Search Documents

By Arno C. Fieldner

Six years ago, I addressed the annual meeting of the American Society for Testing Materials on "Fuels of Today and Tomorrow."3/ Since then, our country has been drawn into another great war of veritably global extent, with unprecedented demands on fuels, foods, and materials in general. My purpose in this address is to review the changes in fuel supply and demand since 1937 and to give you my views on the outlook for the future. CONDITIONS IN. 1237 Daring 1936 the United States produced and consumed one-third of the world production of coal, two-thirds of the petroleum, and about 95 percent of the natural gas. Two-thirds of the oil produced in all countries since the discovery well was drilled in 1859 had come from American wells. With the exception of the three depression years 1931, 1932, and 1933, new oil reserves were being discovered since 1924 well in excess of our increasing rate of consumption. Discoveries of natural gas, likewise, were tremendous in volume, and this fuel was being transported to most parts of the country by pipe lines; some of them more than 1,000 miles long. We had all kinds of mineral fuels in abundance and at prices that did not stint anyone in the maximum utilization of the mechanical devices that were being developed on every hand. No one suspected that the time might come in a few years when, gasoline would be doled out to some of us at the rate of 1-1/2 gallons a week or that many of our fuel-oil furnaces would have to be converted to burn coal. Of course, these restrictions are due to unusual war conditions, such as lack of coastwise tanker transportation, unprecedented demand for aviation gasoline, and the shortage of rubber for automotive tires. However, these shortages do call our attention to the vital part of petroleum reserves in our country's future position among nations. Therefore, it is of special interest to review briefly the relations of recent supply and demand with respect to our various mineral fuels.

Jan 1, 1943

By R. F. Mehl, C. S. Barrett, A. H. Geisler

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

The following observations on the mineral composition of the lead-zinc ores at Captain's Flat, New South Wales, are based upon the examination of a collection of specimens made during a brief visit to the mine in January, 1942, in conjunction with earlier studies of specimens and mill products, which have 'been the subject of various Mineragraphic Reports, Captain's Flat is about 35 miles south of Canberra, and is connected with the main line from Goulburn to Bombala by a branch line to Bungendore, 23 miles away from the mine.The geology of the mine has been described by Kenny and Mulholland2 and by Harper.3 The country consists of Silurian sediments, which have been invaded by a composite sill of quartz-felspar-porphyry. Both sediments and sill have been folded gently, the axial lines of the folds trending north and south. In the vicinity of the orebodies the folds are steeper, and thru,st faults are associated with the anticlines. The intense compression and shearing that accompanied the faulting has converted the adjacent porphyry to schist. The Captain's Flat orebodies occur along such a zone of shearing and faulting, on the eastern limb of a steep, north-pitching anticline. At their southern end the orebodies are enclosed in the slates underlying the porphyry, but the northerly pitch of the fold carries the slate to greater depth in the northern part of the mine, where the orebody lies beween schistose porphyry on the hanging wall and massive porphyry in the footwall.THE OREBODIESThe orebodies occur along a N.-S. strike length of 4,200 ft., and from the point of view of mining, fall into three sections: the Elliot's Section to the north, the Central Section, and the Keating's Section to the south. The Keating's Section is separated from the Central Section by 500-600 ft. of mineralised ground of so low a grade as' to be called barren, and is offset about 125 ft. to the 'east of the Central body by an oblique fault striking N.300E. Elliot's Section and the Central Section are connected by persistent veins and stringers of lead-zinc ore, but although these are...

Jan 1, 1943

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By D. Harrington

Fire is always a serious-menace, whether in a residential or in an industrial region; in wartime it is particularly damaging in an industrial plant. The mining industry is especially vulnerable, as its plants are generally more or less isolated front centers of population and do not have access to modern fire-fighting equipment; moreover, owing to the transitory rapture of most mines, their surface structures; are often relatively flimsy and flammable.. Trained firemen seldom are available at or near mining plants to teach the fundamentals of fire-fighting to local fire brigades, with the result that efficiency in combating actual fires is lacking. Often the attitude "it can't happen here" is held by the management of a mining property, unless the plant has suffered a serious fire; even then lapse of time is very likely to induce forgetfulness as to the possible hazards. The necessity for producing metals for the prosecution of this war has increased management's responsibility. Whereas heretofore the loss of a plant or mill by fire meant merely monetary less to the stockholder of the company, now the national interest is affected, in that the nation suffers from loss of production of minerals indispensable for war purposes.

