Search Documents

By N Dube, K L. Sandvik, C Mutevhe

Trojan Nickel Mine is the largest producer of Ni, Cu and Co in Zimbabwe. The mine has operated a nickel flotation concentrator and base metal refinery continuously since 1969, creating 28 million tonnes of sulfide bearing tailings, five million tonnes of permanent waste rock and about seven million tonnes of smelter slag. Exposure of the sulfide bearing minerals renders them susceptible to oxidation in the presence of water and oxygen, resulting in acidic solutions with elevated concentrations of total dissolved solids, sulfate, metals and residual flotation chemicals in various waters draining from the mine site. These pollutants pose a direct threat to the environment and human health, and understanding their deportment and behaviour in the various waste streams is essential in the mineÆs environmental objectives to prevent or minimise adverse impacts arising from its operations. A geochemical assessment of the pollutants was carried out to compute a mass balance between the major sources of pollution and the distribution and fate of pollutants in waste streams from the mine site. Waste rock, tailings, surface water, ground water and sediments were sampled, tested and analysed. Mineral composition and water chemistry data show that geochemical reactions are responsible for the release of pollutants from waste rock, tailings and plant spills. Drainage from the mine area is near neutral due to buffering by magnesium carbonates in the fine fraction of the tailings. The natural wetlands that exist downstream of the waste rock and tailings dams are effective in reducing metal loadings to water courses. However, solutes and heavy metals are occasionally released to surface and ground water, when their concentrations peak during the dry season. The results demonstrate the necessity to understand the natural chemical processes that characterise the distribution of pollutants in nature and how such knowledge can be used to develop cost effective methods to remediate pollution in the natural environment.

Jan 1, 2006

By U Singh

This paper presents the evolution of the studies and strategic plans to extend the life of operations at the Savage River iron ore project in north-western Tasmania. The current Life-of-Mine (LOM) plan for the Savage River operations is based on a series of open pits. Drilling has confirmed high-grade extensions of the magnetite resource at depths that exceed practical limits for open pit mining. Grange Resources Limited, the owner of the operation, is investigating underground options – not only to extend the LOM plan but also to maintain peak production at a reduced operating cost while reducing greenhouse gas emissions into the future. What makes this project unique is that it requires introducing a productive and cost-effective mining method to exploit a challenging geotechnical and geometrical orebody in an area of high rainfall. To support the study efforts, the development of an exploration decline, underground drilling programs, and an exploratory drive excavated into the orebody for geotechnical investigation was key to providing the necessary data for a pre-feasibility study (PFS). This paper describes the pragmatic approach and processes to developing the underground mining options study through data collection and then integrating these options into the open pit plans to optimise an overall strategic plan for the Savage River operations. The learnings for operators from this experience are how the technical and pragmatic approaches were aligned to develop the strategic plans, and the importance of timely investment in gathering the necessary data.

Mar 29, 2023

By B Belle, M Biffi

Cooling of coal mines in the Bowen Basin, characterised by steep geothermal gradient, is presently achieved mostly through rental surface bulk air cooling in summer months. This paper argues that future mines will be required to focus their cooling resources more intensively to manage a challenging thermal environment where virgin coal temperatures of over 50¦C at a depth of 500 m are expected. Currently, mine cooling systems are employed to maintain the wet bulb temperatures (WBT) to below 27¦C at which point the risks of heat stroke or other heat-related issues are manageable. The capacities of these systems are in the range of 6 MWR to 10 MWR. The relationship between high working temperature environments and injury frequency rates is well established. Therefore, provision of appropriate cooling strategies and understanding their optimum performance and suitability are important to Australian coal mines of the future. This paper evaluates the underground temperature profiles of deep, gassy coal mines with propensity for spontaneous combustion and proposes the long-term cooling pathways to effectively manage thermal hazards. Thermodynamic modelling is performed on a longwall face and includes air leakage effects from goaf streams at various locations along the longwall face. The strategy summarises the application of underground bulk air cooling, chilled water sprays on the shearer and the resulting temperature profiles. Considering the new mining projects planned for the Bowen Basin region, a review of implementable cooling strategies such as mid-gate mobile bulk air coolers (BACs), spot coolers, underground bulk air cooling and the use of chilled water to enhance the positional efficiency of cooling plants, are discussed in this paper. Finally, the comparison of ærentalÆ versus æownershipÆ of cooling plants is analysed as part of long-term cooling strategies.CITATION:Belle, B and Biffi, M, 2013. Cooling pathways for deep Australian longwall coal mines of the future, in Proceedings The Australian Mine Ventilation Conference , pp 223-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Dennis, T Hunter, R Coleman

