Search Documents

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By Kaji S

The Tsugaru Tunnel, located on the Honshu island approach to the Seikan Tunnel, is 5,880 m long and has a "Shinkansen" cross section of 90 m2 area. The geological formation through which the tunnel passes consists of very soft rock most of which is unsolidified sandstone belonging to the Neogen. The permeability coefficient is in the range of 10-2 to 10-4 cm/s and being water bearing with a high ground water level, the ground is unstable and subject to soil outflow phenomenon. Kajima Corporation, undertaking the Futamata Construction Section (1,420 m long), excavated the tunnel by the upper half heading method with side pilots employing the following countermeasures to cope with these severe conditions.

Jan 1, 1987

By Shinnosuke U, Zhang HE

In this paper, it is shown that the higher the pre-activation concentration of copper ions in pulp, the larger the adsorption amounts of copper ions and xanthate on arsenopyrite surface, and the better the arsenopyrite flotability in strong alkaline medium. On arsenopyrite pre-activated with cupric ions, the xanthate adsorption density in strong alkaline medium is approximately equivalent to that of cupric ions. It is therefore concluded that an amount of copper ions adsorb on arsenopyrite surface first, and then an amount of xanthate can (and only can) adsorb dependently on the surface active sites produced by these adsorbed copper ions on the mineral, so that arsenopyrite is kept rather flotable and is hardly separated from pyrite even in very strong alkaline medium. Selectively wiping out the surface copper active sites on arsenopyrite is the key point of successful separation of pyrite from arsenopyrite. According to this theory, a new 'SZLI' (know-how) method was recommended to satisfactorily deal with the difficult separation.

Jan 1, 1993

By C A Heinrich, Jaques A. L, L A I Wyborn

Most orebodies have cross-sections of less than I km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defmed as 'all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated form and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system offluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: I. sources ofthe mineralising fluids and transporting ligands; 2. sources ofthe metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common through

Jan 1, 1994

The Warraua and Mount Poole Inliers form part of a discontinuous series of basement complexes in the northwestern corner of New South Wales. The Inliers comprise mainly clastic sediments of low metamorphic grade (Wonominta Beds) and minor sills, dykes and intrusives, particularly within the Mount Poole lnJier. The Warratta rnlier has received attention due to the occurrence of auriferous quartz-veins where reef mining activities havetaken place.The deformational history of the Warratta and Mount Poole Inljers is characterised by a continuous subhorizontally WSW-ENE directed compression. Deformation was associated with the development of NNW-trending and steeply west-dipping major faults, which bound or biscct the inliers. Chevron folds and a penetrative axial planar cleavage characterise the deformational architecture and document crustal shorterung of at least 40 per cent. In zones adjacent to the major faults and within pelitic and semi-pelitic uruts, a multiple deformational evolution becomes apparent, comprising two events (D1 and D2). Deformational structures considered significant in this study were the result of D1. Tight, northeast-vergent fold patterns FI' and associated axjal plane cleavage SI' and reverse dip-slip movements at major faults indicate early northeast-directed thrusting during D1. This was followed by dextral strike-slip deformation displayed by tight, recumbent folds, en-echelon fold patterns (F2'), a northeast trending crenulation cleavage (52'), and two sets of second order faults, the latter showing high angular relationship to the major faults. A final stage of the deformational history (D2) is represented by WSW-ENE trending kink folds (F2).Auriferous quartz veins, predominantly occurring within pelitic and semi-pelitic units, were generated syntectorucally during the early deformational event (D1) in the course of commencing development of cleavage (S2'). Vein textures point towards vein formation by repeated hydrauJjc fracturing and fracture healing (crack-seal process), and by simple accretionary vein growth. Folded pelite-dominated horizons, considered as low permeability units, are suggested preferential sites where migrating metamorphic Ouids pooled and were trapped, causing high fluid pressure.Hydraulic fracturing and vein precipitation was controlled by lithology and structural constraints such as cleavage.K-Ar dates of approximately 440 Ma (Benambran Orogeny) marking the peak of metamorphism, and coinciding with the development of cleavage S1', also indicate the time of auriferous quartz-vein formation. A period of deformation of at least 30 Ma is proposed for the development of cleavage S1', as constrained by K-Ar dating and the intrusion of a syntectonic granitoid, the Tibooburra Granodiorite.