Jan 1, 1943

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

In a previous paper the writer dealt -with the jasper bar formations and their relationship to the structural geology of older pre-Cambrian rocks in the goldfields districts of Western Australia (24). He has pointed out in this ahd other papers that jasper bars, or banded iron formations, banded hematite or ,magnetite quartzites, jaspilites and related banded ferruginous or non-ferruginous cherts, occur in abundan'ce in the Older Greenstone Series of Western Australia (22), (24), (26). They are considered to represent special forms of banded ferruginous sediments, and are usually fpund in the field interbedded with more or less metamorphosed pasaltic 01' andesitic lavas and tuffs, now amphibolites, together with occasional thin bands of normal pelitic sediments, which go to make up a large proportion of the Older Greenstones in thfs State (26).Great thicknesses of fiat-bedded ]:landed ferruginous cherts are also found associated with cherty' carbonate rocks; quartzites, shales and thin-bedded dolomite whicIi constit'ute the Nullagine (Pl'oterozoic) system in the northwest of Western Australia. In the Hamersley Range district these banded ferruginous chert beds are the hosts of important deposits of blue amphibole asbestos.In the paper mentioned above brief reference was> made to the importance, of geological structure in relation to economic geology, particularly in the goldfields regions of Western Australia, and it was shown that jasper bars may have an important role in the study of 'the structural geology of many of these regions. Of possibly more immediate economic importance is the part that these rocks play, both directly and indirectly, as host rocks for mineral deposits-the chief of Which are gold, iron ores, blue asbestos, and manganese ores. The blue asbestos bearing banded iron formations mentioned above are confined to the younger pre-Cambrian Nullagine formations. They have been described in detail elsewhere (23). In this paper it is proposed to discuss the economic geology of the jasper bars found in the older pre-Cambrian series.The jasper 'bars have in themselves little or no intrinsic value except perhaps some of the more highly coloured and banded varieties which may be utilised for ornamental and decorative purposes. Probably the best known of such varieties is the so-called "marble bar;" a belt of, strikingly coloured banded chert occurring just south and west of the famous town of that name (see Fig. 1t). This consists of a hard, very fine, even-grained rock with alternate individual stripes varying from the thickness of a sheet of paper up to an inch or more in width, and ranging in colour from clear white to yellow, from various shades of pink to brilliant...

Jan 1, 1943

The method of investigation was to study the distribution of ore in great detail, to make a thorough structural study of the lode and the mine area, and then to compare the results of the two studies. Such a comparison usually reveals a very close relationship between geological structure and ore distribution, and can often lead to important conclusions which would not be reached in the ordinary working of a mine.The Triton mine lies 30 miles E.N.E. of Cue, or 380 miles N.W. of Kalgoorlie, in typical pre-Cambrian rocks, consisting of gTeenstone lavas and tuft's, interbedded with slates and some sediments, and intruded by granite and porphyry. Fig. 1 (at end of paper) is a longitudinal section of the mine and shows that the workings consist of the main North Emu and the smaller South Emu, separated by a distance of about 1 of a mile. Both orebodies occur on the same lode, which strikes north and south and dips practically vertically. On the same line, and of 1/2 a mile and a mile respectively to the north of the North Emu, are the small Rand and North Rand workings, where a big width of lode material has proved to be very low grade. In the North Emu the lode width averages 12 to 15 feet; it is seldom less than 5 feet and in places reaches 30 feet. In the South Emu the lode is wide, but only portion of it is payable.The lode is a mineralised bed occurring between massive lava flows on the east and a mixed series of tuft's and thin lava flows on the west. The lode material is hard, fine grained, and dark coloured, and generally has a faint banding which is believed to indicate a tuft'aceous origin of the original lode rock. Microscopic examination shows that the original lode rock has undergone considerable albitisation;' there has also been considerable formation of biotite which gives the lode material a characteristic sheen. The mineralisation consists of abundant fine pyrite, which is auriferous, and a lesser development of pyrrhotite which is, however, barren of gold.THE OREBODIES AND THEIR CHARACTERISTICSThe distribution of ore is best studied from gold contours, as these reveal features that cannot be detected in an ordinary assay section. Gold contours (see Fig. 3) are developed' by plotting the width and grade of all development and stoping assays throughout the mine on a longitudinal projection, representing each sample by a coloured dot according to a suitably chosen range of assay values, and then outlining areas of similarly coloured dots (see H. J. C. Conolly, Econ. Geol., April, 1936). Both width and grade must be taken into account and the simplest method of gold contouring is to use dwt.lft. values, but difficulties arise here with big widths of low grade and small widths of high grade ore. To choose an extreme case, 30 ft. of 2 dwts. and 2 ft. of 30 dwts. both equal 60 dwts.lft., and would therefore be given the same value in dwt.lft. contouring...