For metallurgical plant design, it is necessary to progress through successive phases of test work, piloting and process development before involving all the other engineering disciplines and “freezing” the process design criteria and flow sheet. This process usually relies upon the experience, skills and personal preferences of various technology providers, study and engineering entities, test work and metallurgical laboratories and, most importantly, the owner’s team and its operators. Current industry trends include lower grades, more complex orebodies, geometallurgy in defining orebody variation and design envelopes, more common “hybrid” plant processes and the market demands for more reliable, timely and predictable early plant performance.This paper will discuss interaction of these trends and provide guidelines for the level of detail and technical complexity required for a number of different “typical” examples. The paper will pay particular attention to the study definition level translated into the required detail and certainty needed by the overall process “owner” and original equipment manufacturer (OEM) equipment suppliers to ensure the best real plant performance. Some recent case studies will be discussed. In many projects, at a late stage of project definition, it has become common practice to undertake a “value engineering” phase. Although it could be argued that this should be undertaken earlier, it is largely driven by an overall need to reduce capex and “optimise” the perceived “fat” built into the project during the detailed design process. This value engineering can be very counterproductive to project timing and operational performance and warrants discussion.The paper is intended to promote discussion on a topic of wide interest. The authors’ diverse backgrounds and experiences are integral to the views in this paper.CITATION:Dennis, A, Coleman, R and Hunter, T, 2017. Critical process design considerations from test work to operations, in Proceedings MetPlant 2017, pp 12–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

A series of petrological studies were carried out on the characteristics of alteration and mineralisation in mainly structural-controlled (Deep Star, Meikle, Deep Post) and predominantly lithological-controlled (Post-Betze-Screamer and West Leeville) gold deposits in the northern district of the Carlin trend, Nevada. Alteration and mineralisation in these deposits are hosted in a sequence of calcareous clastic units of the Devonian Popovich Formation, into which have been emplaced a number of Jurassic intrusions, and syn- to post-mineral Eocene dikes. Four hydrothermal events have been recognised in these deposits: an initial Devonian base metal system and early diagenesis; a Mississippian stage of alteration in conjunction with burial metamorphism; contact and hydrothermal alteration and base metal-gold mineralisation associated with the emplacement of the Jurassic intrusions; and a Carlin-style gold system related to Eocene magmatism.

Jan 1, 2004

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S G. Li

Mine intelligent ventilation is an important guarantee to realise intelligent mining. It is the integration of the Internet of Things, big data, artificial intelligence, internet, cloud computing with ventilation technology, forming a complete ventilation system with intelligent perception, intelligent decisionmaking, intelligent emergency response and airflow control. In order to fully grasp the progress and trends of mine intelligent ventilation research in western China. The paper based on literature analysis and field application research, comprehensively expounds the main research and practical results of mine intelligent ventilation in western China, mainly analyses the development status of key technologies such as accurate and rapid determination of mine ventilation parameters, intelligent analysis and decision-making of ventilation and intelligent regulation of ventilation equipment, and introduces the field test or application of mine intelligent ventilation technology in western China. It lays the foundation reference for related research and improving the intelligent level of mine ventilation.

Oct 12, 2022

By A Roseman, T Gruber

Traditional methods for installing gaskets for segmented bored tunnels have relied upon different bonding procedures with adhesives that carry a series of disadvantages to segment producers. Fixation of the gaskets into the concrete segment as part of the casting procedure has been developed over the last 20 years and has emerged as an economical solution to produce high-quality tunnel segments for various technical tunnel applications. This paper investigates the advantages of using anchored gaskets, the different tunnel systems that employ anchor gaskets and reviews the first anchor gasket project; the Lee Tunnel and analyses how segment production efficiencies are gained.CITATION:Gruber, T and Roseman, A, 2014. Use of anchored gaskets in segmented bored tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 253–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Benn, V Kuznetsov, G Timms, A Spain

