Search Documents

By Earl Bardwell

THE determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. THE EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows:

Jan 8, 1914

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By Paul E. Nilles

For every single BOF heat, the steelmaker must control the refining operation in order to satisfy at turndown the following conditions : - to reach the correct steel analysis (C, S, P, ...) in the shortest time possible, i.e. without reblow; - to maintain the temperature of the metal in a narrow range; - to produce the optimum steel weight. It is obvious that during refining limited time and scarce information are available and only very few corrective actions can be taken. For this reason, it is of the greatest importance to facilitate the control of the BOF process by taking adequate measures before and during charging of the converter. These are : - the availability of accurate and reliable equipments for the classical measurements, 5.e. weights, temperatures, flow-rates, analyses, etc... - the operation of an optimal charge calculation model which takes into account all information concerning the preceeding heats and the charged materials. '

Jan 1, 1972

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Directors of the A. I. M. E., through their monthly meetings, a report of the year's progress is almost superfluous. ' To the members who read the monthly reports of the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed or were working in other industries. Toward the end of the year, higher metal prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 1, 1925

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems.

Jan 12, 1957

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

By W. H. Bassett, C. H. Davis

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other. words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. . In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1928

By Gordon E. Agar, David M. Hopstock

This paper describes the procedures and results of a series of experiments conducted to determine the depressing effect of sodium, calcium and magnesium ions on the amine flotation of quartz. It also presents an analysis of the experimental results by the electrical double layer theory. The flotation of quartz with primary amines has been practiced on a large scale in the phosphate industry for many years. Some glass sand —and recently iron ore — has also been treated by this flotation technique. These applications have been highly successful and demonstrate that a complete mastery of all the details of an operation is not needed to achieve an economic success. There are times, though, when it becomes important to recognize, both qualitatively and quantitatively, the effects of some previously ignored variables. The effects of cations on the amine flotation process, particularly those ions that contribute to water hardness and abound in sea water, are a case in point. In conjunction with the development of a cationic flotation reagent for separating quartz from apatite, it became necessary to quantify the influence of calcium and magnesium on the separation. In order to strengthen and broaden current understanding of the flotation process, the results were interpreted by means of the electrical double layer theory. THEORETICAL BACKGROUND Assume that, given the same equipment, procedure, and time, the recovery of quartz by amine flotation is a function of only the adsorption density of aminium ions in the Stern layer, i.e., that for any given adsorption density there exists only one recovery percentage. By the Stern-Grahame treatment of the electrical double layer,'-' for any ionic species in a solution in equilibrium with quartz,

Jan 1, 1969

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.' The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

Jan 1, 1915

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By J. W. H. Clare

An equilibrium isotherm at 550°C is given for ternary alloys rich in aluminum containing 0 to 15 wt pct Cr and 0 to 20 wt pct Mn. Phases encountered are: aluminum solid solution; stable temary compound G; and MnAl8,. In addition, a limited number of alloys were annealed at 450°C to check for differences from the 550°C isotherm. These experiments limited the composition of the G phase at 550°C and further experiments established that the G Dhase is not stable above 590 ± 1 °C. RAYNOR and Little1 established several equilibrium isotherms using aluminum-rich alloys containing up to 5 pct of the elements chromium and manganese. These isotherms showed that, in addition to an a solid solution and the two binary intermediate compounds 8 and MnAl6, a stable ternary compound ex-isted in the system. This phase was called the G phase because of its ghostly appearance in micro-sections. Little, Raynor, and Hume-Rothery2 found a similar phase in binary aluminum-manganese alloys and, as a result of their experiments, concluded that the G phase was a metastable phase existing in the aluminum-manganese system. This phase was stabilized by the addition of chromium. The constitutional work of Raynor and Little,' although showing the existence of the G phase in the aluminum-chromium-manganese system, did not establish precisely the composition limits of the phase or the temperature above which the phase became unstable and disappeared from the system. The work described in this paper was undertaken to provide this information. An examination of the previous work' showed that an isotherm at 550°C would provide the required data regarding composition in the shortest possible time, as the (a + G) phase field narrows considerably at higher temperatures. The same work showed that the G phase ceased to exist between 580° and 595°C. A more precise estimate of the transformation temperature would therefore be obtained by annealing selected alloys at successively higher temperatures beginning at 580°C. EXPERIMENTAL PROCEDURE 1) Materials Used—The experimental alloys were prepared from four master alloys containing 15.00 w pct Cr, 15.28 wt pct Cr, 19.80 wt pct Mn, and 19.38 wt pct Mn which were made from super-purity aluminum, electrolytic chromium, and electrolytic manganese. The aluminum was of 99.996 pct purity, the principal impurities being copper, iron, and silicon. The chromium and manganese were 99.9 pct pure, the principal impurities being antimony, calcium, and magnesium. 2) Preparation of the Experimental Alloys—The alloys were prepared in 20-g quantities by melting together the requisite amounts of master alloy and aluminum in an alumina-lined crucible and, after thorough stirring with an alumina rod, cast into a cold copper mold to give ingots 1/4 in. in diam and 3 in. in length.

