Search Documents

The Mt Whaleback open cut mine South Wall is, in part, developed as an unbenched dip slope. The remainder of the rock slope consists of asymetrical overturned folds which have been locally truncated by major low angle faults. The Mt Whaleback orebody is structurally controlled and therefore extensive structural geology input has gone into the final rock slope design. The design is based on normalised 40 m geological cross sections, but the inherent complexity of the geological structure of the orebody yields a high degree of uncertainty within that interval. There- fore, the final slope bench face and the penultimate bench faces are mapped in detail to accurately establish the geological contacts and struc- ture. The knowledge of accurate geology of final and penultimate faces plays a very important role in the design of controlled perimeter blast- ing. Accurate geology is established mainly by face mapping, and by hole geological evaluation of blastholes to locally refine the current Geologi- cal model.

Jan 1, 1989

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By D Kent, J Bullock, M Wilkinson

Over the last few years at Glencore’s Mount Isa Copper Operations (MICO) mining conditions have become increasingly challenging through lower head grades and higher work indices. MICO has had great success improving operating efficiencies and increasing productivity through focusing on technology, innovation and operational discipline. The recent implementation of the Mine Site Technologies (MST) ImPact System has supported the continued transformation of the MICO operations through improved personnel safety and direct measurement of productivity. The ImPact System has implemented new safety systems such as the heavy vehicle proximity detection system, underground personnel tracking system and emergency evacuation dashboards improving the overall safety of the workforce. The ImPact System has facilitated productivity improvements via real-time equipment and personnel monitoring, and the implementation of exception reporting (personnel productivity), KPI reports and production dashboards, and transparent reports highlighting developing maintenance issues.This paper discusses the components of the ImPact System, the current installation at MICO, and critically analyses the implementation processes and right sizing of the system to meet the needs of the business today and into the future.CITATION:Bullock, J, Kent, D and Wilkinson, M, 2017. Productivity and safety improvements supported by MST’s ImPact System at Glencore’s Mount Isa Copper Operations, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 279–286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Hendon G. W, Carr F, Jiang Y

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By E Jak, G Khartcyzov, M Shevchenko

The increasing complexity of ore resources and recycled materials in the feed of pyrometallurgical processes present a technical challenge to the metallurgical engineers working on maximising the recovery of the valuable elements and minimising the environmental impact of the processes. To address this challenge, the availability of computational tools that can predict the mass and energy balance in complex systems is required. Then the accurate description of phase equilibria in the complex multicomponent systems describing the chemistry of the pyrometallurgical processes becomes critical for the correct implementation of the indicated tools and facing the outlined industrial challenges. In the present study the distribution of selected elements (Pb, Zn, Fe, As, Sn, Sb, Bi and Ni) between oxide liquid and metal in the ‘CuO0.5’-CaO-AlO1.5 system in equilibrium with Cu metal at 1400°C (liquidus of CaAl2O4) was experimentally studied using the equilibration and quenching technique followed by the electron probe X-ray microanalysis of the resulted samples. The study covered a wide range of effective p(O2) over the system from 10-11 to 10-3.5 (corresponding to formation of immiscible CuO0.5-rich slag). To avoid loss of volatile elements (Pb, Zn, As, Sn, Sb and Bi), a correlation between ‘CuO0.5’ in oxide liquid and p(O2) in open system was obtained first, followed by studying the volatile elements distribution in closed conditions (Al2O3 crucible sealed in SiO2 ampoule), where ‘CuO0.5’ concentration was used as a marker to evaluate the effective p(O2) over the system. The experimental results were then used for the optimisation of the thermodynamic model parameters of the system as part of the integrated experimental and self-consisting thermodynamic modelling research program of phase equilibria in the Cu-Pb-Zn-Fe-Ca-Si-Al-Mg-O-S-(As, Sn, Sb, Bi, Ag, Au, Ni, Cr, Co and Na) gas/oxide liquid/matte/speiss/metal/solids system.