Jan 1, 1992

By J Robertson, D Williams, H D. Plewes

The co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material (Co-Mix) with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retaining capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimise acid generation and metal leaching. When compacted, Co-Mix materials have low volume change characteristics with respect to total stress and matric suction together with high shear strength. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures or a full depth waste repository. The theoretical properties of Co-Mix blends are investigated. The results of a laboratory program to characterise the physical and hydraulic properties of co-mixed tailings and waste rock are presented. Various ratios of tailings were blended with different waste rock materials. Hydraulic conductivity tests were conducted at confining pressures ranging between 0 and 400 kPa. The saturated hydraulic conductivity for the Co-Mix materials was found to vary between 4 + 10-5 m/s and 5 + 10-9 m/s depending on blend ratio, waste rock type and confining pressure. These results together with other physical properties show excellent hydraulic and strength characteristics can be achieved for Co-Mix materials.

Jan 1, 2003

By Fourney W. L, Dick R. D

Tests were conducted in plexiglass and Rockite models to determine if crater blasting could be improved by changes in charge geometry or by alterations to the borehole. Circumferential grooves were placed at various locations in the borehole in an attempt to control the initiation site of the crater. Grooves located at or above the top of the cylindrical charge had no effect on the resulting crater. Grooves placed too low in the borehole were successful in controlling the initiation site but the growth of the fracture system was not sufficient to reach the upper surface. Grooves located at a height of two thirds of the charge length were quite successful in that resulting craters were bigger by at least a factor of six than the normal crater. Testing was conducted in Rockite models to investigate charge geometry. Spherical charges in ungrooved boreholes resulted in crater sizes that were three times larger than those caused by cylindrical charges.

Jan 1, 1990

By M McDonald

KiwiRail has a goal of significantly improving passenger rail services to west Auckland, as part of its DART (Developing Auckland’s Rail Transport) suite of projects. The New Lynn Rail Trench (NLRT) project was a significant component of this work. The NLRT project facilitates essential doubletracking of the Western Auckland line, and provides a new commuter transportation hub within a busy town centre.The 1.5 km stretch of track through the New Lynn town centre has bisected the township for over 80 years. Double-tracking the line provided the opportunity to grade-separate road and rail, which would help to re-connect both sides of the township and enhance public amenity and safety.KiwiRail employed an Early Contractor Involvement (ECI) procurement model engaging a consortium comprising Fletcher Construction, Beca Infrastructure and Synergine to develop a Design and Construct solution.With weak soil conditions and high groundwater levels, a diaphragm wall construction method to form the trench walls was selected as the best solution. Further challenges to construction included working within a narrow rail corridor constrained by buildings along much of the boundary, and a requirement to keep the existing line open for rail services. Detailed construction planning was required to ensure rail and construction safety in a constrained space whilst building the trench walls, propping these walls during excavation, and constructing the base slab in the most efficient way possible.This paper will detail the geotechnical conditions and the additional constraints that made this rail trench a challenging structure to design. It will also describe the fi nal design and construction methodologies that were employed, that allowed very successful completion of the project.Additionally, this paper will review the design and construction lessons applicable to the current Victoria Park Tunnel project, and indeed for all future cut and cover tunnel projects in the Auckland isthmus.

