Search Documents

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Edgar Ivan Castro Cedeño

En la producción de aceros limpios el control inclusionario es crítico para la obtención de un producto que cumpla con los requerimientos de calidad. El análisis de la distribución de tamaño de inclusión mediante modelos estadísticos permite estimar la incidencia de inclusiones en el producto solidificado a partir de mediciones tomadas en muestras relativamente pequeñas. En seis coladas de acero bajo carbono desoxidado con aluminio se tomaron muestras de acero a lo largo del procesamiento en horno olla y colada continua. Las muestras se prepararon para estimar mediante análisis metalográfico los tamaños de inclusión. Los datos de tamaño de inclusión se analizaron mediante modelos estadísticos de valores extremos, se hace una comparativa entre la distribución Gumbel (que forma parte de la norma ASTM E-2283) y la distribución Generalizada de Valores Extremos (GEV). Mediante una prueba de hipótesis con el estadístico Anderson-Darling, análisis de cuantiles y con la función de supervivencia se demuestra que la población inclusionaria se describe de una mejor manera con la distribución GEV. Finalmente se da un estimado de la incidencia probable de inclusiones en el producto solidificado.

Aug 16, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita de zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetaram a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução foi 85%, para 100% CO, 1373 K e 105 min, e 52%, para 50% CO, 1373 K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373 K durante 105 min.

Aug 16, 2017

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Jorge Madias

Durante la laminación de barras y alambrones para construcción civil; perfiles y ángulos estructurales y barras redondas y hexagonales de aceros de corte libre puede presentarse la apertura de la punta o la cola y el estallido central, con la consiguiente parada y caída de la productividad, y pérdida de rendimiento metálico. En este trabajo se analizan las diversas causas que confluyen para que este problema ocurra. Se analiza la influencia de posibles defectos en las palanquillas, las características del corte de las mismas y otros problemas de calidad. Se revisa el rol del precalentamiento previo a la laminación, la refrigeración de los cilindros, el diseño de pasadas y la respuesta del material en función de su ductilidad. Se presentan diversos casos industriales para ilustrar las diferentes razones detrás del problema de la apertura de punta.

Jul 30, 2018

By Álvaro Lúcio

This paper outlines the DPC process as na economic and environment friendly option for the use of cultivated forest as a source of raw material for metallurgical charcoal.The DPC process was specially developed to bring logistic, environmental, technical, economic and global energy efficiency when compared to termal1 the existing biomass carbonization process. The DPC process utilizes the volatile materials (condensable and non condensable) as a source of the energy required by the carbonization process guarantying its complete combustion. As result the DPC process avoids the burning of termal1 the loaded wood, obtaining a higher charcoal to biomass yield, and avoids the emission to the atmosphere of polluting gases. Gases emitted by the carbonizing wood have na energy termal1e enough to dry the wood soon after its harvesting. By avoiding the storage in the field during na average of 150 days, the resulting economy is quite significant. As a termal1e1 the higher charcoal to biomass yield na termal1e1e economy is obtained through the reduction of the cultivated forest term. This paper emphasizes the economic advantages of the DPC process.

Aug 16, 2017

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Marco Castenetto

Some of the most significant Danieli innovations in the field of long products are the: i) The EWR® system, through automatic continuous head-to-tail flash welding of billets at reheating furnace exit side, enables uninterrupted production of the mill for endless rolling of straight bars, wire rod and bar in coils. The process is particularly beneficial to wire rod and bar-in-coil mills as it enables production of “customized-size coils” (any coil weight according to specific Customer request) and with extra-high final coil weight, even starting from low-weight billets; ii) The Spooler process is based on twistfree winding of hot-rolled rebars into highly-compact/ultra-heavy coils featuring a unique cobble-free un-coiling capability. This enables high-speed feeding of the downstream cold-processing lines with hot-rolled spooled coils coming directly from the rolling mill without the need of any traditional off-line operation (such as de-coiling, stretching & re-winding). The system results highly beneficial both to bar-in-coil producers and to the downstream lines operators. The latest step forward is the combined application of these two systems that has made it possible for endless rolling of spooled bar in coils, enabling to cumulate the benefits of the two processes, particularly as far as transformation costs are concerned.