Jun 19, 2024

By F T. Suorineni

Empirical methods are deeply rooted in geomechanics. This is a consequence of the recognised complexity of the nature of the rock mass. The usual assumptions of material continuity, homogeneity, isotropicity and linear elasticity often assumed for soil, concrete and steel are difficult to justify in a rock mass except for mathematical convenience. These assumptions form the bases for most mechanistic, analytical and numerical methods in geomechanics. Believers in empirical methods argue that the complexity of the rock mass and its interaction with structures developed in it is adequately accounted for in empirical methods, which compensate for our ignorance.Franklin (1993) defines empirical design as quantified judgement based on experience. He further states that empirical methods often prove ‘closer’ to the ‘truth’ than the apparently more precise predictions of theoretical analysis, adding that based on real data empirical methods provide a standard against which theoretical predictions are measured and can be judged. This paper takes a critical look at the common empirical methods in geomechanics – rock mass classification systems (Bieniawski, 1973; Barton, Lien and Lunde, 1974; Hoek, 1994a), Laubscher block caving design rules (Laubscher, 1994), the stability graph (Mathews et al, 1981), pillar design equations (Salamon and Munro, 1967; Hedley and Grant, 1972; and their derivatives), pillar design chart (Lunder and Pakalnis, 1997) and failure criteria (Hoek and Brown, 1980; and its derivatives). The common thread in the application of these methods is that in most cases they are often applied blindly without an understanding of the underlying assumptions and database limits. This paper emphasises that users of these methods need to know the underlying assumptions, database limits and inherent hidden risks that are often unmentionable for their satisfactory use. Finally, suggestions are provided for the efficient use of empirical methods and how they can be improved.CITATION:Suorineni, F T, 2014. Reflections on empirical methods in geomechanics – the unmentionables and hidden risks, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 143–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By B R. Castley

Consumable materials used in mines are often transported to the working areas down shallow angle decline shafts, typically at anywhere between 10¦ and 30¦ to the horizontal. The winding equipment is usually a relatively small single-drum winder and the material is transported in one or more cars, running on rails in the decline. The winding rope is attached directly to the cars, which are mechanically coupled together. For small rock hoisting declines, the cars are replaced with hoppers or skips. The winder is normally of basic design, fitted with only the minimum required safety devices and very elementary brake control. Since these winders are not ælicensedÆ and are usually located in remote areas, the standard of maintenance on the installations is often poor, leading to frequent accidents, resulting in runaways, derailments and broken ropes. These problems can be overcome easily with the application of the rope haulage principle. When large volumes of ore have to be transported to surface, belt conveyors are used on shallow angle inclines, or high-capacity friction winders are used in vertical shafts. Conveyors are limited to inclines no steeper than 14¦ and vertical shafts with large friction or drum type winders are extremely capital-intensive. Rope haulage systems can be used on decline shafts where the inclination is too steep for belt conveyors and too shallow for conventional drum winders. Rope haulage systems also offer a variety of safety, technical and cost advantages over other winding and transport systems. This paper describes the adaptation of the rope haulage principle to modern requirements and, combined with 21st century electronic technology, explains how the principle can be used as an efficient, safe and practical solution to some problems associated with the transport of materials, personnel and ore in mines. The authors describe the designs, methods of operation, safety aspects, automated control, loading and unloading facilities of modern rope haulage systems used for transporting personnel, material and ore. This paper considers a variety of systems already designed for different applications, from small material-only installations to multi-purpose and large rock-hoisting systems with payloads as much as 180 t. It also describes in more detail, a material transporting system recently commissioned in South Africa.

Jan 1, 2005

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By L Lachance, F Flament, D Leroux, S Gariépy

