Search Documents

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

By S. Ramachandran, N. J. Grant, T. B. King

MANY investigations of the rate of the sulfur transfer reaction between carbon-saturated iron and blast furnace type slags have been made." It is evident that the reaction is complex, the rate being affected by the presence of elements dissolved in the metal that are readily oxidized and therefore capable of existing in the slag phase. Thus Goldman, Derge, and Philbrook- have shown that carbon, silicon, manganese, and aluminum, in order of increasing effectiveness, accelerate sulfur transfer from iron containing these elements to blast furnace type slags. Quantitative information is still, however, not available on the relation between what have been termed side reactions, such as silicon transfer and CO evolution, and the sulfur transfer reaction itself. In other words, the stoichiometry of the reaction has not been investigated. In the present investigation, the transfer of all reacting elements and the evolution of CO have been measured simultaneously in order to establish the mechanism of the reaction which occurs in practice. Information of this nature cannot be deduced from equilibrium studies. It should be pointed out that in kinetic studies of this type quantitative conclusions are applicable only to the system studied. This restriction should be borne in mind when attempts are made to compare results from different investigations. Apparatus The apparatus used enables slag and metal samples to be taken at frequent intervals and also provides a continuous record of the amount of gas evolved. A sketch of the apparatus is given in Fig. 1. It may be considered in three sections: 1) furnace section, 2) blank volume section, and 3) pressure measuring section. The furnace section is shown in detail in Fig. 2. It consists of two graphite crucibles, C and D, super-

Jan 1, 1957

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

Organization Place Date 1919 American Society of Mechanical Engineers... New York, N. Y. Dec. 2-5 American Institute of Chemical Engineers.... Savannah, Ga. Dec. 3-6 Geological Society of America..: Boston, Mass. Dec. 29-31 American Society of Heating and Ventilating 1920 Engineers New York, N. Y. Jan. Mining and Metallurgical Society of America.. New York, N. Y. Jan. 13 American Institute of Min. and Met. Engineers New York, N. Y. Feb. 16-19 American Ceramic Society Philadelphia, Pa. Feb. 23-26 American Electrochemical Society Boston, Mass. Apr. 8-10* *On Apr. 9, a joint meeting will he held with the A. I. E. E.

Jan 12, 1919

[ ]

Jan 1, 1938

By Russell A. Carter

Alaska is a land of immense proportions and resources. Its very name, derived from an Aleut term, means "The Great Land." Yet, in a state slightly larger than Texas, California, and Montana combined, there are presently only two-large scale mines in production, excluding dredge operations. Once referred to by its territorial governor as "a storehouse of minerals," Alaska is, in the opinion of many industry observers, at least 20 years away from a healthy, productive mining industry. The mineral potential of the state is tremendous: coal deposits on the North Slope alone have been hypothetically pegged at 1.5 trillion tons. Copper-zinc deposits on the south flank of the Brooks Range are conservatively estimated to be worth $4 billion to $6 billion. However, the problems facing mineral development are of equal magnitude, and include:

Jan 11, 1976

By Jerome F. Kuzmick

Condusions. From the work on aluminum powder, the following general con clusions can bc drawn: I. The physical properties of aluminum compacts, such as density. strength and ductility, increase with increasing pressure, up to the practicable pressure limits. 2. Good properties ill aluminum con pacts can be secured only by the use of high pressures, because it is neccssary to rupture the refractory oxide film on aluminum powder. 3. Considerable softening of the specimens occurs upon sintering. regardlers of the pressure used. General Conclusions 1. For relatively short-time sintering. molding pressure is a very important factor in the final physical properties of the sintered specimens. 2. The effect of pressure. is difierent for each metal, so that few general rules can be drawn that would apply to all metals. 3. In many cases, fur a particular metal powder and sintering temperature there is a critical pressure at which the best physical properties can be obtained. 4. The principles of cold work and in nealing and their effect on grain structure applied to massive metal also holds true for sintered metals. 5. Particle size, at least for electrolytic iron powder, does not have a. great effect on ultimate grain six. DISCUSSION [E. E, Schumacher presiding V.. V. Crane. *—I was particularly impressed with Dr. Kuzmick's work on tin IF not the illustration, particularly the Second one. a very good illustraition of hot preessing. in that

Jan 1, 1945

Apr. 26-May 11, Liege International Fair, Liege, Belgium. May 4-8, Electrochemical Society, Inc., Spring meeting, Benjamin Franklin Hotel, Philadelphia. May 5-6, National Air Pollution Symposium, Huntington Hotel, Pasadena. May 5-7, American. Mining Congress, coal convention, Netherland Plaza Hotel, Cincinnati. May 6-9, Scientific Apparatus Makers Assn., annual meeting, Edgewater Beach Hotel, Chicago. May 9-10, AIME, joint meeting, Industrial Minerals Div. and Metals Branch, Davenport Hotel, Spokane, Wash. May 11-14, American Institute of Chemical Engineers, Atlanta Biltmore Hotel, Atlanta. May 17, AIME, Chicago Section, President's night dinner dance, Shoreland Hotel, Chicago. May 27, AIME, Morenci Subsection, Longfellow Inn, Morenci, Ariz. June 2-4, Chemical Institute of Canada, annual conference, Montreal. June 4-14, Mechanical Handling Exhibition and Convention, Olympia, London.

