Search Documents

By P. J. Lloyd

There are few data on the composition of discard coal in South Africa, and no overall view of the discards for the entire industry. As a result of work on coal qualities in South Africa, a database was established which enabled a good estimate to be made of the composition of the discard from every mine. The data are presented in the form of histograms of ash, volatile matter and fixed carbon content of the 43 million tons of material which were discarded in 1990. The results are discussed in terms of the closeness of the composition of much of the discard material to presently used power station coal. It is concluded that it is mainly developments in equipment, particularly fluidized bed boilers, which inhibit the wider use of discard coal. However, other factors must be noted, including the relatively high sulphur content of the discards, and the fact that even with the most careful storage the material ages and may become unusable after about 15 years.

Jan 1, 2000

By J. D. Bosman

The problems associated with squeezing rock conditions in tunnels are well known and have been extensively investigated in the past. Although squeezing conditions are predominantly found in tunnels developed in weak rock types it has been noted at the No. 6 Shaft of Hartebeestfontein Mine where the host rock consists of hard, brittle quartzites. This paper investigates typical time-dependent deformation mechanisms in the rock at Hartebeestfontein Mine. The paper will focus on observations made in a strike-orientated tunnel that intersected weak quartzite layers, that were sandwiched between two competent quartzite beds. The observed squeezing mechanism is dominated by creep along bedding planes with a soft talcaceous infilling that behaves in a clay-like fashion when saturated in water. Stress-induced deformation processes, some distance into the sidewall of the excavation, force the already fractured periphery of the excavation into the void. A laboratory study of the creep of intact rock and discontinuities collected at this site was conducted to characterize the time-dependent behaviour. The difference in creep rates between the two types of quartzite found at this site is described in the paper. Creep tests performed on the talcaceous infilling material found that its presence allows substantial shear creep along discontinuities. Attempts were also made to simulate the squeezing mechanism observed underground with numerical techniques. Due to the discontinuous nature of the mechanism described above, a viscoplastic displacement discontinuity technique was used as it allowed for the explicit simulation of discontinuity creep. The results of the modelling and how it compared with the observed behaviour are described in the paper. Environmental impact statement The work described in this paper will not cause any new, or contribute to any existing, hazards confronting the environment.

Jan 1, 2000

By J J. Culberson

The past 10 years has seen use of computers become widespread in the mining/exploration industry (including coal, precious and base metals, oil/gas and industrial minerals). This paper will concentrate on the use of computers as a tool to provide technical solutions (including data management, mine planning and operational support) to this industry rather than the use of computers to aid accounting, maintenance and inventory (æcommercialÆ) applications. This paper will review the processes and benefits of the use of computers in mining. We then review the use of technical computing locally here in New Zealand and see what business benefits local users have found from using computers in mining. We have, in research for this paper, spoken with mining software vendors from around the world to find out what is currently the æbest practiceÆ in the industry. The paper will then list what those vendors see as the ultimate improvement on the cards for the future of mining software.

Jan 1, 2000

A fundamental component of grade control at Tarmoola Mine has been the monitoring of assaying through quality assurance programs. The programs have concentrated on issues related to accuracy and precision of leachwell and fire assay techniques, sample preparation and grade variability within a sample. An outcome of monitoring has been identification of shortcomings in the application of assaying techniques to Tarmoola ore types that contain coarse particulate gold. Leachwell has shown satisfactory precision since introduction as the primary assay technique in October 1998 but leachwell accuracy and recovery through comparison with fire assay techniques has identified bias. A bias toward higher fire assays in grades above 2 g/t invoked an investigation into the cause of the discrepancy between leachwell and fire assay. Testwork evaluated Leachwell assay recovery by varying leach time duration, which showed that by increasing the leach time improved recovery significantly. Monitoring of leachwell against fire assay had shown that a leachwell (200 g) with a one hour leach has under-called grade when compared with fire assay by up to 18 per cent, on average, for Tarmoola ore types. Alternatively, optimisation of the leachwell assaying technique using a 200 g pulp and a two hour leach has returned, on average, higher assays than fire assay by up to eight per cent. Testwork on screen fire assays, duplicate assays and fire assay to extinction has demonstrated assay variability associated with coarse, particulate gold. The variability and distribution of gold in Tarmoola ore types has emphasised the importance of high quality sample preparation for leachwell assaying to ensure liberation of gold to leaching solutions. Assay quality assurance protocols are vital to assay data integrity and enable confidence in delineation of ore-waste boundaries and provide early recognition of problematic assaying periods and isolation of grade control practices, which depart from performance standards critical to the operation.

Jan 1, 2000

By Claude Cunningham

Difficulty has always attended the evaluation of rock breaking energy available from explosives, owing to the complexity of the way in which it is released, and the destructive amplitude of the pressures. Many problems have arisen and continue with this difficulty, including the following: I. Formulation of improved compositions to deliver appropriate energy levels to the blasthole walls, or to deliver previous results at improved cost. How appropriate is it to use various ingredients, such as Aluminium, water, salt? 2. Claims over energy issues, resulting in wasted time and expense, over things that sound good in theory but are very difficult to tie down. 3. Purchasers of explosives make decisions based on claimed “Bang per Buck” from different manufacturers, where the estimate of “Bang”comes from simplistic numbers from various, very unequal detonation codes. The above problems are escalating as time progresses. Using the high level IDeX PC 2000 detonation code, we have found a way to portray the differences between formulations in a way which relates to their breaking effect in the field. The basic method is to plot the adiabat from the detonation state to full expansion in units which express the practical implications. Energy alone cannot deliver results, so we use the curve to examine its manifestations: pressure and temperature. Internal energy is plotted with these. The method displaces relative energy numbers, as it portrays the context in which the energy is available. It is used here to compare an ANFO, an emulsion and a doped emulsion, as well as the effect of Aluminium. The effect of the shock pressure regimes and temperature correlate well with what is seen in the field.

