Search Documents

By Zhi-biao Yin

Copper smelter flue dusts often cannot be directly recycled to the smelting process and accumulate as hazardous wastes requiring environmentally acceptable disposal. Because of the limited amount of flue dust, a separate copper extraction process must be simple and require-a small plant investment. A flue dust process has been developed, consisting of the following steps: (1) roasting a pelletized mixture of hydrated lime and flue dust to fix arsenic and sulfur as insoluble calcium salts, (2) heap leaching the roasted pellets with a buffered ammonia/ammonium salt solution to extract copper as an ammine complex in a lined cell that is the final repository of the leached pellets, and (3) boiling ammonia from the lixiviant to precipitate copper. Condensed ammonia and the filtered solution are returned to leaching. Heap leaching in the final repository cell lowers the capital investment significantly compared with competing extraction processes. Chemistry with respect to arsenic, sulfur and copper is discussed.

Jan 1, 1992

By H. Polat, Q. Hu, S. Chander

The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l%, however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent.

Jan 1, 1992

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

By Bell I. F

In 1985, ZC Mines (now Pasminco South) had been unprofitable for some years due to a combination of high operating costs, low metal prices, low head grade and an aging and inadequate mining infrastructure. However, the resource of metal in the ground was still of world class, even after some 80 years of mining. A major study, which was to be of two years duration, was therefore commenced to establish a practical and profitable long term mining strategy and to cost the infrastructure options needed for its support and thus form the justification for a capital expenditure program to take the mine profitably into the 21st century and its second century of operation. This paper discusses the rationale behind the methodology adopted and the nature of the results achieved in one aspect of the study - the determination of the mineable resource and the relationship between the head grade/quantity of the economically mineable resource and the variables of cut-off grade, cost structure, annual production rate and metal prices/exchange rates. The basis of the study was the designing of some 5000 scopes to mine out the entire resource for a range of cut- off grades and the assembly of the detailed physical data thus obtained in a stope-by-stope data base for financial and other analysis. Those scopes which were shown to be economically mineable were then scheduled for two optimum annual production/cut-off grade/metal price combinations to provide life-of-mine cost and value of production cash flows.

Jan 1, 1992

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

This paper discusses equipment replacement strategies and specifically addresses the upgrading of technologically superseded equipment. The process of equipment replacement evaluations is reviewed, and areas have been highlighted where currently accepted practice results in a bias towards retaining existing equipment longer than otherwise justified. The Discounted Average Cost Method is described and the advantages of the technique for this style of decision making discussed. Several key issues influencing the replacement evaluation are also presented together with examples from recent consulting work.

Jan 1, 1992

By Randall M. Wheeler

Pre-blast surveys are used to document the condition of a structure prior to the commencement of blasting activities. They provide the best means of determining the pre-existence of visible cracking and deterioration in a structure before blasting is initiated. A small investment in a good pre-blast survey, coupled with good public relations, could mean a large cost savings for a company in the future.

Jan 1, 1992

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By T. J. Haddon

For the mining industry in general and gold mining in particular the past few years have been difficult. Economic conditions coupled with growing regulatory restrictions have led to increasingly important reasons for managing assets wisely. From a public company perspective this makes sense because it ultimately provides for an increase in shareholder wealth and that's what we're in business to do. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today's competitive environment. So, as the CEO of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer --the Amax: Gold shareholder? Let me tell you. As I said earlier, the gold industry has been under siege. We have just completed our third year of average prices below $400 per ounce. When you add finding and/ or acquisition costs and development costs to operating costs, there isn't much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have at most a 10 year mine life. We are all scrambling to add reserves so we don't become extinct. As prices remain low, opportunities for increasing diminishing reserves abound. This is the time for the opportunistic company to take advantages of market conditions and that's precisely what we, at Amax: Gold, have done!

Jan 1, 1992

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By A. G. Pasamehmetoglu, N. Celebi, K. Erarslan

A deposit evaluation system has been developed for a proposed new mine in the basin around Collolar in Turkey. It includes compositing, gridding and reserve estimation facilities and takes account of the economic value of the pit and the pit bottom elevation