Earthen covers are now widely used in the mining industry to control the generation rate and/or release rate of low quality drainage from piles of sulfidic minewastes. Covers are usually designed to reduce the water infiltration rate and in some cases may also reduce the oxygen flux to the underlying sulfides. Engineered covers have only been used since the 1980s, however, and there is very little field data on their performance in the longer term. This lack of information has implications for the degree of confidence that can be placed on the predictions of the environmental impacts of sulfidic minewastes, for the acceptance of close-out criteria by regulatory authorities and for the financial liability of the mining industry. Covers were placed on sulfidic waste rock dumps at the abandoned Rum Jungle uranium mine during 1984 - 1985. These covers were designed to reduce the water infiltration to less than five per cent of incident rainfall by both water shedding and storage-release mechanisms. Regular monitoring by the Australian Nuclear Science and Technology Organisation (ANSTO) demonstrated that the covers performed better than the design criterion for around ten years, but infiltration rates have subsequently increased. There is a 66 per cent probability that the infiltration rate now exceeds five per cent of incident rainfall. The cover on the largest pile, WhiteÆs heap, was sampled in pits dug at eight locations. Sampling was carried out at the end of the monsoonal wet season and again at the end of the ædryÆ season. This, together with laboratory testing, enabled cover performance to be assessed against five criteria: design, construction, cover material characteristics, physico-chemical characteristics and biological characteristics. We are of the opinion that the design of the cover was suitable to achieve the objectives of stability, water shedding, storage-release, and provision of a substrate for vegetation growth. Over most of the surface of the heap, the construction of the covers, drains and erosion prevention structures was in accordance with design specifications. However, several small and localised bare patches on the upper surface of WhiteÆs heap coincide with a reduced cover thickness, which is likely to have been due to poor construction in those patches. The construction of covers on minewastes is dependent on an adequate source of material meeting design specifications. From our limited examination, it appears that there was shortage of material for each of the three zones û a lower impervious clay layer, the moisture storage-release layer and the upper erosion-resistant layer for vegetative growth. An indication of this was that the upper layers in some areas were observed to be thinner than specified. We are of the opinion that this shortage of suitable material has been responsible for some of the changes observed ten years after emplacement. Physical and geotechnical testing indicated that the cover materials no longer meet the original specifications. In particular, the permeability at the 8 locations was found to be greater than specified, by up to several orders of magnitude. The higher permeability may explain the higher observed rainfall infiltration and moisture content of the waste rock. This increased permeability appears to be due to a combination of biological and physical processes û galleries formed by termites and ants and an extensive system of shrinkage/desiccation cracks formed by the development of a polygonal blocky structure involving the entire lower clay layer. The desiccation cracks may fill with coarser illuviated materials and form a conduit through which roots access the underlying waste rock. Measurements were made of oxygen flux into the heap as cover layers were excavated in the pits. They indicated that the full cover currently reduces the oxygen flux to 20 - 23 per cent of that into bare waste and that this reduction seems to be proportional to the cover thickness. It was also found that the oxygen flux into the cover is about four times higher at the end of the dry season than at the end of the wet season and that the difference is due primarily to the difference in moisture content of the cover. Recommendations are made for the design and construction of covers.

Jan 1, 2003

By M Gasparon, J Harris, T Baumgartl, D J. Williams, M Edraki, P A. Kirsch, D Rowe

RISKGATE, an Australian Coal Association Research Program-funded (ACARP) initiative, has been designed to assist the Australian coal mining industry in improving minimum standards for safety performance, efficiency, operating practice and training. The online system is innovative in that it is built upon a foundation of industry expert knowledge gathered through action research workshops, which is further supported by a broad array of industry, academic and technical resources. In operation, RISKGATE offers a continuum for knowledge transfer and communication of current practice in risk identification, assessment and management in the coal mining industry. The primary mission of RISKGATE is to focus industry attention on prioritising control management as a way to achieve acceptable risk.A Coal Mine Tailings Dam Module has recently been added to the RISKGATE suite. The key risk, or initiating event, associated with coalmine tailings dams is catastrophic failure of the dam, leading to the release of tailings and water. This can occur due to geotechnical instability of the dam itself or of its foundation, overtopping and erosion of the dam, and piping failure of the dam itself or of its foundation. Coalmine tailings dams are also prone to seepage into the foundation and through the dam, particularly during operation when large volumes of water are discharged with the tailings. The most significant risk associated with seepage is the release of potentially contaminated water to the environment. Contamination can take the form of elevated salinity, acidity and dissolved metals. Run-off from coalmine tailings can cause erosion and can also potentially contain contaminants. Desiccation of the tailings surface can result in dust generation and dispersion.The paper presents the background and context of the RISKGATE project, the need for the addition of the RISKGATE Coal Mine Tailings Dam Module, and a description of the developed module, including the five initiating events considered, their causes and associated preventive controls, and their consequences and associated mitigating controls. This paper concludes with a discussion of the ways in which Australia’s coal mining companies are starting to apply the RISKGATE body of knowledge at their sites, which will flow onto the management of their tailings dams.CITATION:Williams, D J, Kirsch, P A, Gasparon, M, Baumgartl, T, Edraki, M, Rowe, D and Harris, J, ?2014. Application of RISKGATE to coal mine tailings dams, in Proceedings Life-of-Mine 2014 , pp 219–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J Ta’ala, M Handyside