Jan 1, 1943

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the-indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer, or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made . . .

Jan 1, 1943

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted at the Bureau's Mount Weather Testing Adit, Mount Weathe, Va. The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Reveille, mining-ngineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gave valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

By H. F. Silliman, Daniel R. Hull, Earl W. Palmer

THE brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that [ ] contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6 ¾ in. wide by 1 in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. [ ] In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breaking rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause-however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

6784. Barnes, V. L., and Romberg, Frederick. Gravity and Magnetic Observations on Iron Mountain Magnetite Deposit, Llano County, Tex. Geophysics, Menasha, Wis., vol. 8, No. 1, 1943, pp. 32-45. An outcrop of magnetite in the Central Mineral region of Texas is explored experimentally with a dip needle and a gravity meter. Two anomalies are observed, one due to the outcropping body and one probably due to a previously unknown body close to the outcrop. The possible attitudes of the bodies are discussed, and their masses and probable dimensions are computed from the gravitational observations. - Author's abstract.

Jan 1, 1943

By Nathan C. Rockwood

THE title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. DEFINITION OF MINERAL AGGREGATES "Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without portland cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. Mineral aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theoretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. EXPLORATION AND POSSIBILITIES OF DEVELOPMENT The distribution of deposits of mineral aggregate is universal, since almost any part of the earth's crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (1) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engineering talent in its operating branch, but it lacks, to a considerable

Jan 1, 1943

By Edwards A. B

Renison Bell is on the Emu Bay Railway, midway between Zeehan and Rosebery on the west coast of Tasmania. The tin deposits in this area have been described by G. A. WaIler (1902), L. K. Ward (1909), H. Hermani (1914), and Hartwell Conder (1918), for the Tasmanian Geological Survey. The ore-bodies occur in the slates, grits, altered lava flows and tufts of the Dundas Series, and consist of fine-grained cassiterite disseminated through massive sulphides (chiefly pyrrhotite or pyrite), or through bodies of quartz and sulphides. Some of these bodies show a N.W.-S.E. strike, parallel to the strike of the tin belt, but others strike N.E.-S;W. or E.-W.The ore-bodies are of two types: (1) steeply dipping fissure veins,' spoken of locally as "feeders," and (2) flatter-lying bodies more or less conformable with the bedding planes of the slates (bedded veins), spoken of locally as "floors."The feeders range from 5-12 ft. in width, with occasional bulges as great as 4q ft. Their lengths vary from 100 ft. to several hundred yards, and they are known to continue to Clmsiderable depths. 'They dip steeply, generally at angles of 45° to 60° to the east or south.The floors, where they occur, 'are directly connected with the feeders, and are sheet-iike bodies of sulphide ore. The composite ore-bodies thus have the shape of an inverted L, or a T, according to whether 'the floor extends out from one side or both sides of the feeder. Most of the floors extend from the hanging-wall side of the feeder. Where erosion has removed the connection, they appear as separate bodies.The feeders as a rule carry more quartz and arsenopyrite than the floors, and are richer in tin. In addition, the cassiterite tends to be coarser grained in the feeders than in the floors. The floors, on the other hand, carry a greater proportion of -sulphides, chiefly pyrrhotite, and the grade of ore and grain size of the cas,siterite tend to decrease as the floor is followed down the dip away from the feeder, so that the outer and lower extremities of the floors may be too low-grade to work economically. The average grade of the ore worked at present is 0·9,0/0 tin. The slates forming the roofs of the floors are commonly much contorted and silicified,' so that they form hard rocks in which the contortion and shattering of the original slates are well preserved. Joints extending upwards, more or less at right angles to the roof of the floor, are occasionally filled with finely crystalline quartz, similar to that in the orebodies, and are often rich in tin, so much so that the slate as a whole may average 0·4% tin.Some carbonate gangue is present in all of the ore-bodies, commonly on the footwall side, and, in places it becomes an important constituent...