The pervasiveness of poor sampling practices in and around mineral processing plants could seem intriguing in view of the various documented evidences both for causes and consequences. To this extent, this paper revisits the well-documented but lesser-known fact that failure to care sufficiently about how samples are selected and managed is the mother source of almost all sampling biases. The authors believe that the potentially huge leverage between causes and consequences as well as the diversity of people involved in sampling call for a globally integrated solution rather than for a point solution. Such a globally integrated solution has already been put forward by the AMIRA P754 Metal accounting – code of practice and guidelines (AMIRA, 2007) that inherently requires accuracy to be targeted, measured, reported and managed. Furthermore, always in order to avoid a point solution, several layers of protection against biases must be put in place with each one involving a different ownership whenever possible. This is exactly the role intended by the supervisory bias detection method described in this publication. It is based on the continuous monitoring of the expected value of reduced residuals obtained from statistical data reconciliation conducted in a metal accounting context. This supervisory bias detection method is developed in full details after which Monte Carlo simulations are done on a mineral processing plant example for showing how it can be successfully applied for detecting hidden biases.CITATION:Lachance, L, Leroux, D, Gariépy, S and Flament, F, 2014. Detecting sampling biases in metal accounting, in Proceedings Sampling 2014 , pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By E Widzyk-Capehart, P Vallejos, R Asenjo, J Ruiz-del-Solar

Throughout the minerals industry, it is evident that a new wave of technological innovation is needed as the mining sector looks for ways to achieve higher security and safety as well as higher production rates with less investment. Innovation has always been one of the key factors in achieving success within the mining industry. However, its importance will be especially relevant in the coming years if negative trends in commodity prices and new challenges facing the industry (lower grades, deeper mines and economy of scales) are to be overcome and the future sustainability and profitability of the sector ensured.The drive towards fully autonomous operations has begun, with the implementation of automated systems in both surface and underground operations. However, these automated systems are currently planned and realised with well-defined automated tasks within structured environments and isolated spaces. Currently, there is no interaction between automated systems, manned systems or humans, which creates physically isolated environments.For fully autonomous and continuous operations, the automated systems need to operate in environments that enable flexible interactions between automated machines, tele- and manually operated machines and humans.In this paper, we address the automation paradigm considering the synergistic collaboration between humans and automated systems. In this paradigm, humans and machines would interact in a flexible, collaborative and synergistic way without the need for isolation. The implementation of this concept within mining operations will have to be underpinned by science and technological developments and will require adaptation from many fields, including robotics, automation, distributed systems, communication, human factors, pattern recognition and mine design.The paper also presents the research and development work being undertaken at the University of Chile’s Advanced Mining Technology Center, in collaboration with the Chilean mining industry. This will provide the basis for flexible interactions between humans and technology-based systems towards a future of autonomous and continuous mining systems.CITATION:Ruiz-del-Solar, J, Widzyk-Capehart, E, Vallejos, P and Asenjo, R, 2015. Synergistic collaboration of humans and automated systems – innovative steps towards fully autonomous and continuous mining systems, in Proceedings Third International Future Mining Conference, pp 83–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

In October 2005 Phelps Dodge mining, a US based company, visited several Australian mining companies and mine sites to ascertain the current applications of risk management methods in the organisation. The results of this review, documented by the author, indicated a ælayeredÆ approach from high level site or major hazard analysis through to face level, æstop and lookÆ, methods. The approaches of several companies were summarised in one simple layered model. This model is helpful to other sites and companies to identify potential improvements but also offers an image of best practice that may assist with the governance of OH&S by both company boards and community regulators. The issue is particularly relevant as we discuss national consistency in mining regulation. This paper examines the layered model, the company and site approaches that helped define the model, as well as the suggested implications of the layered model to governance.

Jan 1, 2006

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

Stope filling practice on the Great Boulder Mine was described in -a paper published in Aus.I.M.M., Proceedings No. 137, in 1945. When the paper was presented the process had emerged from the experimental stage, most of the initial operating difficulties had been overcome, and it had been established that this method of filling was suitable for the working of ore bodies in the Kalgoorlie field: Since 1945, it has fulfilled its early promise, -and during 1947, the tonnage of fill placed was sufficient to cover current operating requirements as called for by the mine ore breaking programme. The object of this paper is to outline current operations. In so doing it will refer' to some ground covered by the previous paper, but will omit details of the initial experimental work. It will include, however, a description of further experimental work on the use of hydraulic filling for worked-out shrinkage stopes, arid will provide more accurate data on costs than were available previously.ESTIMATE OF TONNAGE OF FILL REQUIRED.Early in 1946, the mine ore reserves were analysed in order to estimate the relative tonnages to be mined per four-weekly period by shrinkage stope methods -and by cut and fill stope methods respectively. This analysis was extended beyond the blocks already prepared for stoping, and inclqded the majority of the major ore blocks in the mine ore reserves. It gave the following results:-For a mill tonnage of 28,000 tons per period, 6,933 tons were required from cut and fill stopes, and a possible future maximum programme of 35,000 tons per period would require...