Jan 1, 1952

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

By Robert F. Mehl, Dana W. Smith

It has been shown that quenched iron of high purity exhibits a Wid-manstiitten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fc forms from y Fe in plates parallel to the (III), octahedral, planes in the y lattice. Because of this, and also beqause of the general similarity to the structural appearance of martensite and to the Widmanstatten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relationships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relationships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view. Experimental Technique The analysis of the crystallographic mechanism of transformation in pure metals is beset with special difficulties, though some information

Jan 1, 1934

By Elmer W. Pehrson

NINETEEN FORTY-SIX was an eventful year for the mineral industries. Perhaps the most significant development was the socialization of industry in Great Britain, initiated in 1945 but carried to fruition in the coal industry in 1946. On Jan. 1, 1947, management of the coal industry will be vested in a National Coal Board, responsible to the Ministry of Fuel and Power. A sum of £164,660,000 has been provided to compensate private owners for assets transferred to the Board. The British coal industry has been a problem for many years. Production has declined to a point where serious shortages of fuel for domestic needs have developed. Exports have dwindled to a small fraction of the previous trade. Costs have increased greatly, and quality has deteriorated. The industry's physical plant has not kept pace with the rapidly mounting wage scales in recent years. Some claim that the best and most accessible coal reserves of Britain are heavily depleted. The industry has been harassed by difficult labor problems, including bad morale among the workers and a shrinking labor force.

Jan 1, 1947

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy's law for fluid transport, can be written as:

Jan 1, 1967

CONTENTS PAGE BAIN, EDGAR C.-The Nature of Martensite. Discussed by Ancel St. John, Henry S. Rawdon, Jerome Alexander, Howard Scott 1 FEILD, ALEXANDER L.-Effect of Zirconium on Hot-rolling Properties of High-sulfur Steels and the Occurrence of Zirconium Sulfide. Discussed by Beram D. Saklatwalla, Bradley. Stoughton, Andrew M'Cance, George F. Comstock, Alexander L. Feild 12 SAUVEUR, ALBERT and KRIVOBOK, V. N.-Use of Sodium Picrate in Revealing Dendritic Segregation in Iron Alloys. Discussed by George F. Comstock, John H. Hall 17 KINNEY, C. L., JR.-Economic Significance of Metalloids in Basic Pig Iron in Basil Open-hearth Practice. Discussed by V. J. Pazzetti, George B. Waterhouse, C. L. Kinney, Jr 19 NEAD, J. H.-Absorption of Sulfur from Producer Gas in Open-hearth Furnaces.. Discussed by George B. Waterhouse, C. L. Kinney, Jr 26 PRIESTLY, WILLIAM J.-Effect on Steel of Variations in Rate of Cooling in Ingot Molds. Discussed by Emil Gathmann, Paul E. McKinney, George A. Dornin. 27 MONYPENNY, JOHN H. G.-Stainless Steel, with Particular Reference to the Milder Varieties (Stainless Iron). Discussed by P. A. E.-Armstrong, Beram D. Saklatwalla 33 ROYSTER, P. H., and JOSEPH, T. L.-Effect of Coke Combustibility on Stock Descent in Blast Furnaces. Discussed by Ralph H. Sweetser,. Richard Franchot, Sidney Cornell, T. L. Joseph 41 DAVIS, F. W., and BOLE, G. A.-Observations on Requirements of Refractories for Open Hearth. Discussed by C. L. Kinney, Jr., L. F. Reinartz, P. E. McKinney 46

Jan 5, 1924

By Joseph M. Locke

The discovery of this asphaltum was made by S. H. Gilson, of Salt Lake, and since then the material has borne the local name of Gilsonite. So far as I have been able to ascertain, however, the first published notice of this discovery was made by Prof. W. P. Blake in the Engineering arid Mining Journal, of December 26, 1885, where he names the new mineral Uintahite, from the place of its discovery, the Uintah Mountains in eastern Utah. The priority of publication and the geographical fitness of the name will probably secure its acceptance by mineralogists.* The following is Prof. Blake's article. In the month of September last, a sample of peculiar asphalt was received for examination, and recently when in Provo, Utah, I had the opportunity of seeing a considerable quantity brought in from the Uintah Mountains. It is obtained in masses several inches in diameter, and apparently free from mechanically disseminated impurities. It breaks with a conchoidal fracture, is very brittle, and is readily reduced to powder in a mortar. Hardness, 2 to 25. Gravity, 1.065 to 1.070. Color, black, brilliant, and lustrous; streak and powder, a rich brown. It is a non-conductor of electricity, and is electrically excited by friction.

Jan 1, 1888