Search Documents

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By R. F. Lynch, F. E. Goodwin, A. F. Skenazi

"The Gal/an alloy has been developed for continuous galvanizing of steel. The choice of the eutectic zinc-aluminum alloy with addition of misch metal gives a coating with specific characteristics as far as structure, analysis, surface chemistry and surface morphology are concerned. The performance of the uncoated Galfan coating is superior when compared to conventional galvanized particularly for corrosion resistance and ductility. For coil coating applications, these two assets are of the utmost importance but in order to benefit from these two advantages, good paint adherence and high resistance to edge creep and blistering have to be obtained. Despite Galfan's unique features compared to other zinc based or aluminum zinc based coatings, existing pretreatments and painting conditions are used with only minor modifications in order to assure good adherence and edge creep resistance. With compatible processing, Galfan can outperform galvanized and Galvalume as a substrate for coil coating as is demonstrated with various test results.IntroductionThe technical and commercial development of Galfan, a 95% zinc-5% aluminum-0.1% lanthanum-cerium hot-dip coating for steel, has been rapid. From its identification as a promising coating in late 1980, it has evolved from a research product to a fully commercial product with over 100 000 metric tons of coated sheet produced to date, and another 90 000 tons, at minimum, scheduled for 1986. The great majority of tonnage produced to date has been coil coated for use in building panel , appliance, and similar applications. Much technical work has been done to determine the suitability of Galfan for these applications and the proper way of processing sheet for best results. The present state of knowledge is discussed in this paper, along with some recent applications which are given asexamples"

Jan 1, 1987

In 1556, Agricola noted that "a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him"(1). In today's world, the owner rarely has the opportunity to visit the mine and, instead of reading about the `nature of the vein' in annual reports, prospectuses, government publications, et cetera he sees the words `reserves' and `resources'. Unfortunately, the subject of reserves and resources has become increasingly complex and Canadians, along with their counterparts in Australia and elsewhere, are still struggling with definitions which will attempt to cover all conceivable circumstances from national or regional resource endowment to the material to be extracted next week from a given stope or open pit bench. The providers and recipients of reserve and resource data are: - Government agencies who are concerned with questions of national endowment, strategic use of raw materials and other questions of public policy. - Stockholders who have a vested interest in the basic assets of their companies. - Financiers who are concerned about the security of their loans. - Regulatory bodies whose function is to protect a frequently naive investor from unscrupulous practices. - Management, at head office and on-site, who need basic information for decision-making, whether it be to open up a new mine, expand or close an existing operation, acquire or merge with other entities, or, more mundanely, for routine mine planning. To satisfy their demands with unanimously accepted definitions is a formidable task but, it is my impression that, little by little, a concensus appears to be growing within the industry.

Jan 1, 1987

By Joan Weinberg

The real gross national product (GNP) expanded by 2.3% during the second quarter, down from the anomalous 4.4% growth rate in the previous 3 months. If the expansion continues through October, it will have lasted 5 yr and become the second longest in 40 yr.2 As in the first quarter, improvement in U.S. exports played a role in the continuing--albeit slow--growth. More than 2 yr of declines in the dollar relative to currencies of other industrial countries have contributed to a slight reduction in the trade deficit in real (volume) terms, as real net exports of goods and services rose $1.9 billion (table 1). Exports grew a strong 12.1% while imports, which had fallen the previous two quarters, rose 7.4%. Manufactured goods and petroleum products accounted for most of the second quarter import increase. The American Petroleum Institute estimates that the volume of crude oil and refined products imports in the first half of 1987 surpassed those in the same period last year by 7.5%, reflecting falling domestic production and higher than expected demand. Expenditure on durable goods--those that last at least 3 yr-by both consumers and producers also contributed to the second quarter expansion. Personal consumption of durable goods rose 9.0%, after having fallen the two previous quarters. Motor vehicle purchases accounted for most of the second quarter increase and the first quarter decrease. Sales of automobiles surged in the last quarter of 1986, as consumers rushed to capture the sales tax deduction that was eliminated on January 1. Sales fell in the first quarter of 1987, but have now moved closer to the trend line exhibited in the first three quarters of 1986. Automobiles accounted for half the 0.8% July gain in retail sales, and two-thirds of the 1.4% June gain. Producers durable equipment purchases also rose this quarter, accounting for the increase in nonresidential fixed investment.