Aug 16, 2017

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017

By Karl Berger

Today we are talking about Industry 4.0, as the latest revolution of industrial processes and progress, considering that the steam engine (Industry 1.0), railways and cars, mass production in the 1920th (2.0), Industrial Automation (3.0), and finally integrated manufacturing, integrated communication, and internet (4.0) can be seen as the state-of-the-art situation in industry, nowadays. Similar to the Industry progress, we can approach the rolling process of material, which started about 150 years ago in a very basic way. Steam engine- and belt driven-mills were very operators’ intensive, brutal and risky to operate. Mechanical improvements brought throughput, safety and quantity, as also quality of the products. The rolling of steel, in particular of rails, beams, rebar, strip (focus in this paper) and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. From single stands to continuous rolling trains the production and quality of mills increased significantly. From ingots and blooms to slabs, we have to admit a big jump in which has changed the face of the world significantly. Thin Slab Rolling has revolutionized the output and the throughput of rolling mills (Generation 3.0 to 5.0). Finally, Endless Rolling, has boosted the quality and quantity of rolling mill processes and permitted nowadays to enter in market niches which were not thinkable a decade ago. Mastering the automation and applying reliable systems (mechanical and electronically) of drives, actuators and sensors, as also communication and information interchange to all levels of automation are the success factors of such complex mills, we call herein after “Rolling Mills of Generation 6.0”.

Aug 16, 2017

By Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Antônio Cezar Faria Vilela

A minor change in the chemical composition and temperature affects the slag viscosity, which has a great extent of the physical properties in regarding refining slags. Optimizing those parameters may affect the steel cleanliness. The viscosity measurement process is considered expensive, so the cost-effectiveness does not favor the measures at high-temperatures. Alternatively, it is possible to apply mathematical models or thermodynamic softwares to obtain viscosities for a given range of chemical composition and temperature of slags. The present work contemplates a validation of the experimental data, collected in the literature, with a calculated data and proposes an accurate representation of iso-viscosity curves applied for secondary steelmaking slags, covering the composition ranges: 0–100 wt.% CaO, 0–80 wt.% SiO2, 0–77 wt.% Al2O3 and 0–15 wt.% MgO (CSAM) system at 1500ºC. The viscosity representation fields include fully liquid and a partially liquid slags in the CSAM system and the viscosities were calculated using the FactSage 7.2 (for Liquid Phase) and the Roscoe-Einstein equation (for Phase mixture) for a total of 5976 slags. The preliminary results indicated that there is a great convergence between the calculated and experimental viscosities data, promoting an efficient approximation of the iso-viscosity curves for the CSAM slag system in the high-temperatures.

Nov 1, 2019

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Sihai Jiao, Xiaoming Xia, Bo Yan

Checkered plate, which is also known as floor plate, has a raised pattern that provides excellent skid resistance for a wide range of applications, such as flooring, walkways, platforms, stair treads, covers, etc. As one of most common products, carbon steel checkered plate is used in low strength with a large thickness margin for corrosion and costs a lot in corrosion resistance treatment and maintenance. Although austenitic stainless steel checkered plate meets the requirements of general corrosion resistance, it is also hard to provide a highly comprehensive performance for its low yield strength, which mean higher thickness, higher weight, lower stability of structure. Combined the advantages of stainless steel and carbon structural steel, a roll-bonded clad checkered plate with high performance in skid resistance, high strength and corrosion resistant is developed. The metallography shows metallurgically bonded interfaces. Both external and internal bending at room temperature can be done successfully done without any cracks. The yield strength is also significantly improved. Therefore, roll-bonded clad checkered plate is superior in microstructure, strength, ductility and workability. An application case on a pulverized coal injection platform in an iron-making plant, is also introduced to show the way of processing and installation. After two years of installation on the platform, the product still keeps the original appearance. It implies that the developed plate could keep the facilities functions with much less or no maintenance and make them much safer.

Oct 1, 2019

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Leonardo de Souza Melo, Giovani Rodrigues, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipment in 2015. In addition to improving productivity related to these new equipment, several additional jobs were planned and executed on equipment already installed has been carried out in order to improve the efficiency of the line. The present work exposes what was done in the scale breaker (tension leveler) to improve the availability results of the section and consequently of the line.

Oct 1, 2019

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017