Jan 1, 1960

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital write-offs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral property possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulfur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. Present Value of a Mineral Property In essence the present value of a mineral property is a sum of money in today's dollars that future income from the property are worth. It differs from the total anticipated earnings by the amount of the interest that the unrecouped investment could be expected to earn during the period of recoupment. Thus, if one could accurately estimate what a mineral property will earn during its life, after deducting all operating, administrative, capital, interest, and tax charges, the determination of present value would be a relatively simple mathematical calculation. Normally, where the expected life of the mineral property extends beyond 20 or 25 years, the discounted value of earnings beyond this period is relatively small. The petroleum industry generally discounts the annual cash flow of an operation rather than earnings since, for tax-saving purposes, earnings are kept

Jan 1, 1976

By W. M. Weigel

Economic deposits of barite occur in Missouri in two main districts. The most important, the Southeastern or Washington County district, is in the southeastern part of the state, mostly in Washington County with a small extension into the northeastern part of St. Francois County. Roughly, it embraces nine townships or about 200,000 acres and accounts for from 80 to 90 per cent. of the state production. The Central district, is in the central part of the state, includes most of Morgan and Miller counties, and parts of Camden; Benton, Moniteau and Cole counties. The area embraced is much larger than the Washington County district, but the deposits are more infrequent. The location and general area covered by the two districts is shown in Fig. 1. There is another small area in southern Franklin County but so far its production has been of small consequence. It might be considered as a northward extension of the Washington County field. An, area in the central part of Hickory County has also produced a small amount. The outline of the districts as shown indicates the general area in which deposits have been found. The total area covered by deposits of barite is only a small part of this, as, in the Central district especially, there may be miles of supposedly barren areas between ore-bearing areas of an acre or two in extent. The date when barite was first mined in Missouri cannot be definit stated, but the industry probably dates back to about 1860. The occurrence of barite was known long before this, as it was encountered in the lead mines in Washington County and mentioned by several earlier writers." Missouri is reported as producing 8000 tons in 1882 so it is evident the industry was well under way in the seventies in order to have arrived at this substantial production. By 1893 Missouri production had increased so that it ranked with that of Virginia, then the largest producer it increased until in 1914 Missouri accounted for about 65 per cent. of the total United States output.

Jan 1, 1929

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By G. L. Schroeder

Investigations were conducted at two underground locations, foreman's room and 5702 area, of the Kermac Nuclear Fuels Corp. uranium mining installation, Ambrosia Lake, New Mexico. The rock environment is stratified sandstone. Pressures were varied from minus 0.4 an Hg to plus 3.8 cm Hg with respect to barometric pressure, and were maintained for periods ranging from several hours to 21 days. One cm Hg overpressure (-1.5% of normal barometric pressure) produced a 20-fold decrease in Rn flux into the foreman's room as compared to the Rn flux observed during dilution ventilation. The 5702 area experienced a 5-fold decrease in Rn flux for a similar overpressure. During 21 days of continuous 1 cm Hg overpressure in the 5702 area this reduced Rn flux was maintained. The smaller reduction in flux for the 5702 area results in part from the proximity of the foreman's room to a non-pressured area and the presence of an impermeable shale lens overlying the ceiling of the 5702 area. A 0.4 cm Hg underpressure of the 5702 area increased the Rn flux into the area by 3-fold over the non-pressured value. A barometric pressure influence on Rn flux into the mine and on air Rn concentrations in non-pressurd areas of the mine was measured. A falling barometric pressure causes an increase in the flux of interstitial gas into the mine; a rising barometric pressure decreases this flux. These effects are not seen in overpressured mine areas. Radon concentrations in rock interstices show, during overpressure, decreases of all locations monitored except in the immediate vicinity of the shale lens above the 5702 area ceiling. These reductions are the result of air flowing from the mine into the rock interstices under the influence of the pressure gradient induced by the overpressure. The relative humidity of the 5702 area was reduced after 2 days of 1 cm Hg overpressure from a pre-overpressure value of 96% to 81%. The control of harmful or noisesome gases which emanate into underground mining areas from surrounding rocks is often a costly necessity. In uranium (U) mines this problem is presented by the high interstitial concentrations of radon-222 (Rn), a radioactive noble gas of 3.82-day half-period, formed in the decay scheme of U238, and the relative ease with which this noble gas diffuses from its parent rock into the interstices of the rock and then to a working area. Long-term exposure to moderate concentrations of Rn (3000 µµc per 1) and its short-lived alpha-ray emitting daughter products, RaA (Po218) and RaC (po214), has been found to result in an increased incidence of bronchial carcinomaa2 The acceptable limit of Rn daughter products in a mine atmosphere is presently set at a concentration of short-lived radon daughters which would be in equilibrium with 100 ppc of Rn per 1 of air. Ventilation of mines is conventionally accomplished by continuously diluting the mine air with fresh air brought in by fan or natural convection from above ground surface. The diluted air is allowed to vent freely to the atmosphere. This process does nothing to retard the rate at which gases (including Rn) diffuse into the mine from surrounding rock. It merely reduces the concentrations of these gases within the mine. It is suggested that in a sufficiently permeable rock environment a slight pressurization of the mine air may induce air flow from the mine into the interstices of rock surrounding the mine. The convective flow of comparatively fresh air will reduce the concentration and the concentration gradient of undesirable gases in the rock interstices adjacent to the mine. Radon will diffuse counter-current to this convective flow at a rate proportional to its concentration gradient. In time, a steady state of convection and counter diffusion will be established. The Rn flux into the mine will never be reduced to zero, and will only asymptotically approach zero as the overpressure (and hence the convective velocity of purging air) approaches infinity. During 1963 and 1964, an investigation into the effect which such applied pressures have upon the Rn characteristics of a mine atmosphere was conducted at the Kermac Nuclear Fuels Corp. uranium mines, Ambrosia Lake (near Grants), New Mexico.

Jan 1, 1967

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955