Mar 8, 2011

Following the Moura No 2 Wardens Court of Inquiry and subsequent changes to the Queensland Mining Legislation there is a requirement in Queensland coal mines for: a person with the recognised competencies to be appointed at each underground coal mine to the position Ventilation Officer; and the person is directly responsible for the implementation of the mine ventilation system and for the establishment of effective standards of ventilation for the mine. The Regulations require that an underground mine must have principal hazard management plans that provide for at the least the following: emergency response, gas management, methane drainage, mine ventilation, spontaneous combustion, and strata control. Other than strata control all the plans require the ventilation officer to have roles and responsibilities to develop, control, monitor and undertake actions in relation to these plans.There are also another 34 Regulations that either directly or indirectly requires the Ventilation Officer to take actions.The purpose of this paper is to outline the information that the regulators look for in sealing plans and the actions the regulators will take if the sealing does not go to plan (TARPs being exceeded).

Jan 1, 2005

By T Gartner

This paper describes the design, manufacture and site services associated with the supply of mine hoists for the new mine under construction by Falconbridge Limited in Ontario, Canada. Two new shafts are being sunk, and the hoisting equipment at each shaft can be summarised as follows: Ventilation shaft:4.66 m diameter double-drum second-hand hoist, originally in operation at San Manuel Mine, Arizona, to be used as the shaft sinking hoist. The second-hand hoist presented a challenge in that during its previous life, the hoist had been intensively operated during service at San Manuel Mine, and this paper describes the scope of refurbishment work undertaken, both electrically and mechanically, to ensure future reliable operation, together with the requirement to meet Canadian and Ontario regulations and codes of practice. 3.05 m diameter new single drum auxiliary hoist to be used as a second means of egress. Main shaft:4.57 m diameter new double-drum hoist to be used initially as the shaft sinking hoist, and subsequently to be converted to the equivalent of a single-drum multi-rope hoist for service duties during the production phase; 5.49 m diameter new double-drum hoist to be used for skip hoisting during the production phase; and 3.05 m diameter new single drum auxiliary hoist.The new hoists are all designed to comply with SABS requirements such that hoisting with reduced rope safety factors will be possible in the future. This paper describes the principles involved both mechanically and electrically. Particular attention is paid to the conversion of the main shaft service hoist from a double-drum sinking hoist to a multi-rope hoist.This paper describes the ac electrical powertrains (drives and motors) used that eliminate the need for harmonic filters and reactive power compensation equipment since they exhibit no negative effects on the utility electrical network system. This paper describes the logistical challenges of installing, commissioning and setting to work a series of five hoists in a short time frame.

Jan 1, 2005

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By S Khadhraoui, T Yusuf, C Kirmse, E Hecker, R Degel, A Akouch, N Borowski, M Reuter

For an optimal design and control of metallurgical processes, a deep understanding of the thermodynamics of the governing reactions is required. Modelling the thermochemical behaviour of those reactions is complex, as it involves multi-component and multi-phase systems. For this purpose, thermodynamic computing systems such as FactSage™ (Bale et al, 2016), which combine Gibbs energy minimisation routines with large databases of optimised thermodynamic data of solutions and compounds, have been used within the SMS group GmbH. Recently, the successful integration of those thermodynamic computing systems into the digital platforms of SMS has been achieved through ChemApp, which made running complex thermochemical calculations in Python-integrated development environments possible. ChemApp is a programmer’s package for thermochemistry and incorporates the Gibbs energy minimiser of FactSage™ as reported by Petersen and Hack (2007) as well as by Zietsman and Petersen (2018). The digital platforms link the fundamental and the industrial aspects together and can be applied as a process advisor, or for the evaluation of the environmental footprint and the economic implications of different process routes, as discussed by Reuter (2023). Two examples illustrating the progress of the developments in this regard will be introduced: 1. The Tilting Refining Furnace (TRF) for copper scrap recycling and refining to anode copper (the BlueControlApp). 2. Dephosphorisation control for the oxygen steelmaking process (Basic Oxygen Furnace (BOF)).