Jan 1, 1948

By J F. Colinet, G, J A. Zimmer, R J. Timko

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/non-metal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 per cent throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurisation systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a workerÆs clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2005

By O Handayani, R Barr, E Isaaks

The mining industry has focused a great deal of attention recently on the impact of blast movement on grade control. Although the problem of blast movement and its contribution to dilution and ore loss is well known, solutions to the problem are less than satisfactory. Perhaps the most recent innovation is the application of blast movement monitoring (BMM) devices to quantify blast movement. These devices emit an electronic signal and are planted at surveyed locations within the preblast material. Following the blast, their new locations are found using an electronic scanner. The magnitude and direction of the blast movement is given by the vectors between the pre- and post-blast BMM locations. However, it’s not clear how the BMM vector data can be best used to minimise dilution and ore loss. One common solution is to displace preblast dig line polygons by distances indicated by the BMM vectors. However, studies of BMM vectors show that blast movement not only displaces material laterally but also mixes material internally within the bench (Thornton, 2009a).This paper presents a method for modelling the post-blast muck pile that accounts for displacement and internal dilution using simulated annealing. The preblast ore control block model is re-blocked to 1?×?1?×?1?m sub-blocks. Each sub-block is displaced by simulated BMM vectors conditional to post-blast surface topography and blast initiation sequence data in addition to BMM vector data. The displaced sub-blocks are aggregated into new ore control model blocks whose grades are calculated from the contained sub-blocks. New dig lines are then designed on the post-blast muck pile model using the new ore control block model grades. A case study based on actual data is provided.CITATION:Isaaks, E, Barr, R and Handayani, O, 2014. Modelling blast movement for grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Excavator output rates given in Makers' catalogues are sometimes based on favourable operating conditions. Mine operators and planners are more interested in the Effective Hourly Output in normal operation (Qe) a plant system can give hour by hour and year after year in a particular application. The number of hours mining plant will be available for normal operation will be less than the annual total of 8760 h. The number of the available hours which can be utilised at Qe will depend largely on the number and types of units in the plant system, the manners in which they are applied and the nature of the deposit in which they work. The emphasis herein is on continuous systems for deep stripping with BWE's as the primary excavator. Examples and suggestions are given for the annual hours at Qe for some BWE systems.

Jan 1, 1981

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980

By A P. Wibowo

Indonesia holds a significant role in the utilisation of coal resources in the world. Although the number of Indonesian coal resources and reserves do not fall into the world’s top ten, according to 2009 statistics, Indonesia is the seventh largest producer of coal with a production of 256 Mt. More than 80 per cent of this amount is sold in the export market, making Indonesia the world’s second largest coal exporter. Most of the exported coal from Indonesia is used to fulfil the needs of the Pacific market, such as Japan, Taiwan, China, among others. It is also possible to reach the Atlantic market.Along with Indonesia’s development program, until 2025 the Indonesian government has adopted a National Energy Policy that aims to reduce the role of petroleum in electricity generation and replacing it with coal. As a follow-up of the policy, since 2009 PT PLN, the state electricity company has built steam power plants throughout Indonesia as an implementation of the first stage of the Electrical Acceleration Project with a capacity of 10 000 MW. Moving forward, in 2011 PT PLN will also build the second stage of the project with a capacity of 10 000 MW. As a result of the program, the domestic need for coal is expected to increase as much as 44.8 Mt.With the increase in domestic need and decrease in the number of reserves, the Indonesian government has adopted policies to secure the domestic coal supply. A policy that may potentially be adopted by the government is the limiting of coal production, seeing the high rate of increase in Indonesian coal production. The adoption of such a policy will change the distribution map of coal in the Pacific market. Thus, this paper will evaluate the change of coal distribution patterns in the Pacific market along with the increase in Indonesian domestic needs and Indonesian adoption of policies regarding the securing of coal supplies.

Nov 22, 2011