Search Documents

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By L. Hartsell Cash

INTRODUCTION Created in 1944 to help rebuild those economies, principally in Europe, which were seriously damaged or destroyed during the Second World War, the World Bank--or to use its correct name, the International Bank for Reconstruction and Development-began its operational phase by making a loan to the Government of France to accomplish two tasks: (i) to import coal for space heating purposes; and (ii) to buy new machinery and equipment to help rehabilitate its coal mines. Once the thrust of reconstruction in postwar Europe was largely accomplished, the World Bank Group (for today the World Bank has three separate lending windows) turned to mobilizing funds to improve living standards in developing countries, which remains its primary goal today. Over this period of time, the World Bank Group has continued to assist the world mining industry in various ways and, since 1955 the World Bank Group has financed mining or mineral processing projects with loans/credits totalling $1.5 billion. The World Bank Group consists of two institutions--the World Bank itself and the International Finance Corporation (IFC), which was founded as a separate institution in 1956 and three separate lending windows--the World Bank, the International Development Association (IDA), and IFC. The World Bank loans are provided at commercially-related interest rates but have grace periods usually of up to 3 to 5 years and repayment periods ranging from around 15 to 20 years. Since the World Bank raises its operating funds on the international capital markets in varying currencies and in varying interest rates, it relends a basket of currencies at floating interest rates which are fixed every six months to reflect the Bank's own borrowing cost. At the present time, the interest rate is just below 10% per year and in addition, a one-time front-end fee of 1/4 of 1% is charged. Also, a commitment fee of 3/4% per year is charged on the undisbursed amount of the loan itself. For loans to industrial and mining projects, it is normal to charge an additional guarantee fee of 1 to 1.5% in addition to the annual interest rate. This guarantee fee is payable to the government of the country in which the project is carried out since, by its charter, the World Bank is required to have the guarantee of the host government for each loan made in a specific country. By far the greatest source of lending funds within the World Bank Group is that of the World Bank itself and for the fiscal year ending June 30, 1984, the World Bank approved loans totalling $12 billion. The second lending window within the World Bank Group is IDA which performs the same functions as the Bank itself and has the same staff. Nevertheless, its loans (called credits) are made on much softer terms and are made to the poorest nations only. IDA funds are subscribed by the wealthier countries, usually as grants, and these are relent as credits to those countries with the lowest per capita income. IDA credits are made for 50 year periods, including 10 years of grace, to the government itself. The credits are interest free, but there is a service charge of 3/4% per year on the amount withdrawn and outstanding to defray the administrative costs of IDA. Credits approved during fiscal 1984 totalled $3.5 billion. The third lending window is IFC. While IFC is a separate corporation and operates quite separately from the World Bank and has its own staff and regulations, it works very closely with the World Bank on its overall approach to the mining sector and to a particular country. IFC's mission is essentially to supply venture capital and to stimulate development of the local private sector in capital markets as well as to promote the international flow of private capital to developing countries. Unlike the World Bank and IDA, the IFC does not lend directly to governments

Jan 1, 1985

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

Andy H. Vassiliou – Introduction Ladies and gentlemen,.good evening and welcome to the Paul F. Kerr Memorial Symposium dinner. I believe we are all here to honor the memory of a great teacher and advisor, and a true friend -- Professor Kerr, or Dr. Kerr, or to most of us who were his students, "Pappy" Kerr. Most of us who attended the Paul F. Kerr Memorial Symposium earlier today at the New York Hilton had the opportunity to read, or listen to, or discuss scientific papers presented in honor of Dr. Kerr. In addition, all of the speakers had the opportunity to reminisce about their association with Dr. Kerr, who was credited as having contributed substantially to their graduate education and the development of their careers. Dr. Kerr's two daughters -- Ruth and Nancy -- who attended the Symposium at the Hilton are also here with us tonight. I think we should keep tonight's festivities on an informal basis since we are all old friends or former students of Dr. Kerr. Some of us may want to say a few words about our experiences at the time we were students at Columbia, and hopefully include some anecdotes relating to Professor Kerr. I would like to invite everyone to do so, but first we have arranged for two of us to be the lead speakers, whom I will introduce in a few moments.

Jan 1, 1985

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon's economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country's only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon's gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon's ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985

The Morley Coal Measures (Upper Cretaceous) at Ohai Coalfield were deposited in an intermontane basin alluvial environment of entirely terrestrial aspect. Within this regional setting, three distinct types of depositional environment are recognised; these are: (i) a sand-dominated (South Saskatchewan type) braided river system characterized by channel-bed dunes and possibly compound bars; (ii) a well-drained floodplain environment frequently subject to crevasse-splay and overbank-flow sedimentation; and (iii) a poorly-drained, commonly peat-accumulating backswamp environment locally traversed by tributary drainage systems and occasionally inundated by crevasse splays and overbank flows. All major coal seams of the Morley Coal Measures originated within forest moors under predominantly telmatic (periodically inundated) conditions. The peat-forming vegetation comprised largely arborescent forms (dominantly conifers), in addition to pteridophytes and bryophytes. In-seam vertical variations in coal type indicate groundwater levels initially decreased and then increased during the lifetime of a particular peat swamp, possibly in response to a change in the migration direction of an adjacent fluvial system. The proposed depositional model for the Morley Coal Measures has the potential to be utilised during exploration programmes and mine development to impart greater objectivity to predictions concerning seam geometry and continuity, trends in coal type and quality, and likely roof and floor conditions.

