low stress environment to one where stress damage is observed. Discussion includes a judgement on the rock mass damage observed in development, the dominant geotechnical factors influencing the change in ground conditions, and if a correlation can be made between the observed rock mass damage with stress through the use of numerical modelling.

Nov 25, 2010

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By S M. C Verryn

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis of metallurgical products. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine process control. Knowledge of the crystal structures of the major phases is essential for Rietveld analysis, and these are well known for most minerals and major phases in metallurgical products. It provides the basic structural information necessary for the determination of mineral stoichiometry and for elucidating solid solution behaviour. Modern methods, such as simulated annealing and charge flipping, permits the determination of crystal structures from powder data. Unit cell data can be used where conventional microchemical analysis is unable to provide an answer to the extent of solid solution in ilmenite roasting. Unit cell data (by XRD) is used to determine the amount of roasting necessary for the development of magnetisation to be able to separate chromite from an ilmenite concentrate. Phase quantification is probably the most widely used application of XRD analysis. It is used for materials balance in the minerals and cement industries, and it is finding novel applications in the iron and steel industry. Applications of XRD in high-temperature metallurgical processes are increasing. In this paper the phase chemistry of iron ore sinters, the evaluation of subsolidus reactions in titania slags and the identification of furnace accretions are discussed. Despite the success of the Rietveld method in phase quantification, the method still needs further development in the quantification of closely related or polytypic phases. The quantification of pyrrhotite phases using various Rietveld programs still gives ambiguous results. This is also true for the different SFCA phases in iron ore sinters. Clearly the analysis of similar phases, differing only in the presence of weak superlattice reflections is still problematic.

Jan 1, 2008

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

By W Potma, C Brauhart, S Halley, S Urbisinov, A Scogings

Truly integrated, quantitative, 3D GEOmetallurgical (or mineral system) characterisation, classification and 3D modelling should provide a cradle to grave unifying link across the exploration and mining value chain. All too often, spatially representative (quantitative) characterisation and modelling of a mineral system is delayed until feasibility stage, incurring a significant opportunity cost. The application of robust GEOmet characterisation methods early in the project lifecycle (at exploration stage) improves ground selection, exploration, and Mineral Resource estimation outcomes, long before there is a need for metallurgical test work. The value of this early provision of quantitative 3D mineralogy models is compounded at project feasibility stage, and continues to accrue over the entire project lifecycle, delivering cost savings, improved decision making and early warning of issues and opportunities.CITATION: Potma, W, Halley, S, Scogings, A, Urbisinov, S and Brauhart, C, 2018. Putting the ‘GEO’ back in front of GEOmetallurgy: importance of early implementation of quantitative mineral system characterisation, classification and modelling, in Proceedings Complex Orebodies Conference 2018, pp 55–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Y S. M Tabatabaei, R Hosseini Tabata

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulfide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A ferrooxidans was used to change the surface chemistry of pyrite and copper sulfide ores and consequently, their flotation behaviour. In the presence of A ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulfide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria could be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50 per cent lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

By J W Shields

The aim of this paper is to present a concept or model regarding a particular geological environment where gold orebodies occur in the Pine Creek Geosyncline and indeed in many other pans of the world. The name GIGIACS (an acronym for Gold In Greywacke In Anticlinal CrestS) is proposed to label this concept or model. The name Saddle Reefs (which has been in use for many years) is used for gold-bearing quartz veins which often occur in conjunction with Gigiacs. Simple patterns formed by this type of mineralisation at the surface due to different configurations are illustrated. Some examples of Gigiacs and associated saddle reefs are presented from the Pine Creek Geosyncline together with examples from other parts of the world. This concept has been used successfully as an exploration tool and five examples are given. The terms Gicsiacs (for Gold In Carbonaceous Shale In Anticlinal CrestS) and Giliacs (for Gold In Limestone In Anticlinal CrestS) are also used.

Jan 1, 1994

By Q Zhou, H Nordberg, W Wang-Geissler

Efficiently controlling foam/froth within mineral processing continues to pose a challenge to the mining sector. The foaming characteristics of aqueous solutions for two-phase systems of air/liquid are well-studied with theories and mechanisms proposed to describe and predict foam formation and stability. The types and structures of reagents that either promote or prevent foaming/froth formation and stability are well-defined in these studies and practiced across various applications. Three-phase systems of air/liquid/solid, such as froth from mineral slurries, however, pose a challenge with the presence of a large quantity of relatively fine mineral particles. Theories and mechanisms that rationalise the effects of chemical additives as a defoamer or foaming agent in aqueous can be applied as a general rule, but do not provide the most effective solution for mineral slurry systems. Silicone-based defoamers, particularly their O/W emulsions, have been widely and successfully used at various stages of mineral processing to efficiently control the mineral slurry foaming properties. However, their foaming control ability could be significantly impacted by different processing aids used during the upstream process. In a zinc-rich mineral system, a silicone-based defoamer starts losing the properties necessary to effectively control foaming in the leaching circuit when throughput is increased. In this study, the synergistic defoaming/anti-foaming effects from surfactants and silicone-based defoamers are discussed to effectively control foaming/froth in the zinc leaching circuit, even with lower total defoamer dosage. Improvements during mineral processing can also lead to a cleaner mineral grade by reducing waste.

Aug 24, 2022

By Taylor GP

Mining Lease SML 57 was registered to Mount Kasi on 5 January, 1995. The Mount Kasi gold mine is located in Vanua Levu, Fiji's second largest island and operated from 1932 to 1946 producing 261,000t of ore at an average grade of 7.5g/t Au. The deposit represents a structurally controlled style of high sulphidation copper gold mineralisation with peripheral low sulphidation mesothermal vein type gold mineralisation. The resource consists of 1,048,000 tonnes of residual soils (eluvium) containing 1.9 g/t Au at 0.5 g/t Au cut off and 1,240,000 tonnes of hard rock at 3.0 g/t Au and 1.0 g/t Au cut. 94 drill holes, 298 auger holes and 85 pits were modelled to outline the resource. 29% of the pits bottomed in mineralisation and it is likely the full thickness of eluvium has been understated. The pit is scheduled to produce 500,000 tonnes of ore per annum to yield 35,000 ounces of gold with an initial 2 years of eluvial ore followed by a further 2 years of hard rock ore. Total capital costs are estimated to be less than 10.0 million dollars with construction planned to commence in 1995. The likelihood of locating further ore is high.

Jan 1, 1995