Search Documents

By F. Lawson, N. A. Sareyed-Dim

A rotating disk of iron precipitant in a high temperature batch reactor has been used to study the kinetics of precipitation of nickel from low concentration aqueous solutions. Under inert atmosphere conditions, for temperatures up to 150°C, the rate of nickel deposition at pH25°C of 5 to 6 is controlled both by the rate at which nickel ions reach the surface and the rate of chemical reaction at the surface. However, the presence of oxygen in the atmosphere above the reacting system increases the nickel deposition rate dramatically. It is suggested that under the experimental conditions used, hydrogen atoms are adsorbed on both the iron and nickel, thus reducing the number of sites available for the cementation reaction. Oxygen acts as a depolarizer for hydrogen.

Jan 1, 1977

By T. F. Witherbee

Discussion of Mr. Baker's paper, read at the Lake Superior Meeting, September, 1904. MR. T. F. WITHERBEE, Durango, Mexico (communication to the Secretary*) : Mr. Baker's paper is very instructive in that it shows how furnace-derangements sometimes originate from apparently slight causes. In 1896 a similar burning through of the lining occurred at the Mayville furnace of the Northwestern Iron Co., Mayville, Wis., in exactly 38 days from the time the furnace was blown in. At that time I attributed it to the fact that the bell was carried several inches to the front side of the furnace, the length of the versed side of the arc described by the lever, thus dumping a little more of the charge on the back side, which made the front side of the furnace-charge more open and consequently increased the circulation of the furnace gases through it. After reading Mr. Baker's description, I believe that possibly a little more ore was charged on the back side of the hopper, due to the fact that it was nearest to the elevator. This unequal charging, however, was unconsciously done, as the fillers were both honest and faithful. The illustration of the burned lining of Furnace No. 1, given in Fig. - of Mr. Baker's paper answers very well for the Mayville furnace. It shows that in both cases the destruction of the lining was largely due to faulty construction, in that there were no cooling-plates in the angle of the bosh and in one or two courses of brick above it, where I believe they are-more in demand than anywhere else in the furnace. The presence of these cooling-plates at the angle of the bosh would have obliged the current of the hot gases to turn the corner and would have prevented them from following the angle of the bosh com¬pletely through the lining and shell.

Mar 1, 1905

By John S. Brown

The northeastern United States embraces that area of the Appalachian Mountains, and adjacent territory, beginning on the south at the Potomac River. It thus extends from the flat-lying Paleozoic terrane of the Appalachian plateau on the west, across the folded Paleozoics of the Great Valley and adjacent ridges (Paleozoic and Precambrian), over the Piedmont and New England metamorphic complex (mixed Paleozoic and igenous rocks), broken by the great Triassic rift remnants, onto the subdued coastal plain of Cretaceous and Tertiary sediments. Although not noted as a metal mining region, the area does contain numerous substantial and several outstanding mines, chiefly of the more prosaic metals, particularly iron, zinc, and copper, as well as many minor occurrences of these and a few additional items. These deposits occur to some extent in every subdivision of the area. The region to date (1966) has produced almost 500,000,000 tons of medium to lowgrade iron ore, especially magnetite, including ilmenitic magnetite; 50,000,000 tons of highgrade zinc ore; and 5,000,000 tons of lowgrade copper. In the past, it has yielded small amounts of chromite and nickel, and at present is a large producer of titanium. Precious metals are conspicuously absent, and so also are the Tertiary or Mesozoic igneous phenomena so commonly associated with mines of the West. Hence, a survey of the extensive mineralization · of this region should be instructive

