Search Documents

By D. L. McElroy

SAFETY in coal mining received especial attention by the public in general and the mining industry in particular during 1940 and early in 1941, owing primarily to the six explosion disasters which occurred last year with a total of 276 fatalities. This was the largest number of fatalities due to explosions in bituminous coal mines since 1928, when 347 lives were so lost. But facilities due to explosions have had a definite decreasing trend since 1907, in spite of bad years such as 1917, 1924, 1932, 1937, and 1940. Although the upswing in explosion fatalities in 1940 is lamented by all, none will admit it represents a trend and it will serve mainly to stimulate ways and means of further reducing these disasters.

Jan 1, 1941

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By Jan H. Hommen

TRENDS IN MINE FINANCE Reviewing historical trends may help in dealing with future funding strategies. The first trend is the increase in the use of debt to fund corporate America. Surprisingly, when comparing that with other corporates in the global marketplace, the U.S. does not look too poorly. Japanese, in particular, but also German companies, are much more leveraged than their U.S. counterparts. Note that in Japan and Germany the government and the consumer have shown substantial restraints when it comes to credit. Not so in the U.S. where the savings rate (4%) is much lower than that in Japan (20%) and in Germany (14%). As a result, the cost of leverage is substantially lower in Japan and in Germany than in the U.S. Lower debt costs in these countries allows one to obtain more of it for the same price. The close relationships between financial institutions, corporations and governments in Japan and Germany also make the risk of leverage more bearable and understandable. Also note that interest rate volatility in these countries is more subdued. The investor base in common stock is also changing. Private pension funds have been net sellers of equities during the last few years while public pension funds have been net buyers. Individuals are basically out of the market. It is estimated that over $330 billion of equity was retired in the U.S. through 1986-1988. The reasons are well known: restructurings, buy-backs, takeovers, mergers, and buy-outs. This de-equitization is likely to continue as the cost of equity capital is higher than the cost of debt capital, even on a before-tax basis. Because there has been no market for equity since October 19, 1987, junk bonds have replaced equity capital in the corporate finance structure. The non-investor-grade borrower has access to the public markets through high-yielding debt securities that often look like senior equity. Deregulation has also provided 24-hour markets; securitization can now liquify assets that before were rusting on balance sheets; information processing and communication tools give facts that are instantaneously available, creating the need for products to cover risk and exposures unknown before the start of the information and technology explosion. Thus we now have swaps, options, futures, options on futures, caps, as well as program trading, portfolio insurance, index funds, etc. Globalization will be unstoppable. Today's environment demands it. Corporations are now global competitors, even though they may have never shipped a product off-shore. Boundaries are disappearing and impediments have been removed. Stocks can be issued in a global offering with distribution in all major financial centers of the world. The high leverage of Japanese companies has made common stocks very scarce, which with the high savings rate, makes equity capital inexpensive in Japan. If markets were perfect everyone would issue stock in Tokyo and buy it back in New York. This would certainly stop the bleeding on the balance of payments. With the deficit balance of payments in America, it is no surprise that the cost of money is expensive here. The risk-return relationship on U.S. equity is not favorable enough to appeal to Japanese equity investors. The Tokyo-market, helped by a stronger yen, surpassed New York as the most important equity market in the world. The question is, will the Tokyo market hold up when Japanese domestic consumption increases at the expense of savings? In the U.S. debt markets, the plain vanilla debenture is making a comeback after a period of absence. Commercial paper has replaced short term bank borrowings for working capital funding by larger corporations. The banks have made an interesting comeback with loan sale programs that will continue to attract borrowers. There will be a continuing

Jan 1, 1990

By William D. Southard, Joseph W. Schlitt, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott 's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12-15% moisture could be consistently delivered for smelting.

Jan 1, 1980

By R. E. Phelan

WHILE 1931 was a most important year in the history of Canadian copper smelting and refining, nevertheless, due to the low price of copper and the in- ability of the International Nickel Co. to market its full capacity of nickel. the production of both copper and nickel was considerably less than the total installed capacity for the production of these metals. IIY the nor- mal course of events, 1931 should have seen a great increase in the production. of both copper and nickel in Canada, because the large extensions to both the copper smelting plants and the copper and nickel refinery capacity, which had largely been completed in the year 1930, should be showing their effect.