Jan 1, 1987

By Ronald T. Mayerle

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 20,500-acre part of the 104,085-acre Rincon Wilderness Study Area (OR-002-082) in order to evaluate its identified mineral resources. The wilderness study area is located in Harney County, OR, about 12 miles west from Fields. No mineral resources were identified within the study area. A literature search found no records of mining or minerals exploration, nor did a ground search find any evidence of mining-related activity. Of seven alluvial samples taken from the major drainages of the study area, all were barren except one. This sample, taken from a dry streambed along the southern boundary, contained $0.07 gold per cubic yard; however, this small amount of gold is of no economic significance, and the source is probably outside the study area. The Pueblo-Steens mining district extends to within 4 miles east of the study area. No evidence of geological environments similar to those that were responsible for the formation of resources or occurrences of metals and nonmetals within the district is known within the study area.

Jan 1, 1987

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By Robert Keyes, Charle Knowles, Glenn Kendall, Gary Fletcher

"The metal mining industry in Canada has been dramatically affected by the changes that have occurred in the world mineral market place. World economic restructuring in the post ""oil shock"" period of the mid-1970s, greatly increased competition from suppliers in the developing countries, and commodity price and currency pressures have all combined to severely test Canadian competitiveness. In the new mining world, the rate of growth of demand for metals has declined due to product downsizing, materials substitution, and a relatively slower growth of over-all world economic activity.The interplay of market and political factors is complex. Canadian metal mining companies must compete in world markets against low-cost producers in developing nations whose priorities often appear to be centred on maximizing foreign exchange earnings to foster development goals and debt repayment. Many of these countries have high levels of government intervention in their mining industries. The result is a greatly in-creased number of suppliers all vying for a share of a world demand growing at a relatively slower rate than in the past. To be able to compete under these circumstances, Canadian companies have had to undertake 'survival mode' measures and look to new ways of doing things. In order to identify the effects that the recent market and economic trends have had on the Canadian metal mining industry, a study was undertaken by Canada Employment and Immigration to assess these changes and their implications for the metal mining workforce.The Canadian Occupational Projection System (COPS)—Sector Study Group with the cooperation of the Mining Association of Canada, undertook a human resource survey to gather current employment and occupation information. This formed an important part of the Canadian Occupational Projection System Metal Mining Sector Study. This article addresses the with survey results, a C.E.I.C. worker mobility study, and trends and issues that are changing the mix of jobs and the way they are being done.Figure 1 shows metal mining employment for the period from 1974 to 1984. It provides a clear picture of the employment swings that the industry has experienced especially during the recession period of 1981 to 1983. From 1981 to 1983, employment dropped by 14 000, from 68 000 to 54 764, and then dropped to its lowest point in 1984 of 52 783. We feel that employment in the medium term will be flat with growth in gold mines being largely offset by continued workforce rationalizing in other sectors.Perhaps the key point is that equivalent levels of output have been achieved in the recent period (1981-1984) with a workforce that is 25% smaller than it was in 1974. This also raises the questions which the COPS/MAC survey and COPS mobility study sought to clarify, namely, what jobs have been cut and where have these people gone? Equally important are the questions of occupational skill level changes, and what types of jobs are declining and which ones are becoming increasingly important, as economic and technological changes have altered the mining work place."

Jan 1, 1987

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By B. J. Moore

This publication contains analyses arid related source data for 274 natural gas samples from 20 States. Of the total samples, 269 were collected during calendar year 1985; the reminder were collected earlier, but releases granting permission to publish were not received before 1986, All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1987

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By David K. Ingram

The Bureau of Mines conducted underground mapping and rock strength tests to describe and analyze mine roof conditions surrounding ancient stream channel deposits (paleochannels) in the Pittsburgh Coalbed in southwestern Pennsylvania. Paleochannels in the study mine consist of sandstone and/or siltstone and affect the Pittsburgh Coalbed through erosion and/or differential compaction. Differentially compacted sediments within and adjacent to channel deposits caused slip planes, faults, clay-dike faults, clastic dikes (clay veins), coalbed rolls, and slumped structures. Paleochannels can be predicted by recognizing these features and associated sediments, which allows for modification of long-and short-term mine planning and development. Mine entries located beneath the paleochannel deposits exhibit less stable roof conditions than entries with normal (nonchannel) roof. Paleochannel deposits comprise only one-fourth of the mapped study area; however, they contain one-half of the hazardous roof. This study deter-mined that rock strength evaluations, including rock quality designation (RQD), unconfined uniaxial compressive strength testing, and point-load testing, must be accompanied by underground observations. Suggested remedial support techniques include angled and/or longer tensioned bolts, steel mats or crossbars, steel sets or cribbing, and roof trusses.

