Search Documents

By José Fagundes Junior, Cleudson dos Santos Rego, Bruno Bastos da Silva Murad, Vitor Borlot Borba

Since the startup in 2002, the Hot Strip Mill at ArcelorMittal Tubarão has increased gradually the coil output as the customers demand new and more resistant dimensionally challenging (thinner and/or wider) steel grades. As a critical feature for customer applications, improvements have been carried out aiming a higher thickness performance and reduction of internal losses while still meeting the more restrict tolerances booked by the customers. This paper presents the recent thickness performance evolution since 2017 and the main actions deployed to improve it.

Oct 1, 2019

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Juliano Braz Possatti, Arnaldo Carneiro Salles, Cleudson dos Santos Rego, Leandro de Lucas Mendes

The increase in customer demand for steels with higher surface requirements, associated with the need to increase ArcelorMittal Tubarão's HSM productivity, it was necessary the development of controls and actions to reduce scale losses within the scenario of high productivity. This article describes the path followed by the hot strip mill team in order to reduce the occurrence and severity of scales.

Oct 10, 2019

By Luiz Bruno de Oliveira Araujo, Luciano Morais Teixeira, Luiz Gustavo Pedrosa de Melo, Altair Lúcio de Souza

The off-line simulation of the metallurgical process in an industrial line brings several benefits such as: evaluation of the influence of the main parameters that affect the results of the process, comparison between different set ups, greater assertiveness in operational adjustments, process optimization and reduction tests for development of new products. With this objective, a software for offline simulation of the hot strip mill process of Gerdau Ouro Branco was developed based on the logic of calculations implemented in the online model. The software results in important process variables such as mill pass scale, load, torque, and power at each pass, temperature and the hot mean flow stress of the simulated material. During rolling mill process the strip presents different temperatures and time between passes for different points along the length, which directly influences the hot strength of the product and consequently in the calculated variables, thus the calculations executed by the software were divided to three points of the strip, head, body and tail bringing the individual results to each of these positions.

Oct 1, 2019

By Tiago Salzmann Vilela

No mercado de arames galvanizados destinados a indústria é exigida a uniformidade da camada de zinco sobre o arame. Neste trabalho, foram estudados os efeitos da velocidade de galvanização na uniformidade e espessura da camada de Zinco total, bem como a morfologia das fases de Zn e Ferro-Zinco sobre o substrato metálico. Verificou-se também o efeito do aquecimento após o processo de galvanização, observando o crescimento da camada intermetálica. Finalmente, serão mostradas as principais características de processo obtidas para garantir o atendimento aos ensaios de qualificação, em um estudo de caso de arames galvanizados produzidos em unidade industrial da Gerdau.

Jul 30, 2018

By Giulio Rodrigues Altoé

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of epoxy matrix composites reinforced with continuous fique fiber, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Aug 16, 2017

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Eduardo Vitral

The present study focuses in the simulation of pattern formation by ion beam sputtering on a material surface. This process is responsible for the appearance of unexpectedly organized patterns, such as ripples, nanodots and hexagonal arrays of nanoholes. A numerical analysis of preexisting patterns is proposed to investigate surface dynamics, based on a model derived from a Kuramoto-Sivashinsky anisotropic equation, in a two dimensional surface with periodic boundary conditions. While deterministic, its highly nonlinear character gives a rich range of results, making it possible to describe accurately different patterns. A finite-difference semi-implicit splitting scheme is employed on the discretization of the governing equation. Simulations were conducted with realistic coefficients related to physical parameters (anisotropies, beam orientation, diffusion). The study dealt with a random and a monomode 1D structure initial condition in order to understand how the shape and wavelength of the initial pattern evolve with time. Ripples and hexagonal patterns were observed in the results, being physically consistent with the phenomenon. Moreover, the Method of Manufactured Solution has been used as verification of the developed numerical scheme.

Aug 16, 2017

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Jefferson Lisboa Lelis, Marcos Roberto Soares da Silva, Maiara Rodrigues Gouveia

Nowadays, due the development of new hot rolled strips at USIMINAS, established the necessity of realizing studies to define new parameters for the welding machine of new pickling line, in order to improve mechanical and metallurgical properties of these materials. The aim of this study was to evaluate the weldability of high strength low-alloy steel with low boron content with tensile strength above 600MPa.The influence of energy input and preheating temperature on the mechanical properties of hot rolled strips were analyzed at three distinct thickness (2, 4 and 6 mm). To perform these evaluations were used tensile test, micro-hardness, metallography (micro and macro examination) and scanning electron microscopy analysis. In resume, a good welding performance was achieved, increasing preheating temperature and the welding energy higher than 60%.

Oct 13, 2019

By Mariana Macedo de Oliveira Lima, Pedro Emílio Gazola, Andrei Locatelli

Boron steel is used in the industry due to its great wear and impact resistance. During the hot rolling production of 15B29 steel flat bars it is a recurrent problem that the bars will present warping while on the cooling bed. Control this phenomenon is an opportunity to have better productivity, preventing metallic losses. Through the observation of the macro and microstructure samples produced with different reheating temperatures and cooling rates, it was found the presence of residual stresses and cracks on warped bars macrostructure. The residual stresses appearance suggest that the material cooling is too fast. Billets temperature on the reheating furnace of 1230°C reduced to 1100°C and the production pace slowed down. Bars temperature when arriving the cooling bed was reduced from higher than 670°C to 625°C. The results obtained made it possible to produce the material with better quality, reducing the warping effect at the cooling bed. The major influence on the materials warping was identified as the cooling rate at the cooling bed and the reheating furnace temperature was adjusted to provide a homogeneous temperature along the bars.