Jan 1, 1932

By Edward Steidle

TWO years ago the Committee on Latin American Education Relations, Mineral Industries Education Division, started a study of mineral industries education in the Latin Americas. Information was obtainable only with great difficulty. Some information was available piecemeal but no complete resume had ever been assembled. Initial assistance was gained from the United States Office of Education and the Pan American Union. This, and first-hand knowledge of the writer, provided a list of colleges and universities which were believed to offer work lead. ing to a degree in one or more branches of the mineral industries. Detailed information could be obtained only by direct contact with each university through air mail service. Questionnaire letters were sent to officials of 34 colleges and universities. Twenty-one gracious replies were received. Fourteen of the colleges and universities concerned offer curricula in mining, five in metallurgy, three in petroleum, seven in geology, one in geographical engineering, one in topographical engineering, and one in geophysics. Two institutions offer advanced training in petroleum engineering. No institution offers any courses under the caption of ceramics or fuel technology.

Jan 1, 1945

By F. F. Aplan

Mineral processing engineers have recorded an- other year of active research and development work. Most gratifying was the broadly based attendance at the Mineral Processing Fundamental (formerly Basic Science) Committee sessions at the 1968 Annual Meeting of the AIME. Because of the availability of good papers, the active discussion and the growing attendance, sessions have grown from one to three at the annual meeting. Prof. M. C. Fuerstenau of the University of Utah will chair the Mineral Processing Fundamentals Committee for the next two years and we may thus be assured of continued active leadership. The name change from "Basic Science Committee" to the more descriptive "Mineral Processing Fundamentals Committee" approved by the MBD executive council is a welcome improvement. Our profession continues to attract the interest and cooperation of those in other professional groups. The 1968 Engineering Foundation Particulate Matter Conference, under the chairmanship of John Karpinski of Bethlehem Steel, was devoted exclusively to comminution this year. It attracted conferees from five continents and served as a particularly stimulating source of interchange of knowledge from many technical fields. Next year's conference will be under the chairmanship of Professor L,. G. Austin of The Pennsylvania State University. This conference plus the Symposium on Wettability and Flotation to be held at the annual American Chemical Society meeting in Minneapolis in April indicates the success achieved in the inter-disciplinary approach to problems. Other evidence of this spirit of professional cooperation is the forth- coming book on Size Reduction edited by D. W. Fuerstenau. This is the outgrowth of an AIChE symposium on size reduction held in 1965.

Jan 2, 1969

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,' and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.' Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8'7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8'9 Copper minerals sometimes yield elemental sulfurlo'" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,'5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By A. T. Yu

The energy crisis and the resurgence of mining activities highlighted 1972-73. Added to the impetus for more effective materials handling systems has been the continued upward trend of inflation and labor costs. The need for addressing the fundamentals has led to the trend toward an overall systems approach to materials handling problems.1 The decision to move forward with large mining ventures such as the $150 million Hibbing taconite comple2 and the immense Carajas iron project must base themselves on indepth studies of a host of factors viewed in the context of an integral mine-transport-market system. What's important is that each ton of pellet or ore must be an economical commodity at the end users' furnace. The project can still be viaable even if certain components in the entire network appear to be individually costly.

Jan 2, 1974

By H. O. Hofman

WITH the exception of lead sulphate, all common metallic sulphates are completely decomposed upon heating into metallic oxide, sulphur trioxide, sulphur dioxide and oxygen. Some give up their trioxide readily at a low temperature, others require considerable heat and much time to be completely freed from sulphur. Kerl in 1881 arranged the principal metallic sulphates as they are decomposed by a rising temperature in the following order: silver, iron, copper, zinc, nickel, cobalt, manganese and lead, lead sulphate being decomposed only slightly at a white heat. The researches of Bradford, published in 1903, show, however, that ferrous sulphate is decom¬posed at 590° C., cupric sulphate at G53° C. and argentic sulphate at 1,095° C. By the present investigation it will be seen that zinc sulphate is decomposed at 739° C. As far then as our present knowledge goes, the order in which the decomposition of the leading metallic sulphates takes place is the one given in Table I.

Jan 1, 1905

By AIME AIME

The Washoe plant, 1 in Anaconcla. Mont., together with the local street-railroad, ranches a. foundry and machine-shop a brick-plant and the Montana hotel, form a property under one management; to which should be added the mines in Butte owned by the company, from which part of the ore-supply of the plant comes. The Anaconda Copper Mining Co., controlled by the Amalgamated Copper Co., was reorganized under the laws of Montana in 1893. A map of the plant, showing the numerous departments and illustrating the details of tracks, pipe-lines, and charging-stations for compressed-air locomotives, is given in Fig. 1.