Jun 19, 2024

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

By P Dean, M Elmouttie

Radar monitors are now widely used in surface mining for monitoring slope deformations and predicting failure events. Their introduction has facilitated better management of risk associated with slope failure during mining and therefore protection of personnel and equipment. However, a wellrecognised problem is that radar monitors only measure deformation directed towards the detector (line-of-sight bias). This bias can lead to misinterpretation of deformation size, rate and failure mechanism, and therefore miscalculation of failure volume, which can significantly impact safety and productivity. This paper presents recently completed research and field trials into the feasibility of using low cost vision systems to mitigate this issue. It has been demonstrated that by integrating a computer vision system with an existing slope monitor, high precision tracking of features in the field of view can be performed. Combined with assumptions on the deformation characteristics, the true 3D deformation vector can be estimated. The applicability of using this technique for monitoring iron ore mine slopes is discussed.

Nov 8, 2021

Over years of exploration the massive and tabular orebodies in the area to the South West of Western Areas Gold Mine had been assessed as containing about 50 million ounces of gold û a world class orebody. Planning initially was for a surface and subvertical shaft system to exploit this area but because of cost, a single lift shaft to an area which could be accessed ex Western Areas was planned to intersect the reef at 2760 metres. It was also planned to mine out the shaft pillar area long before the deep shafts would reach that position. This is not the normal practice in South African Gold Mines. The stoped out shaft pillar was backfilled to minimise movement in the shaft sites. The result of a competitive tender/adjudication process was that Cementation Mining û Skanska won and was awarded the R192 million contract to sink the Main and Ventilation Shafts on 15 June 1995. On 1 April 1999 Western Areas and Placer Dome SA formed a Joint Venture, which now owns and operates the mine on which the South Deep Shafts are situated. This situation prevails today.

Jan 1, 2002

The Closure Risk model was developed as a new tool to aid decision makers in the complex area of mine closure. It uses a simple analytical technique that allows the decision maker to simplify what is often a complex mine closure process into more easily managed sub components. This systematic approach ensures that critical factors in the closure process are not overlooked. It also allows the most important issues to be highlighted. The model can also be used to produce quantitative estimates of risk by weighting and prioritising the issues to produce the Closure Risk Factor (CRF). Field trials at several mine sites in the Northern Territory of Australia in 2001 tested the model. The trials confirmed that the model has significant potential as a tool for decision-makers to assess in a structured, systematic manner, the major closure risks at individual mine sites. The risks include not only environmental impacts but safety and health, community, legal, financial, technical and other issues. The trials confirmed the value of a team-based approach and the inputs of key staff including environmental, production, mine planning, and community liaison personnel as well as mine management. Although the usefulness of the qualitative component of the model was established, it was found that, due to the influence of subjectivity, the utility of the prototype model to determine quantitative risk was of limited value. Using a continuous improvement approach, improvements to the model were sought. A refined model, incorporating the Australian Standard 4360 definition of risk and facilitated in-house risk assessment sessions was developed and tested against the data obtained in the field trial. This model, while maintaining the qualitative strengths of the original, allows more accurate absolute and relative quantitative scores to be calculated. This in turn facilitates comparisons between the issues at a single site as well as between different mines.

Jan 1, 2003

By R Herbert, M E. Malmstr÷, S U. Salmon

The study focuses on sulfide oxidation processes in unweathered pyrite-rich mine tailings from a soil-covered impoundment in northern Sweden. To simulate the oxygen-limited conditions in water saturated tailings two long-term column experiments were performed. Results are presented for the first 11 months of the experiments at room temperature. The tailings used in the experiments were of two different grain sizes (one coarse grained, in the range 0.02 - 0.6 mm with a grain surface area of 1.86 m2 g-1, and one fine-grained, in the range 0.0015 - 0.06 mm with a grain surface area of 10.00 m2 g-1) and with slightly different mineralogical composition. The S:Fe molar ratio in the leachates (1.0 - 1.5) indicates either that pyrrhotite is the main iron sulfide undergoing oxidation in our experiments, or, alternatively that the S:Fe molar ratio in the leachate is determined by pyrite weathering in conjunction with other processes releasing iron or immobilising sulfate. However, speciation modelling of the leachates indicates that ferrihydrite was close to saturation, suggesting that a ferric oxyhydroxide may have dissolved/ precipitated during the experimental period, thereby affecting the S:Fe molar ratio. Pyrite oxidation rates obtained from the two column experiments during æsteady-stateÆ were 2.25 + 10-13 and 8.45 + 10-14 mol m-2 s-1 in the coarse and fine tailings, respectively. Pyrrhotite oxidation rates, as an alternative, were 2.31 + 10-12 and 1.24 + 10-11 mol m-2 s-1 in the coarse and fine tailings, respectively. Natural microbial activity was confirmed in both the tailings and the leachates; therefore, the obtained oxidation rates are not strictly abiotic. It is thus concluded, based on the experimental results, that tailing heterogeneity will result in zones with different oxidation rates, related to their physical and chemical properties.