Oct 1, 2019

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By Bruno Kneipel Neto, Mylena Inaiê Correia, Fabricio Cerqueira, José Francisco da Silva Filho

The automotive industry, when aiming to increase the resistance to corrosion, uses in the Body in White (BIW) concept the galvanized steels. The hot-dip galvanized steels that stand out most are known as GI steels. They are formed by the zinc element and by phases of intermetallic intermediate iron-aluminum-zinc compounds. The characteristic properties of the GI coating are directly related to the formation of the intermetallic layer, which is responsible for providing the connection between the metal substrate and the coating layer. In this context, two different types of steel (SAE1005 and TRIP780 steel) were used for laboratory characterization of their intermetallic layers through metallographic techniques. The results of the tests showed that the inclined section metallographic inlay technique allows obtaining a larger region of analysis of the intermetallic layer. For the surface analysis, it was observed that the chemical solution used in the preparation of the samples was effective, making possible an analysis more specific about the intermetallic layer formation, distribution and morphology.

Oct 12, 2019

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Lidong Teng

ArcSaveTM is a new generation of electromagnetic stirrer (EMS) from ABB for electric arc furnace (EAF) operation. Its goal is to improve the safety, increase the productivity and reduce costs. Electromagnetic stirring in the melt bath during arc furnace operation will affect the scrap smelting, bath temperature distribution, refining reactions, and also the tapping practice. This paper has summarized the investigation results obtained from the first ArcSaveTM system installed in a 90 ton EBT arc furnace in USA. The hot test results show that ArcSaveTM has enhanced the heat and mass transfer in the arc furnace process. This results in a faster scrap melting rate, lower slag superheat during arcing, more homogenous melt bath, higher decarburization rate and higher EBT free opening frequency. ArcSaveTM has also reduced the tapping temperature and tapping oxygen in the steel. This brings a higher scrap yield and saves ferroalloy consumption in the downstream ladle furnace operation. The lower energy consumption, short tap-to-tap time, and consistent furnace operation bring increased productivity and safety.

Aug 16, 2017

By Francesco Toschi

The Special Bar Quality family comprises a wide range of steel grades, mainly requested by the automotive, energy and engineering sectors, for applications where significant performances are required (eg. stresses, temperatures, working cycles, etc.). To meet these requirements it is necessary to reach a precise control of both the mechanical characteristics and metallurgy structures along the whole production chain. For semi-product with large dimensions, such as equivalent diameters around 300 mm, this is traditionally obtained through a manufacturing route which comprises the casting in ingots followed by reheating, forging and rolling. After 2010, new processes were investigated and technologies developed to replace the ingot route with a continuous casting followed by controlled high-reduction rolling. In these processes a seamless integration of CCM with rolling is implemented so to obtain the precise control of material flow, applied deformation and working temperatures. By using the proper combination of rolling diameter, speed and applied reduction, a very good control of the metallurgy structure across the whole section can be obtained, so to also remove the internal discontinuities ("voids") generated during the continuous casting. These processes, which can be defined "forging-like", are applicable to several grades also with large semi-product dimensions (300 mm and more). Besides, removing the ingot route means increased yield and productivity, which is very beneficial to the economical management of the plant. An example of this "forging-like" process is represented by the high-reduction blooming stand installed by Acciaierie Venete in the Padova-Camin mill. This article describes its main concepts as well as its technology and process features.

Oct 30, 2017

By William Sergio Flores Roman

Los aceros para armaduras de hormigón tienen que exhibir una buena relación entre resistencia y tenacidad que se ve reflejado en la performance del producto en servicio al ser aplicado a esfuerzos exigidos. Acerbrag es una empresa que produce aceros para la industria de la construcción teniendo en su gama los aceros de medio carbono para la fabricación de barras conformadas de dureza natural para armaduras en estructuras de hormigón. El objetivo de este trabajo es encontrar criterios de ventanas de trabajos operacionales y de control para la manufactura de aceros con buenas propiedades mecánicas en términos de resistencia y tenacidad. Este paper muestra los resultados de los trabajos realizados en las diferentes áreas productivas para conseguir un producto final con mayor resistencia a altas exigencias en servicio, además, reporta diferentes aspectos del proceso de manufactura del producto que van desde el ajuste de la composición química del acero, incluyendo criterios de propiedades mecánicas objetivos, criterios de calidad interna mostrando la microestructura de la barra antes y después de los cambios y finalmente la calidad dimensional y superficial de la barra nervurada, este último potenciando la falla prematura del material. Todos estos cambios, se ven reflejados finalmente en la performance de la barra, sometida a los nuevos criterios de exigencia en los ensayos mecánicos.

Oct 30, 2017

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Rogério Martins Pereira, Charles Pierri de Souza, Lucas Gabriel Correa

The Tandem Cold Mill is composed by stands with rolls positioned so that the rolling force can be transmitted to the strip being processed. Due to the mechanical stresses inherent in the process, the roll bearings are heated and are equipped with lubrication and cooling systems. Nevertheless, there is the challenge of continuously monitoring the temperature of the bearings, which would allow preventive intervention in case of overheating. This paper presents an in-house solution to temperature measuring system applied to the backup roll bearings of a continuous Tandem Cold Mill. The system uses Zigbee technology and is integrated with the main control system, allowing early diagnosis of bearing heating and proper intervention. Results and features of the system are discussed.

Oct 1, 2019