Mechanical sampling from conveyors has historically been a staple in the iron ore industry when information related to chemistry, sizing and moisture is required. In order to comply with ISO 3082:2009, samples can be taken either on a mass or time basis provided no bias is introduced by periodical variation in quality or quantity. With the introduction of mechanical sample carousels, you also have the opportunity to collect samples on a mass or time basis. In order to optimise automatic sample stations in a changing production environment, BHP Billiton Iron Ore (BHPBIO) has developed a simulation model that enables the various combinations of mass–mass, mass–time, time–time and time–mass to be investigated.The sample station model can utilise actual (variable) feed rates to achieve high resolution and enables the simulation of sample size variation. Cutter speeds and other settings can then be adjusted to better optimise the performance of the sample station with regards to optimal sample size as well as ensuring the sample station is in compliance with ISO 3082. The model can also assist process engineers in adjusting settings to better optimise the sample station and reduce unwanted events such as blockages. The model can be easily modified to conform to various sample station designs. This paper demonstrates the use of the model and the benefits that can be achieved.CITATION:Handyside, M and Ta’ala, J, 2014. Simulating time versus mass basis?sampling, in Proceedings Sampling 2014 , pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Taylor G. H

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopical techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relat- ing their inherent properties to properties such as volatile- matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used coimierciallyti,

Jan 1, 1969

By J Butler, N Patel, S Narendranathan, S Rastogi

The Yallourn Mine (YM) commenced mining of brown coal in the 1920s under operation by the State Electricity Commission of Victoria (SECV), prior to it becoming privatised in 1996. The present owners of the YM, Energy Australia Yallourn (EAY), acquired the site in 2000 and intend to continue operations until scheduled closure in 2028. Brown coal extracted from the YM is fed into the Yallourn Power Station which supplies approximately 22 per cent of Victoria’s electricity. Water within the YM is collected and stored in the Township Field Fire Service Pond. Water levels within the Fire Service Pond (FSP) may fluctuate considerably depending on the requirement for storage at the site. With due consideration to the stability performance of mine batters adjoining the FSP, the authors performed slope stability assessments to evaluate the risk and consequence of batter instability during the potential pond filling as it approaches the ‘critical pool’. The critical pond is defined as the level at which the driving forces (destabilising forces) are at their greatest and the resisting forces (lake forces, friction) are at their lowest. This assessment was undertaken using the Mine Geotechnical Risk Index (MGRI) approach.

Aug 2, 2023

By W R. Adamson

Cerro Vanguardia SA (CVSA), property of AngloGold Ashanti, mines gold and silver from a system of vetiforme orebodies located in the south of the Argentine Patagonia, in the Province of Santa Cruz.Surface mining techniques are applied to develop a series of narrow pits with an average waste to ore ratio of 26:1. This quite unique constraint brings into focus the need to maximise inter-ramp and final wall angles, leading to a strong need to optimise wall control drilling and blasting in order to reduce back-break damage to an absolute minimum.The paper describes a program of applied investigation and design modification implemented during?2008?and?2009 in?two?separate pits of Cerro Vanguardia. Three distinct yet complementary damage mechanisms were identified and observed during the field components of the work; vibration induced strain fracturing, surface cratering around blasthole collars and quasi-static loading and unloading of the surrounding rock mass as a consequence of poorly controlled confinement.With these mechanisms identified, a measurement, modelling and modification campaign was conducted in order to reduce the incidence of each source of damage. Interactive design analysis and modelling, near-field vibration measurement, video capture and the application of electronic initiation technology were supported by seed wave modelling and topographic evaluation of the achieved results.Results point to the usefulness of simulation techniques for determining optimum delay timing to reduce vibration impact, while the visualisation of explosive energy distribution produced by drilling and explosive loading decisions assists in reducing the probability of over-confinement.This paper presents relevant aspects of the two fieldwork campaigns:1) describing the application of the techniques, and2) summarising the results obtained.