Jan 1, 1987

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987

By A. E. Taylor, A. S. Judge, P. T. Lafleche

"Resource development in northern Canada has special requirements which derive from the unique environmental and eco-logical nature of the northern environment. In this paper several case histories in which the Permafrost Research Section of the Geological Survey of Canada (GSC) has participated are used to illustrate how geophysical methods may be used to address some of these considerations. Although some of these examples were developed while examining problems directly related to oil and gas development and transport in frontier regions, such or similar methods also have application to mining problems.IntroductionA critical parameter is the distribution and thickness of permafrost, which in northern Canada varies from being a few metres and discontinuous at the southern limit to thicknesses in excess of 700 m in the Arctic Islands'!'. Figure I is a schematic diagram of typical ground thermal conditions in a permafrost zone. The upper zone is defined by an active layer which undergoes a seasonal freeze/thaw cycle. In the simplest case, the ground remains permanently frozen below the active layer to the depth of the O°C isotherm, which is defined as the base of the permafrost. Water chemistry, pore structure and pore or grain size may cause the base of the frozen ground to be above the permafrost by up to 100 m(2). Ice can be found within the permafrost in the pores of solid rock or sediments, as massive ice within unconsolidated sediments or as ice lenses within fissures in a solid rock mass. The mining technique used in these conditions, whether open pit or underground, can differ considerably from that used in southern Canada. In the high Arctic, for instance, the dry drift method is feasible underground in the permanently frozen host rock. The frozen nature of the wall rocks can obviate water-related problems."

Jan 1, 1987

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By M. J. Hart

Today, aggregate producers in the Denver Metropolitan area, herein defined as Denver and surrounding communities in Adams, Arapahoe, Boulder, Douglas and Jefferson Counties, are scrambling to secure their future reserves. The Denver market is somewhat unique among the larger metropolitan markets in that the source of needed aggregate for the future is very much undecided. 2. Present Aggregate Resources Presently, the annual consumption of aggregate resources in the Denver Metropolitan area amounts to approximately 16 million tons of sand, gravel and crushed stone of which the later accounts for about 20%. Based on population growth projections for the front range, by the year 2000 the annual rate of consumption for aggregate in the Denver Metro area could be in the 25+ million ton range.

Jan 1, 1987

By O. P. Garg

"The Iron Ore Company of Canada (IOC) operations in Labrador and Quebec, in Canada, is among the largest openpit mining complexes on a world wide basis. Since the 1981-82 recession, IOC has embarked on a comprehensive cost reduction and productivity improvement program in order to survive in the world iron ore market.This paper will outline the approach used in prioritizing the cost reduction items.IntroductionMuch of the mining industry in North America is in a crisis state. Most producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC) operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectively. A company owned and operated railway links this operation with the dock terminal facilities in Sept-Iles, Quebec.In the past decade the Iron Ore Company of Canada has been one of the largest producers of iron ore products in the world. Its pellets and concentrates as well as natural ores were sold in North America, Europe and the Far East. In 1981-82, sales, particularly in North America, went into a serious decline. For almost 30 years, the gospel IOC preached to employees was ""production, production!"" There were many innovations, and millions of dollars were spent on the biggest and best equipment, on research and development, on training and developing employees."

Jan 1, 1987

By K. Fountain

In Novemeber of last year I visited a mica mine in Hunan Province, China. For nine months , we had been trying to sell Chinese mica to a customer in Belgium. Talking to the customer was like negotitating with a stone wall. The buyer refused to communicate any -thing other than his steadfast refusal to consider Chinese mica. He would not advise us what he wanted, what specifications or grades. He would give no indication if our price at market, or reasonable, or totally out to lunch. He would not even accept samples. It took no genius to guess that the mica buyer had at some time in the past bought a shipment of Chinese mica and had received a disaster. I invited the mica mine in Hunan in order to see for myself what could be done - without massive investment in equipment and instruments - to upgrade the quality of the mica for export. We had seen this type of customer reaction before. One disgruntled customer who had pur¬chased pigment grade barites direct from China ranted and raved about unreliable and inconsistent quality. It did no good to explain to him that China is a big country, with hundreds of mines scattered throughout many areas, each producing a different product. Our further explanation that Chinese export organizations also varied in degree and efficiency of customer service fell on deaf ears. Samples had no effect on his perception. Eventually we showed him photoraphs of two mountains of pigment grade barites. One lot was our sales of pigment barites to a major European minerals processor. Our Chinese barites stood proudly white and beautiful next to a hill of other material which now appeared at best mediocre and dull by comparison, and which the buyer had decided to reject after he received our Chinese barites. Finally the customer was sufficiently impressed to look seriously at our guaranteed specification and the outturn analysis performed by our other customer.

Jan 1, 1987