Jan 1, 1985

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By Budiselic C, Hefter G

The uptake of gold by activated carbon from acid chloride solutions involves the reduction of gold(IIl) to metallic gold. Deposition occurs only on the surface of the carbon at localized active sites at first, and subsequently at less active areas. The rate of uptake depends on the surface area of activated carbon, which confirms results from a recently published study (de Siegel and Soto, 1984). Increased rates of uptake were observed at higher temperatures and lower chloride concentrations due to the decreased stability of AuCI4-, the major gold(IIl) species present. Recoveries of gold approached 100 per cent for a contact time of 60 minutes at 20°C in a well stirred solution initially 5 ppm in gold(III) and containing 0.5 per cent w/v coconut-shell carbon. The presence of 0.25 Mnitric acid or 100 ppm iron(IIl) had no detectable effect on either rate or efficiency of gold uptake.

Jan 1, 1985

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By R. W. Lawrence

"Biological leaching can be used to enhance the recovery of gold and silver from refractory ores, concentrates and tailings. The method liberates precious metals associated with sulphide minerals such as pyrite and arsenopyrite making them amenable to cyanidation. The chemistry and features of biological preoxidation leaching is discussed. A summary of the results obtained on various ores, concentrates and tailings is presented.INTRODUCTIONRefractory precious metal ores in which gold and silver are finely disseminated in sulphide minerals such as pyrite and arsenopyrite are becoming more important to the mining industry. This is due both to a depletion of simpler, free-milling ores and to a significant increase in the price of gold in recent years. Whereas many ores can be directly cyanided with gold solubilizations over 90% obtained, the refractory ores respond poorly to direct cyanidation and require decomposition of the precious metal-bearing sulphide minerals to increase recoveries.Decomposition of sulphides by oxidation prior to cyanidation can be carried out by several means. The oldest method is roasting which removes unwanted ore constituents by high temperature oxidation and volatilization. In Canada, for example, roasting is used at Giant Yellowknife (Connell and Cross, 1981). Another method gaining increasing acceptance is pressure hydrometallurgy which uses aqueous oxidation conducted at high temperature and pressure. Homestake Mining Company have recently completed construction of a plant incorporating pressure oxidation at their Mclaughlin property in California (Guinivire, 1984)."

Jan 1, 1985

By Lucia Kuizon

The Pinnacles Wilderness Contiguous Wilderness Study Area (WSA) (CA-040-303) is 30 miles south of Hollister, CA, in San Benito and Monterey Counties. It is composed of five parcels of public land totaling 5,838 acres adjacent to the Pinnacles National Monument. The U.S. Bureau of Land Management later reduced the size of the Recommended Suitable Area (RSA) to 2,200 acres. U.S: Bureau of Mines personnel examined the entire WSA in May 1984. The WSA is underlain by Tertiary sedimentary and Cretaceous plutonic rocks. Diatoms occur in interbedded tuff, shale, and sandstones in the northern part of the WSA, but outside the RSA. In 1984, there were no mines, prospects, mining claims, leases, or mineral resources in or within one mile of the study area. No energy minerals were identified; however, an oil well was drilled in 1951 in the northern part of the WSA, but outside the RSA; it was a dry hole.

Jan 1, 1985

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

By H. P. Cole

Methods for increasing compliance to medical and health regimens were reviewed along with similar research in industrial and mine safety. Principles abstracted from both areas suggest that compliance with health and safety practices is improved when: (1) Workers are cooperatively involved with management in setting safety goals and planning for their achievement, (2) the program has the support of workers, supervisors, and management, (3) specific tasks responsible for injuries are targeted, (4) company organizational policy, educational, and behavioral programs work together toward the same goals, (5) workers and supervisors are frequently informed about their degree of correct task performance, and (6) programs are monitored by the frequency of correct performance of targeted tasks, (the means to lowered accident rates) rather than by lowered accident and injury rates themselves (the goals for safety programs.) Safety programs that incorporate these principles increase persons' adherence to specified health and safety practices and subsequently decrease injury rates. It is recommended that: (1) a group of experts be convened to study the application of these principles to coal mine safety programs, and (2) a short course for safety trainers be developed to demonstrate how these principles can be used to strengthen existing mine safety programs.

Jan 1, 1985

By David J. Hoadley

This report describes the development and limited testing of a semi-automatic, raise climber, Compact Service Hoist System designed for stope access in underground metal and nonmetal mines. Demonstrated capabilities of the system include a 1,000-lb payload capacity, control from the traveling cage and from up to three remote stations, operating in vertical or inclined raises 3 ft in diameter and up to 300 ft in length and a travel speed of 50 ft/min. The system has the capability of operating in crooked raises because the conveyance climbs two stationary wire ropes suspended down the raise. The drive unit is electrically powered with power and control signals supplied to the drive unit through an umbilical 'cable also suspended down the raise. The system has been designed for portability, ease of installation and minimum raise development. The hoist has been demonstrated successfully in an above ground test tower. This report provides a detailed description of the hoist design and its demonstrated performance to date.

Jan 1, 1985

By Robert S. Schechter

A minitest of the new potassium chloride-potassium carbonate two-stage in-situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing cation-exchange reactions. The test also indicates permeability anisotropy and the existence of disturbed flow fields.

Jan 1, 1985

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990's new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985