Nov 8, 2011

By E J. B van Etten

Pit lakes may form when open cut mining leaves a pit void that then fills with ground and surface waters. This often replaces terrestrial ecosystems that existed prior to mining with an aquatic ecosystem, affording an opportunity to improve regional aquatic biodiversity values through targeted aquatic restoration (McCullough and van Etten, 2011). Restoration theory provides guidance when restoring disturbed systems towards landscapes that are of regional value and relevance. But how do we identify a restoration target for a novel aquatic habitat that only exists in the new post-mining landscape? This paper presents a process of first identifying and then surveying local representative aquatic systems, to provide a direction for pit lake restoration efforts and achievement criteria for pit lake relinquishment, using a case study from a sand mining operation amongst wetlands in south-western Australia.The company mines silica sands following mechanical removal of topsoil and then extraction of the ore from below the watertable by dredging. Assessment of wetland and riparian vegetation was achieved through the establishment and measurement of temporary monitoring transects across five natural wetlands in the Kemerton area. Several more regional wetlands were also visited and observations made to supplement and validate these data.Distinct vegetation zonation was found across each wetland, although typically wetland basins were unvegetated or filled with younger woody plants with patchy distributions. Fringing riparian vegetation consisted of few species (commonly the paperbark Melaleuca rhaphiophylla and the sedge Lepidosperma longitudinale), but community composition and structure were variable between wetlands. The pattern of vegetation seen across natural wetlands was best explained by topography and soil chemistry, with low lying wetland areas more likely to experience regular flooding and accumulate organic matter and nutrients.In conclusion, where they are available, regional natural waterbodies may constitute the best valid restoration goal. Nevertheless, the goal may need to consist of a range of closure design opportunities, rather than a single target.

Oct 5, 2011

By A B. Richards

A brick veneer house located on a open-pit coal mine lease has been subject to ground vibration levels of up to 222 mm/s, and air vibration levels of up to 145 dBL. The dynamic response of the structure was measured with accelerometers, geophones, and strain gauges as part of a project investigating the response of brick veneer houses to blasting. This paper outlines the project, and provides information on brickwork strength, foundation investigations, and observations on damage due to blasting. Correlations have been made between crack behaviour and factors such as blast vibration levels and rainfall.

Jan 1, 2001

By S J. Schafrik, Z Agioutantis, E C. Jong, K Luxbacher

Real-time monitoring of mine operating parameters is available at most mines. However, access to these data for an individual operation is typically underutilised by mine managers and technical personnel. Such monitoring systems are typically designed to provide data streams and alarms to a responsible person, but they are not utilised to extract underlying trends or correlate different data groups. Furthermore, multiple monitoring systems are usually implemented at a given site without interconnection between vendors’ systems or connection to any central management, and mine personnel are only exposed to a minimal subset of such data. Thus, it is not easy to analyse and correlate individual data streams and generate information to enhance day-to-day operational decision-making and improve safety and efficiency.This paper addresses the primary challenges associated with centralising data management and effecting greater utilisation of the vast amount of collected data, while at the same time reducing the time and effort required to manage such large data sets. Furthermore, it presents the conceptual design of a database application that can organise, present and analyse data collected by multiple sensors in different environments. The database is designed to operate in a passive manner so that active mine data management systems are not impacted. An example is given where this database is used for managing atmospheric data collected at an underground coalmine operation in the US. These techniques have a universal application and can be incorporated in a wide range of mining and construction projects.CITATION:Agioutantis, Z, Schafrik, S J, Jong, E C, Luxbacher, K and Karmis, M, 2015. A platform for managing and analysing atmospheric data in underground coalmines, in Proceedings Third International Future Mining Conference, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T BoBo, D La Rosa, P Cameron