Jan 1, 1968

By R. W. Raymond

THE death of Privy Councilor Bruno Kerl, on March 25, 1905, terminated a distinguished and useful career. Bruno Kerl was born March 24, 1824, at St. Andreasberg in the Harz, and entered in 1840 the mining school of Clausthal, where he studied for three years, working at the same time in the mines and stamp-mills. After an additional year of practice in the silver-reduction and iron-works of the Upper Harz, he passed his examination as a metallurgical graduate, and studied for a year at Göttingen under WV filer in chemistry, Hausmann in mineralogy, and eminent teachers in other branches. In 1846 he was employed at the Oker works, but very soon left this post, to become a tutor in chemistry, metallurgy, etc., at Clausthal, where he continued to labor until 1867. During this period the Clausthal school became a completely equipped Mining Academy, and Kerl was made in 1862 a full professor. Meanwhile, in addition to the work of instruction, he discharged, simultaneously or successively, the duties of many responsible official positions in the Royal Hanoverian administration of mines and smelting-works, and also published many valuable books and treatises. Among these were professional guide-books to the Upper and Lower Harz, and their characteristic metallurgical processes; a manual of qualitative and quantitative blow-pipe analysis; another of metallurgical assaying ; and, most important of all, a Handbook of Metallurgy in four volumes, the second edition of which was issued in Leipzig, 1861-1865. This book was speedily recognized as the leading authority in its field. In this country, the English translation and revision, by Crookes and Röhrig, published about 1869, had a large circulation. In addition to these literary labors, Prof. Kerl became in

Jul 1, 1905

By Richard McCaffery

CONTENTS PAGE 1. Research on Blast-furnace Slags (A Progress Report). By Richard S. McCaffery 5 2. Determination of Viscosity of Iron Blast-furnace Slags. By Richard S. McCaffery, Clarence H. Lorig, Ira N. Goff, Joseph F. Oesterle and Oscar O. Fritsche 27 3. Effect of Magnesia on Slag Viscosity. By Richard S. McCaffery, Joseph F. Oesterle and Oscar O. Fritsche 55

Jan 1, 1931

By Harold B. Fell

MANY oil producers are in disagreement with the idea held by some that an increase in the price of crude oil would be unlikely to stimulate much production and that we will be obliged to draw upon foreign sources of petroleum to supplement our domestic production as the years go by. Supporting our con trary opinion are numerous facts and figures. The most recent official estimate of the maximum efficient rate of production from the oil wells of the United States is 5,271,000 bbl per day. The Economics Advisory Committee of the Interstate Oil Compact Commission estimates, assuming certain supplies from imports and from natural gasoline and benzol, that crude oil require-

Jan 1, 1947

By Eugene McAuliffe

NO physical impairment can be more serious than the partial or complete loss of sight. With reasonably good eyesight, a person is equipped to care for life and I limb, provided a rational measure of t caution is manifested. When the sight of one eye is lost or badly impaired, one-half of this God-given asset is gone, and extreme care must be taken to prevent the tragedy of total darkness that closes out the beauty of sky, field and mountain, the faces of relatives and friends, and either removes entirely or in part one's capacity to produce and earn. During 1933, The Union Pacific Coal Co., operating ten coal mines in Wyoming, decided to undertake a visual survey of all of its mine operating officials and employees. Although the cost of workmen's compensation paid because of eye injuries was material, the management was more deeply concerned with the social loss and the suffering resulting from the many eye injuries. As every element of coal production cost must be scrutinized, accurate data on all accidents, with the workmen's compensation paid therefor, are carried forward monthly. The number of accidents to eyesight and the resultant compensation paid are shown in Table 1 for nine calendar years:

Jan 1, 1934

By J. T. Ryan

SAFETY practice or the elimination of accidents in our coal mines is specifically a problem of management. It cannot be delegated to any governmental agency except that the various coal-producing states do and should have some minimum safety standard laws. However, the legislative method of attempting to control mine accidents is ineffective because of the delay between the necessity and the action. It will always be impossible to keep our various state mining laws up to date; and when the law says you must do a certain thin there is a tendency to do this and no more. Unless the scheme for setting up state regulations is so flexible that when a new hazard develops it can be immediately and adequately covered and the whole responsibility for accident elimination placed undivided on the

Jan 1, 1937

By George C. Branner

STATE geological surveys have had an interesting development in this country. They first appeared more than a hundred years ago. The fact that they have persisted and are now an important part of most state governments indicates the basic need for state departments con-cerned with mineral problems. The number of state surveys in 1941 (43) is at an all-time high, as is the aggre¬gate appropriation for their support for the fiscal year 1940-'41 ($1,600,708). The first surveys, those of North and South Carolina (see Fig. 1), made their appearance in 1820-'30, but neither survived that period. During the next two decades surveys were created in twenty states, but only three survived. In fact, it was not until the decade 1900-'10, when eighteen surveys were created and only five abolished, that these agencies became firmly established.