Jan 1, 1943

By D. S. Kingery

Recent Federal coal-mine inspections have revealed some good and some definitely hazardous practices and systems for transporting; handling, and storing lubricants in and about coal mines. Improper storage or handling of. lubricants in coal mines has caused disastrous mine fires or, by supporting combustion, has made fires from other sources more difficult to fight. Careless handling of grease and oil around electrical equipment wastes much oil and permits entrance of grit and foreign substances into the working parts, which causes excessive wear and increases the possibility, of electrical ignition.

Jan 1, 1943

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted the Bureau's Mount 'Weather Testing Adit,Mount Weather, The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Revelle, mining-engineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gavel valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By Anton Gronningsater

AT the present time we hear a great deal about organization of labour, collective bargaining, workmen's councils, and company unions; about C.1.0. with its principle of vertical unions and A.F.L., largely based on craft unions; and about provincial and federal laws for protection of labour's right to collective bargaining. What we perhaps hear too little about is corresponding organization of the employers, although it recently is mentioned more frequently. I will only mention W. H. Davis, Chairman of the United States War Labour Board, who has had and is having plenty of experience in this field and has also studied labour conditions in Europe-in Sweden for instance. He has repeatedly expressed the opinion that where employer-employee problems are involved, a thing badly needed in America is organization of employers as well as employees to get some order in the present chaos. With this I agree. I believe a strong organization on one side necessitates a correspondingly strong organization on the other side; that has at least been the experience in the industrialized countries in Europe. I happen to be fairly familiar with conditions in Norway, where they have struggled with these problems for fifty years, and a talk on the history, development, and present state of employer-employee relations in that country might perhaps be of interest as giving a general picture of the development of such relations in the northwestern European countries as a whole. The talk was originally given to the Fourth Year students in Mining and Metallurgy at the University of Toronto. I have changed it somewhat to fit a different audience, but I hope you will make allowances if you now and then are reminded of the school auditorium. I will try to be as objective and factual as possible, but it is probably unavoidable that some of what is said is coloured by personal opinion.

Jan 1, 1943

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By George C. Bateman

WHAT I would like to do is to talk for a while tonight about the Canadian mining industry in wartime-at least, the Canadian mining industry as viewed through the eyes of the Metals Controller. There is nothing quite like the Canadian system in the system of controls in the United States, because the Canadian Controller combines the functions of a good many of the organizations here. I think the nearest counterpart would be the Divisional Chiefs of the WPB-although they have perhaps less authority and operate in a somewhat narrower field. My own field, as you know, is the metals and minerals-all of them, as a matter of fact, with the exception of steel and iron and coal and oil. And as I am responsible for supplies not only from domestic sources but also from foreign sources, I exercise most of the functions of the WPB and some of the functions of the Board of Economic Warfare. As my department is also responsible for stock-piling and for the financing of new operations, I therefore exercise some of the functions of the Metals Reserve and also of the Defense Plants Corporation. Being an administrator under the Wartime Prices and Trade Board, I also have the same function in relation w the price of metals as the OP A. The Canadian system of controls is compact, relatively simple, and I believe reasonably efficient. I think two of the reasons for that are that both the Controllers and the Directors of production are clothed with very wide authority, and also the fact that all the buying for the three arms of the service is done through the Department of Munitions and Supply, of which we are a part.

Jan 1, 1943