Jul 1, 1906

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee. Each year the Nominating Committee is to select "official" candidates for eight places, as follows:, (1) President and Director (2) Vice-President and Director (3) Vice-President and Director (4) Director (5) Director (6) Director (7) Director (8) Director

Jan 1, 1939

By A. C. Fieldner

THE COMMITTEE on Correlation of Research held two meetings in 1931. The first was a luncheon meeting on Feb. 19, at the Engineers Club, New York, attended by eight members and four guests-William H. Bassett, past-president of the Institute; Robert E. Tally, president; H. Foster Bain, secretary; and Alfred D. Flinn, director of the Engineering Foundation. Mr. Bassett gave a short resume of the circumstances leading to the formation of the Committee and expressed his opinion that the objectives as expressed by the Committee in its first annual report were in accordance with the ideas of the Institute officials. Mr. Tally stressed the great importance of research in the mining and metallurgical industries and stated that lie believed the Institute should encourage and promote research, and that this Committee could do a great deal to foster such work in the Institute. Mr. Bain pointed out that this Committee was appointed with a view to correlating and fostering research work. in the field of the Institute's activities. This could be done in various ways, as by encouraging the divisions and committees of the Institute to hold group meetings on research, by forming research subcommittees in the Institute divisions, and by bringing together research interest in. certain projects and the fund or organization that is equipped to carry out the project.

Jan 1, 1932

ON Oct. 5, 1926, the day before the general ses-sions of the fall meeting of the American Insti-tute of Mining and Metallurgical Engineers at Pittsburgh, a round table conference on the combus-tibility and testing of coke was held at the Bureau of Mines Experiment Station. There were about fifty present, with A. C. Fieldner, chief chemist of the Bureau of Mines, as chairman. The following organi-zations were represented: American Institute of Min-ing and Metallurgical Engineers, American Society for Testing Materials, American Gas Association, Eastern States Blast Furnace and Coke Oven Association, Gas and Fuel Division of, American Chemical Society, and Southern Ohio Pig Iron and Coke Association. In opening the proceedings, Mr. Fieldner explained that the meeting had been called at the suggestion of several members of the Institute and members of other organizations. The subject is of interest to the pro-ducer and the user of coke whether it be in a blast furnace, cupola furnace, house-heating furnace, open grate, gas producer, or in a water-gas generator. There has been much confusion on this subject largely because there is no common definition of combustibility. Does the blast-furnace superintendent, the coke-oven operator, and the fuel engineer have the same under-standing of the term "combustibility"? If a common understanding can be reached, many differences of opinion will disappear. COMBUSTIBILITY OF COKE R. H. Sweetser of Columbus, Ohio, disagreed with the statement of P. H. Royster, T. L. Joseph, and S. P. Kinney in Reports of Investigations, Serial No. 2524, of the Bureau of Mines, in which it was stated that the coke-oven op-erator cannot change coke combustibility by modifying oven practice. Mr. Sweetser held that the coke-oven man can change the combustibility of coke. Blast-furnace men know that coke that will burn easily with low pressure and will. come down in the regular way in the furnace can be pro-duced from a given mixture of coal. His idea of the combustibility of coke is the rate of flow through the com-bustion zone of the blast furnace. If the coke does not pass through in normal manner it is highly incombustible. H. J. Rose of the Koppers Co., Pittsburgh, objected to being pinned down so closely on this phase of the com-bustibility and incombustibility of coke. Coke-oven men are frequently obliged to change oven conditions to make a coke which gives blast-furnace men what they want. The size of the coke and the screening have an important bear-ing on combustibility, and there are many cases on record where by simply changing the different sizes of the coke, everything worked smoothly, and that is a much more combustible coke.