Jan 1, 1941

By J. J. Jonas, J. L. Uvira

Equipment was constructed which permitted the hot compression of 99.8 pct Armco iron and 2.8 pct Si steel at constant true strain rates of 0.05 to 1 per sec over the temperature range 600" to 1000°C. A maximum true strain of 1.9 could be attained, followed by immediate quenching or by isothermal annealing. True stress-true strain curves were obtained, and the steady-state flout stress, a, strain rate, i, and temperature, T, were found to fit the following expression: The constants A, a, n', and AH were determined for the two ,materials. The activation energies obtained for Arrnco iron and silicon steel are 66 and 80 kcal per mole, respectively, and approximate those for seu- diffusion and for creep. This indicates that hot compression is a diffusion-controlled thermally activated process. THE hot compression of iron and steel is usually carried out in the austenite temperature range,1"7 as this is the one of greatest interest with respect to industrial hot working. However, a disadvantage of testing in the austenite range is that the hot-worked structure is destroyed by the phase transformations taking place during cooling. The present study was therefore carried out in the ferritic temperature range, and the hot-worked substructures were preserved by rapid quenching after deformation. The substructural results will be described in a separate paper, and the present communication is restricted to the strain rate/stress/temperature relationship observed during hot working. The results of hot-compression testing are usually given in the form of true stress/true strain curves, with a different curve for each temperature/strain rate ~ornbination.',~,~ Sometimes simple algebraic equations are fitted to the curves, so that certain extrapolations or interpolations can be performed.1'2'5 These equations are, however, devoid of mechanistic interpretations. The present study was undertaken to show that hot compression can be described by an equation of the type used in creep studies. That is, it will be shown that the temperature dependence of the strain rate in hot working is well-represented by an Arrhenius term, with an activation energy similar to that for creep. Also it will be seen that the stress dependence of the strain rate is similar to that for creep EXPERIMENTAL METHOD AND MATERIALS The investigation was carried out with the following three ferrous materials: 1) Armco iron; 2) Armco iron with 0.26 pct Mn; 3) 2.8 pct Si steel. The first two materials were utilized for investigations performed in the temperature range 600" to 800°C; the last one was used for tests at temperatures from 600" to 1000°C. The materials were of commercial purity,* as shown in Table I. Cylinders of five different sizes were prepared by strain annealing. The resulting mean grain diameter was 3 mm in the 1-in. Armco iron and 2 mm in the other sizes and grades. Different ratios of diameter/height were used to enable the determination of the coefficient of friction. The specimen faces were provided with concentric grooves, which acted as lubricant holders during compression, as recommended by English and ~ackofen' and others.2'9 Powdered glass lubricants were applied to the samples before hot compression to decrease friction and barreling, following the practice of previous investigator~.~~~~~~~~ Different mixtures of glass powder were used for each temperature, after the determination of suitable compositions by experiment.'' Equipment for Hot Compression. Hot-compression tests were carried out on an adapted 150-ton vertical hydraulic extrusion press and also on a modified high-temperature creep machine. The modified extrusion press was used for temperatures up to 800°C. The following items were added to the press: a) a high-temperature furnace with built-in upper and lower platens; and b) a transmission assembly, which permitted the attainment of logarithmically decreasing crosshead speeds. These accessories are described in detail in Ref. 11.

Jan 1, 1969

By Thunaes, Arvid

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 1, 1950

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By C. P. Kempter, H. L. Brown