Efficient pre-concentration using natural and induced deportment starts with effective blast design. Leveraging these characteristics using Size-Based Grade Engineering® techniques requires detailed understanding and measurement of the particle size distribution (PSD) of the Run of Mine (ROM) ore. In turn, blasts must be designed to optimise fragmentation for the pre-concentration method. To be successful, fragmentation outcomes must be predicted and measured as part of the blast design process to account for the response ranking of the rock mass. The upgrade achieved using Size-Based Grade Engineering® methodologies will rely on the proportion of feed that reports to the screen undersize, so particle size distribution of the feed stock is of paramount importance if the potential benefits are to be achieved and maintained. Measuring actual fragmentation in the ROM ore and comparing with predictions allows the modification of subsequent blast designs to optimise fragmentation for pre-concentration scenarios. Automating this process can deliver significant increases in productivity and mine site profits. This paper discusses the importance fragmentation plays in Size-Based Grade Engineering® and explores technologies and methodologies used to measure it, consistently ensuring the best outcomes.

Nov 10, 2020

By C te Kloot, Z Liu

Blast performance and the resulting drawpoint condition and volume of oversize has the potential to impact operator safety and mine productivity. Underground measurements showed that approximately 14 per cent of production rings in the Ernest Henry Mine (EHM) sublevel caving (SLC) operation had either overbreak in the brow or left collars. There were also oversize rocks reporting to approximately 30 per cent of drawpoints, which accounted for over 7 per cent of total production and significantly impacted production rates. A series of trials were conducted in 2015–2016 at EHM to test changes to certain charge parameters in an attempt to optimise blasting results and, in particular, reduce oversize and overbreak. The detailed analysis conducted included field observations, hole surveying, blast monitor analysis and blast modelling. There were a total of nine charge parameters tested in the project, which fell into two major categories: energy distribution and inter-hole delay. These were based on observations made in establishing baseline data and those parameters most likely to have a significant impact on overbreak and oversize.Key results from the project included oversize reduction and improved brow conditions when energy distribution was reduced through changing charge lengths in certain holes in the standard charge plan. Similar benefits were also seen when the inter-hole delay between blastholes was reduced from 50 ms to 25 ms. Based on these results both changes were made to the standard production ring charge plan at EHM.Moving forward, the aim is to continue monitoring the results from the changes made on all levels to ensure efficiencies are being realised and sustained. A 3 per cent improvement in oversize as a percentage of total tonnes and improved brow conditions not only has a positive impact on production rates, but removes people from any potentially hazardous situations and contributes to a safer working environment.CITATION:te Kloot, C and Liu, Z, 2017. The evolution of production blasts at Ernest Henry Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 33–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D R. Seaman, Y Peng, F Burns, D J. Bradshaw

Telfer Gold Mine is a gold-copper mine in the eastern Pilbara of Western Australia, owned and operated by Newcrest Mining Limited. TelferÆs ores are processed by a dual train, 21 Mt/a, concentrator where gold is primarily recovered by gravity concentration and the flotation of a gold-bearing copper concentrate. A minor portion of TelferÆs gold is also recovered to a pyrite concentrate that undergoes treatment via carbon-in-leach (CIL) cyanidation. The gold recovery of the CIL circuit is below the industry standard and operates with a high reagent consumption rate.With a new fine-grinding facility, the Telfer process plant will have the ability to liberate copper and gold from the pyrite concentrate and recover these by flotation prior to the existing leaching circuit. This process will improve overall gold and copper extraction, while reducing reagent consumption in the CIL circuit.This article is an overview of the development of this methodology. Size-by-size analysis and mineralogical studies of monthly composites identified factors limiting the CIL gold recovery and the causes of high reagent consumption. Laboratory studies confirmed a relationship between the regrind product size and gold leach recovery. The addition of an intermediate flotation stage ensured that the regrind circuit will improve overall recovery while at the same time reducing operating costs. Without the addition of a flotation stage, the additional reagent consumption from regrinding alone would be prohibitive towards increasing recovery. Pilot scale studies confirmed the conditions required to selectively recover gold and copper from the pyrite concentrate as well as establishing the full scale regrinding energy requirements. Construction of this facility at Telfer is currently underway.CITATION:Burns, F, Seaman, D R, Peng, Y and Bradshaw, D J, 2012. Development of a pyrite regrind circuit at Telfer Gold Mine, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 45-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012