Jan 1, 1927

By C. K. Gupta, P. K. Jena

Niobium (columbium) metal in the form of a button has been produced by calciothermic reduction of niobium pentoxide using sulfur as the heat booster. In these experiments with 50 g of niobium pentoxide per batch, the influence of percentage of calcium in excess of the stoichiometric, the percentage of sulfur by weight of the niobium oxide, and the outer-wall temperature of the bomb on the quality and yield of the metal has been studied. The maximum yield on this scale was 78 pct using 50 pct excess Ca and 20 pct of S and at a bomb-wall temperature of 600°C. In experiments conducted on 500 g of niobium pentoxide, reduction with 40 pct excess Ca and 20 pct of S, and at a bomb-wall temperature of 500°C, the.yield of the metal improved to 82 to 84 pct. Some of the reduced-metal samples have been electron-beam melted and the button melts thus obtained have been observed to be extremely ductile and capable of cold reduction to 98 pct without intermediate annealing. NIOBIUM, because of its high melting point (2468oC), its ductility, its resistance to corrosion especially in liquid metals, its high-temperature mechanical properties, and its relatively low capture cross section (1.1 barns) for thermal neutrons, has potentialities as a structural material in the field of nuclear engineering. Niobium and its alloys are also gaining importance in high-temperature technology as components in aircrafts, jet engines, and missiles, electronics, chemical engineering, and surgery. In 1904 Weiss and Aichel 1 produced niobium by reduction of its pentoxide by misch-metal. Since then a large number of investigations have been carried out for the extraction of niobium from its compounds. The various routes through which the metal niobium has been extracted from its compounds can broadely be classified into the following groups: a) reduction of its halides, oxides, and fluo-salts with metals like calcium, magnesium, sodium, and aluminum;2-10 b) reduction of its halides with hydrogen and oxides with carbon or carbides;11-18 c) electrolytic winning from its halides and fluo salts;19-25 and d) thermal decomposition and disproportion ion of its halides26-30 Among the processes in commercial use at present are sodium reduction or fused-salt electrolysis of potassium niobium fluoride, carbide or carbon reduction of the oxide, and hydrogen or metallothermic reduction of the chlorides. In 1907 Von Bolton2 prepared niobium by reducing niobium pentoxide with aluminum. Dennis and Adam-sona attempted reducing the oxide with magnesium powder in argon atmosphere and the resulting metal contained as much as 5 pct O. Mondolfo8 claimed a method for the reduction of the oxides with aluminum. In the case of both magnesium and aluminum reduction, it has been stated31 that by-product oxides such as MgO or A12O3 would involve a major separation problem. Further, in the case of alumino-thermic reduction, the solubility of aluminum in niobium and intermetallic formation have to be reckoned with. In 1922 Bridge3 produced niobium by calcium reduction of niobium pentoxide. Dennis and pdamson' obtained the metal by a similar method with an oxygen content of 0.2 pct. In most of the cases of metallothermic reduction of niobium oxides mentioned above, the metal niobium is obtained in the form of powder. In an attempt to produce massive niobium metal, lock' used iodine as the thermal booster in the bomb reduction of niobium pentoxide by calcium. Massive niobium metal was obtained with a maximum yield of 75 pct containing 0.1 pct 0. Joly32 carried out experiments on calcium reduction of niobium pentoxide on a 2-kg scale using sulfur as the heat booster in a sealed bomb filled with argon. In his experiments, the reaction was initiated by passing a current through niobium spiral wire embedded in the charge. In a typical run consisting of 2000 g of niobium pentoxide, 3100 g of calcium, and 800 g of sulfur (S/Nb2O5 = 3.3), he obtained massive metal in the form of a very uneven mass with a yield of -57 pct. With lower amounts of sulfur and calcium, powder niobium mixed with small metal globules was obtained and the yield was also poor. From these experiments he concluded that this method is not a suitable one for industrial development considering the quality and yield of metal obtainable and the possible hazards with higher ratios of sulfur to niobium pentoxide in the -~charere. In the present work, a detailed investigation on the calciothermic reduction of niobium pentoxide in a stainless-steel bomb in presence of sulfur as the heat booster was undertaken on a laboratory scale.

Jan 1, 1964

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By H. O. HOPMAN

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. THE substance of this paper was prepared for the Seventh International Congress of Applied Chemistry, held in London, May, 1909, under the title, Some Developments in Blast-Roasting. In the absence of the author, a -short abstract of the paper was read, and the abstract only will appear in the proceedings of the congress. The present paper has been partly rewritten and considerably enlarged by information gained since the original was prepared ; also some illustrations have been added. Blast-roasting' is a generic term for the process of forcing air through finely-divided. metallic sulphide with the object of roasting and agglomerating in a single operation. At first the process was confined to a galena-concentrate ; lime, limestone, or gypsum was added, to serve both as a diluent to keep separate the particles of galena that they might be thoroughly oxidized, and as a flux that the partly-roasted ore might be agglomerated by the formation of some slag. Later it was extended to treat other metallic sulphides. The leading processes were the Huntington-Heberlein and the Savelsberg of Europe, and the Carmichael-Bradford of Australia. In the United States and Canada, the Huntington-Heberlein process has found application in some instances with galena-concentrates, for which it was originally intended; but this class of ore is not often treated alone, hence the process has had to be modified to suit conditions. The Savelsberg process has been transplanted to this country in about its original form. The Carmichael-Bradford is not used at present. The changes called for in the Huntington-Heberlein process to adapt it to the class of lead-bearing ores usually smelted have been the 1 A. S. Dwight, Engineering and Mining Journal, vol. lxxxv., No. 13, p. 649 (Mar. 28, 1908).

Jun 1, 1910