Recently Chang determined heat content values of tantalum monocarbide and tungsten monocarbide from 325" to985°Kand 326" to 912"K, respectively, and, using other published data, made certain solid-state calculations for these two compounds. Chang expressed his Cp values in units of cal per "g-atom alloy" OK. We consider this poor usage since l) tantalum monocarbide and tungsten monocarbide are not alloys, and 2) an atom of an alloy does not exist. However, one may convert his values to units of cal per mole OK by merely doubling them. For TaC he calculated a Nernst-Lindemann parameter of 9.07 x lo-' "g-atom per cal". We have refined the calculation of this parameter and have arrived at a much lower value. Rather than approximating the true coefficient of volume expansion, a,, as three times the true coefficient of linear expansion, a, we calculated u, from the TaCo.99, lattice expansion data of Fries and Wahman.38 At 25°C a, = 14.3 x 10s per OC. The molar volume was calculated to be 13.32 cu cm per mole at 25°C. From the lattice compression data of Champion and Drickamer~' for "TaC,.,," we determined the room-temperature compressibility to be 3.5 x 10-l3 sq cm per dyne by plotting l/Vo (aV/ap) vs applied pressure. (Since the lowest pressure at which Champion and Drickamer reported a relative volume was 20 kbars, one may calculate an approximate compressibility only. Chang calculated a compressibility of 3.175 x 10-l3 sq cm per dyne from the same data.) We also used twice Chang's value of Cp = 4.38 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated a Nernst-Lindemann parameter of 5.8 x 10-l4 mole per erg or 2.4 x lo- ' mole per cal, and a Cdil value of 2.3 x 10' ergs per mole OK. In the case of tungsten monocarbide no isothermal compressibility has been reported; however, one may calculate an approximate Nernst-Lindemann parameter by using the adiabatic compressibility reported by Brown, Armstrong, and Kempter." Using the WC lattice expansion data of Mauer and Bolz~l we calculated a, to be 12., x l0-' per OC. The molar volume was calculated to be 12.5 cu cm per mole. We used twice Chang's value of Cp = 4.18 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated an approximate Nernst-Lindemann parameter of 2 x lo-' mole per cal, which is much

Jan 1, 1969

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By Jay J. Burns

TWO zinc concentrating mills are operated by the St. Joseph Lead Co. in St. Lawrence County, N. Y. The Edwards mill is operating at present only sixteen hours a day treating 400 tons daily. The metallurgy at Edwards presents no unusual problems therefore this discussion is mainly limited to the metallurgy of the Balmat ore. The Balmat mill has a capacity of 1,250 tons per day and the operating crew consists of three shift bosses each with five millmen per shift. Two crusher operators work on each of two shifts and one cleanup man on day shift. The repair crew is made up of a foreman and three repairmen, one of the repairmen being capable of taking over any operating job in the mill from shift boss down. Each millman is capable of handling the next job in line and several men in the yard crew are broken into handling the start-off job in the mill so that temporary shortages of men do not cause extensive overtime. Sphalerite, pyrite, and galena, the principal ore minerals, occur in a gangue of calcite, dolomite, and silicates, especially diopside, plus tremo-

Jan 1, 1947

By Walter Miller

DURING the second year of America's active participation in the war the main objectives of the petroleum refining industry were again to provide the four most important product needs for war: 100-octane aviation gasoline, toluene for TNT production, high-quality lubricating oils for the needs of aviation and the armed forces, and petroleum chemicals for synthetic rubber manufacture. All other materials supplied by the petroleum industry took an inferior priority ranking, depending on the degree of essentiality. To accomplish the above objectives the industry initiated and carried on a building program during 1942 and 1943 which will put those two years down in petroleum refining history as the greatest construction years of all time, a record which will hold for decades to come. Led by an estimated total of $900,000,000 going into 100octane and contributory plant investment, it is easy to picture a total of two billion dollars and more going into additional refining-industry plant investment during 1942 and 1943, most of it privately paid for, but a substantial part covered by R.F.C. Government money financing.

Jan 1, 1944

By E. M. Murphy

(Presented by invitation at a meeting of the Spokane Local Section of the Institute, Feb. 17, 1912.) EIGHT years ago the Hecla mine, a lead-silver producer, situated at Burke, Idaho, was producing ore from but two levels, the 300- and the 600-ft. All hoisting was done with a 12- by 16-in. slide-valve, double-reel, hoist. The hoist was being worked to its capacity and was unsuitable for hoisting from greater depths. As the work of opening a new level was about to be started, it became necessary to remodel the then-existing equipment or install a new hoist. The recent advent of electricity from Spokane had made available a cheaper power than steam. By a series of tests conducted throughout the Coeur d'Alène district, it was found that it cost $109 per year to generate a horse-power with steam. Electric power was to be had for $50 a horse-power per year. It was decided to substitute for the engines a motor-drive, of sufficient capacity to operate from the 900-ft. level, and ultimately install an entirely new hoist. After disconnecting the engines, installing a new shaft, and making a few minor changes, a 300-h-p., 2,300-volt, 514-rev. per min., variable-speed motor of the induction type was geared to the reel-shaft. The reels were supplied with 3/8 by 4-in. flat rope, and the duty of the hoist was about as follows: Cage, 1,700; ore, 2,600; car, 1,400; rope, 2,250; total, 7,950 pounds. The Bristol ammeter chart, Fig. 1, shows the combined current-consumption of the hoist- and mine-motors. The large intermittent load is clearly shown ; this produced harmful fluctuations in the voltage of the long, lightly-loaded, 60,000-volt transmission-line from Spokane to the Coeur d'Alènes. The power company received no compensation for the increased cost of producing power for this intermittent or fluctuating load. In order to protect its system from similar excessive