Jan 1, 2003

By M McCurd, M Lynch, B H. Yin, S Mendoza, C W. Bumby, Y Iwasaki, B Rumsey

Iron and steel production is responsible for approximately 6.3 per cent of global anthropogenic CO2 emissions. Direct reduction of iron with hydrogen is a potential route for decarbonising the iron and steel industry. Extensive small-scale laboratory experiments have been performed to test the feasibility of hydrogen-direct reduction of iron ores sourced from diverse geographical locations. However, test results from the batch reduction of small-sample do not necessarily translate to continuous commercial-scale processes. Establishing a small-scale continuous test reactor for H2- DRI process is challenging, requiring substantial resources and investment. The limited availability of small-scale reactors that enable testing under relevant conditions has become a major obstacle for H2-DRI development, leaving a big gap between laboratory success and proof of commercial feasibility. Here, we report on the recent commissioning of a continuous counter-flow vertical shaft reactor, which has a processing capacity of 6 kg/hr iron ore pellets at up to 100 NL/min H2 flow. We believe this to currently be the largest H2-DRI facility in the Southern Hemisphere. In this talk, we will discuss the design and construction journey for this reactor, starting from the initial system design to the initial demonstration of H2 reduction of titanomagnetite ironsand pellets. This reactor now enables a range of research capacities, including the validation of laboratory results on a larger scale with practical operational variables, feasibility assessment of hydrogen direct reduction of different iron ores on a commercial scale; identification of scalability, sticking, and other potential issues before building a full-scale plant; and a viable solution for producing small-quantity DRIs for downstream melting investigations. Overall, this new research facility offers significant benefits for assisting the transformation of iron and steel production to a more sustainable and green industry.

Sep 18, 2023

By A M. van Niekerk, W Mey

Coal mining has an impact on the water management of the water scarce Upper Olifants River Catchment. A prefeasibility study was carried out by Anglo Coal and Ingwe Collieries Limited to establish the water supply and demand in the catchment. A geohydrological model was used for the coalfields to determine the stored water and excess water available. Two distinct collective and treatment systems were proposed for the Witbank and Middelburg municipalities to treat excess water from the Anglo Coal and Ingwe Collieries Limited. The Emalahleni Water Reclamation Project for Witbank was initiated first. Water management and treatment experience gained at Anglo Coal was the cornerstone to develop the collection, treatment and distribution system. A full enquiry was issued to Keyplan, Veolia, Bateman Africa and IST Technik to construct, commission, operate and maintain a 20 ML/day desalination plant to treat acidic, saline mine waters to a South African National Standard (SANS) 0241 Class 0 potable water. After the technical and financial adjudication, Keyplan were awarded the contract. An integrated regulatory process was adopted through consultation with all the relevant regional and head office staff of the Department of Minerals and Energy, Department of Water Affairs and Forestry and the Mpumalanga Department of Land Affairs via an authorityÆs steering committee. A rock engineering evaluation was done to select both the plant and waste disposal sites as all possible sites are undermined. Various contracts are required with the individual mines for water supply, the Emalahleni Local Municipality for the delivery of potable water and for the disposal of wastes.

Jan 1, 2006