Sep 1, 1991

By R. H. T. Garnett

N.B. This paper provoked much (positive!) discussion in later issues, with responses from the author (and thanks also for the many private contributions he had received) - see under Garnett R.H.T. Expanded version of a paper originally presented at the Alluvial mining conference, London, 11-13 November 1991 and published in Alluvial mining, Barking: Elsevier Applied Science for IMM, 1991, p.115-156. The usual measure of performance in gold and tin dredging is the R/E factor. It compares actual production or recovered grade for a given period with that estimated from the original sampling. The factor is a multiple of four component factors, each ideally approaching 1.00. The factors are concerned with estimation, selection, excavation and treatment. The estimation factor reflects the errors involved in determining the grade and depth of single drill-holes or pits. An optimum selection factor is achieved by a higher drilling density. The excavation factor is affected by failure of the dredge to excavate the total volume contained within its course. The required dredge throughput rate influences not only the success in digging recovery but also the treatment factor. No two alluvial deposits are the same, but, in general, the greatest divergence from 1.00 is invariably demonstrated by the estimation factor. A major divergence in one of the other factors may also be the cause of the R/E factor being significantly different from 1.00. The component factors are examined in detail and historical trends in R/E factors are discussed

Sep 1, 1991

By H. K. Taylor

Ore reserves are inadequately defined. Geological reconnaissance and pre-feasibility mining work generate a broad range of valid tonnage estimates, many published for the benefit of various interests, who may view all figures as reserves. This work reviews the regular estimation of tonnages, grades and relevant factors for single deposits. A consistent framework of definition is suggested which, by conforming to the known structures of feasibility studies and long-range plans, avoids the pitfalls of over-categorisation and of unrealistic promises. Applications are based on North American experience but are intended for general use

Sep 1, 1991

By R. J. Gochin, G. D. Schena, R. Spencer

The impact of a mineral project in a developing country is evaluated in the broad context of its economy using input-output models. Minimum economic theory is used to develop simple numerical models. Sets of technical coefficients are exploited in the development of linear models of the productive element of an economy. The analysis allows assessment of the overall economic consequences of a mineral development in which issues broader in scope than financial objectives need to be incorporated in the evaluation. In part 1, the framework for the development of the input-output model is presented. The model is refined to incorporate country-specific behaviour. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy-wide effects associated with a new project in the mineral sector of a developing country. The relevance of the models is illustrated using an example from Namibia

Sep 1, 1991

The Aredor mine employs conventional dragline methods to exploit alluvial diamond deposits. Production began in 1984 with the policy of mining in the terrraces during the wet season and in the river flats during the dry season. Early production failed to meet predicted grades. A major geological programme to re-evaluate existing reserves was undertaken. This resulted in considerable increases in reserves in the river flats. Many of the reserve blocks included flats on both banks of the Baoule river. Methods of access into the river flats, normally flooded in the wet season, were developed to allow mining throughout the year. River diversions have been the main method used to provide access into the reserve blocks and, most importantly, to remove the risk of flooding. Aredor has carried out six main river diversions with a total length of 12 km. The diversions allowed production planning to be made on the basis of the economic evaluation of the reserve blocks, without undue regard to natural ground conditions or to seasonal factors. The Manning equation was used for the calculation of channel dimensions and gave satisfactory results. The practical aspects of the diversion preparations and flooding prevention are described

Sep 1, 1991

By Qing Wang, H. Sevim

Belt network simulators are the most widely used models in the design of belt networks. The simulators developed in the past two decades are reviewed and their limitations are discussed. To overcome these limitations and to provide a design model that can be used efficiently in real-life applications, a comprehensive non-simulation model has been developed. The features of this model are briefly discussed. A real example is used to demonstrate the model's superiority over belt simulators

Sep 1, 1991

By J. A. Hudson, X. D. Pan

A rock mass responds to excavation according to the properties of the intact rock, the network of contained discontinuities and the susceptibility of the rock mass to weathering. Large deformation often occurs when one of these components causes the rock mass to have a low strength relative to the stress conditions. Analysis of such large deformations forms a significant feature of current numerical modelling in rock mechanics. A practical large deformation problem of roadways in a coal mine is described, demonstrating the requirements for improving numerical techniques. The development of a numerical model is then summarised with particular attention to several concepts pertinent to large deformation analysis in geomechanics. A numerical case study is presented in which the developed finite-element model is used and the results are compared with the in-situ measurements. Conclusions are drawn for rock engineering that are also relevant to both civil engineering and mining engineering projects

Sep 1, 1991

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991

By J. S. Duval

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The compilation of the National Uranium Resource Evaluation aerial gamma-ray data to produce maps of the apparent surface concentrations of potassium, uranium and thorium for the conterminous USA has resulted in a reasonably accurate representation of the distribution of these elements in the surface rocks and soils. This claim is supported by the general agreement between the mapped geology and the patterns seen in the data

Jul 1, 1991