Sep 1, 1912

By S. H. Penn

One of the more challenging aspects of the unfolding age of space travel centers about the opportunity for man to use the natural resources of other worlds. The first of the extraterrestrial worlds to be exploited will be the moon. After only a scant few thousand years of scratching the earth's crust, man will embark upon a venture that for centuries has excited the imagination of many (while staggering that of most) and may become a reality within the next decade. There has never been a time when so much money and effort will have been expended to exploit an area about which so little is known. Paradoxically, this effort combines much of the detached objectivity so typical of our analytical time with the proverbial optimism of the indefatigable prospector. As the earliest manned lunar missions will be brief and exploratory in nature, astronauts will not be expected to attempt to exploit any of the possible lunar natural resources. In later missions, with a more extended period of time available for the astronauts to stay on the moon, it may be desirable or even necessary to "live off the land". The resulting exploitation of lunar resources will be intended primarily to reduce the dependence of manned missions upon terrestrial logistic support and to reduce the cost of maintaining lunar bases.

Jan 3, 1966

By M. E. Straumanis, J. -P. Krumme

In basic ([KOH + KCl] with a total polarity of 2) or acidic (2N H2SO4) electrolytes and at anodic current densities of more thun 2 to 4 ma per sq cnz, n-type GaAs single crystals of lozo resistivity preferentially dissol~je forming etch tunnels with triangular or civc~ilay cross sections and of a width between 0.5 arid 5 p. These etch tunnels are oriented along any one of the four possible (111) directions of GaAs. However, their growth occurs only in one direction of a given (111) whick apparently is determined by the atomic sequence Ga —As (and not the rezlerse) in respect to an individual valence bridge in the crystal. It is concluded from comparison with the cubic lattice structure of GaAs that the etch tunnels represent macroscopic evidence for the tetrahedral bonds and their polar properties. If the anodic current density is increased the tunnel fomation results in the development of a fibrous surface layer consisting of GaAs. The latter separates frorn the substrate (in an anodic s~irface disintegration process) by the growth pressure of an As,0, filnz forming in the interior of the fibrous layer, 100 to 200 µ under the surface, at more than about 50 ma per sq cni. The fibrous GaAs film has the same crystallographic orientation as the substvate and represents a skeleton of the original crystal. Since the etch-tunnel density in a separated GaAs layer is about 108 c?n-', and the etch tunnels develop only along (111) in a given polar direction, it is assurraed tlmt the dislocations have no influence on the growth of these tunnels. ElECTROLYTIC treatment of smooth surfaces of poly- and single-crystalline GaAs at high anodic current densities causes the formation of porous surface layers.' This phenomenon suggests comparison with effects being observed with magnesium,' indium,, gallium,4 and aluminum5 and known as "anodic disintegration". The purpose of the present paper is to explore and to explain the reasons for the formation of such surface layers on GaAs and, in particular, to investigate the influence of the lattice polarity of this III-V compound semiconductor in the (111) direction on the anodic dissolution behavior. GaAs SINGLE CRYSTALS For the experiments described below GaAs single crystals from the Monsanto Co., St. Louis, Mo., were used. Their impurity levels were below 1 ppm and their dopant levels between 1 and 100 ppm. They were grown in (111) using the Czochralski or the gradient-freeze technique. The crystals had n-type conductivity and electric resistivities between 1 and 5 ohm-cm. EXPERIMENTAL The GaAs single-crystal rods were cut perpendicularly to (111) into wafers of about 1 mm thickness using a wire-blade crystal slicer and an aqueous slurry of Sic or a diamond saw. The orientation of the faces of these wafers were checked by Laue back-reflection patterns. If there was a deviation from (111) the faces were abraded under a certain angle using grinding paper and distilled water. The damaged surface layer was removed from each crystal by chemical etching with a mixture of 1HF:1HNO3: 1H20 or 2HF:1HNO3:2HAc (glacial). {110) faces were obtained by mechanical cleavage, producing surfaces which did not require a further treatment. The GaAs wafers were mounted using "alligator" clamps instead of soldered electrical contacts.' Only the bare crystal surfaces were dipped into the electrolyte. The clamps were coated with insulating wax to prevent any contact with the electrolyte. The experiments were carried out in aqueous 2 N H2so4,' or in an aqueous solution of KOH and KCl1 (1 mole KOH + 1 mole KCl in 1000 cu cm solution). Anodic current densities up to several hundred ma per sq cm were applied for periods between 30 sec and 2 hr. For the purpose of investigating the initial steps of disintegration the anodic current density applied never exceeded 20 ma per sq cm. The films which partially separated from the anodic surfaces under high-field conditions were treated with KOH to further their detachment by dissolving the As2O3 formed. The washed and dried films were pasted to strips of filter paper, and Laue pictures were made. The back-reflection patterns obtained were compared with those of the original anode surface before and after anodic dissolution. Furthermore, space reciprocal lattices7 were constructed from asymmetric rotation crystal patternsa which permitted the determination of the crystallographic orientation of the detached films of the corrugated anodic surfaces. The disintegration products were identified from assymmetric powder patterns.8 The polarity of the {111) faces was determined by chemical etching with mixtures of 1HF:1H2O2(30 pct): 2H2O or 1HNO3:2H2O. Different patterns on each of two inverse (111) sides appeared.'-l8 The correlation of these patterns to the Ga{111) or the As(111) side has already been established by the use of light figures,18-20 by X-ray diffraction near the absorption edges of gallium and arsenic,'lmZ4 and by LEED measurements.25 The geometric structure of these surfaces and the interior of the anodically attacked crystals were observed and photographed with a high-power microscope using oil immersion objectives up to magnification of X1720.

Jan 1, 1968

IN accordance with a programme arranged by a committee of the Institute, consisting of Mr. William P. Shinn, of St. Louis, chairman, and Mr. Joseph D. Weeks, of Pittsburgh, secretary, the member's of the Institute, with their ladies and invited guests, assembled in Chicago on Sunday morning, August 22d. A special train, provided by the Chicago and Northwestern Railway,. left Chicago on Monday morning at 7.50 o'clock, and conveyed the party to Marquette, arriving at 9 o'clock P.M. Here the steamer Northern Queen, which had been chartered by the committee for the accommodation of the Institute, was in waiting, and the members and ladies at once took up their quarters on the boat. EXCURSIONS IN THE MARQUETTE IRON REGION. Local Committee. EXECUTIVE. -J. C. Morse, chairman; C. Y. Osburn, secretary ; D. F. Wadsworth, treasurer; C. H. Hall, H. Merry. RECEPTION.-S. P. Ely, J. P. Pendill, E. Breitung, W. F. Swift, A. P. Swineford, J. C. Fowle, C. G. Griffey. TRANSPORTATION.-Samuel Schoch, D. Morgan, D. H.. Merritt, J. Pickands. FINANCE.-Peter White, A. W. Maitland, W D. Rees, E. R. Hall. EXCURSIONS.-W. E. Dickinson, H. A. Burt, A.. Kidder, C. E. Wright. REFRESHMENTS.-J. Q. Adams, H. H. Stafford, Joseph Kirkpatrick, D. H. Bacon. On Tuesday the iron mines in the vicinity of Negaunee and Ishpeming were visited, transportation being provided by special trains on the Marquette, Houghton and Ontonagon Railroad. In the morning the McComber, South Jackson, and Jackson mines were inspected, and in the afternoon the Cleveland, New York, Lake Superior, and Barnum mines. Dinner was provided at Negaunee, and gracefully served by, the ladies of the town. In the evening the first session of the Institute was held in the saloon of the steamer. The President, William P. Shinn, of St. Louis, congratulated the Institute on the happy consummation of the wishes of its members to have a meeting on Lake Superior. After tedious and baffling negotiations arrangements had been com-

Jan 1, 1881