Jan 1, 2000

By J. Betzhold

Knowing more about an orebody makes it easier to exploit it profitably. Many orebodies are made up of different rock types, alteration zones or mineralogical ensembles: oxides versus sulphides or facies with different metallurgical properties for example. Being able to model the spatial layout of these different facies is vital to good mine planning and management. Kriging cannot be used to generate numerical models of orebodies with complex geometric patterns because it gives too smooth an image. Over-smoothing has the meaning of changing the natural selectivity. Conditional simulations are required to do this kind of model respecting the natural variability: honouring the natural selectivity, dilution and ore loss. Standard geostatistical simulations cannot duplicate many of the complex spatial relationships seen in the earth sciences, such as differently orientated facies, sets of conjugate veins or ore types where certain facies cannot touch. After a presentation of the case study, it will be shown why traditional methods for simulating indicators like the sequential indicator simulations, or the truncated gaussian method, cannot be used to simulate it. Plurigaussian simulations are then introduced and shown to be more powerful than the previous methods in their range of application. This is confirmed by the case study treated; a Chilean copper deposit, for which the plurigaussian simulations are seen to respect the different orientations of the individual facies as well as honouring the facies seen in drill holes, and respecting the proportion of each facies even if this varies in space (e.g. increases or decreases with depth). Key words: geostatistics, indicators, conditional simulation, plurigaussian method, copper variability.

Jan 1, 2000

By Seth L. Pearlman

Pin Piles are small diameter high capacity drilled and grouted piles also called minipiles or micropiles. They are ideal for building foundations on sites with poor ground conditions, sensitive surroundings, restricted vertical clearance, or difficult access. They are also well suited to foundation underpinning, arresting ground movements, and increasing the capacity of existing foundations. The major factors for selection of Pin Piles are reviewed; drilling, grouting, and design fundamentals are summarized; and a major case history is presented for the underpinning of the 43 story elevator core at the recently opened Mandalay Bay Resort and Casino in Las Vegas, NV.

Jan 1, 2000

By Andrew K. Simpson

What will this deal do to the company’s stock price? This question arises when a publicly traded mining company is presented with a new mine project, or business combination. The standard tool for addressing this question is to use discounted cash flow analysis, or net asset value(NAV), which is discounted cash flow net of liabilities. Cash flow-based analysis is invaluable for assessing project costs and other impacts on debt service capacity and internal rates of return. But cash flow analysis and NAV do not work very well for stock price analysis.

Jan 1, 2000

By Tony Robles

"A new process is disclosed for the recovery of gold and/or silver values from activated carbon wherein they are adsorbed as cyanide complexes. A unique chemistry allows the new process to use mill process water containing an inexpensive, non-hazardous compound as the eluant. The new process has an elution period of 5 hours at 98°C. The gold in the eluant can be recovered by electrowinning or zinc precipitation. The new elution process is simple, reliable, and provides an eluted carbon that may not require thermal regeneration before reuse. Retrofitting the new process to existing processes such as Zadra, Anglo, and others will not require significant capital expenditures.IntroductionThe efficient and reliable elution process for gold/silver from activated carbon is a very important process in the gold mining industry. The most common techniques for elution of gold cyanide from activated carbon are the Zadra and Anglo procedures.Specialized elution techniques like the Micron and Acetonitrile processes have not been commercialized to significant extent probably due to relatively complex unit operations and expensive reagents.Important functions of the gold recovery circuit are:Efficiently recover gold/silver from the loaded carbon.Carbon is in good condition for reuse for optimum recovery.The pregnant solution is amenable to electrowinning or zinc precipitation to recover gold/silver from the solution.The whole process to be simple and short to reduce gold inventories.Present Elution ProcessesTable 1 shows some carbon elution processes that are available today. The two main elution processes used in the industry are: (1) the Zadra process, in which hot cyanide solution is circulated through an elution column and electrowinning cells; and (2) the Anglo American Research Laboratory (Anglo) process, consisting of a pretreatment step with caustic cyanide solution, followed by elution with deionized water."

Jan 1, 2000

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By K. Severin, B. Flanigan, P. Marion

“Plutonic-related” gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As-(Sb-Hg) are a good empirical indicator of depth of emplacement and distance from causative pluton and have been used successfully in exploration. Results from a variety of analytical techniques also suggest a phenomenological cause for these metal associations, e.g. gold and bismuth have linked metallogenesis at high temperatures and thus are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2000

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By P K. Smith, N G. Corner, R J. Ryan, D C. Arne, F P. Bierlein

The Reefton Goldfield has produced 67 t of gold from mesothermal vein gold deposits in metasedimentary rocks of the Greenland Group (Cambrian-Ordovician). The Globe-Progress deposit contributed 13.2 t (418,000 oz) of this total, predominantly from quartz veins. Recently a resource of 14 Mt at 1.96 g/t Au (27.5 t or 882,300 oz of contained gold) has been delineated at Globe-Progress in quartz vein remnants and disseminated within adjacent sedimentary rock, much of which has been locally brecciated. The breccias consist of quartz vein and sedimentary wall rock fragments set in a matrix of clay ærock flourÆ and sulphide (arsenopyrite plus minor pyrite and stibnite). Gold, closely associated with sulphide, is disseminated within the breccia. Disseminated gold also occurs in massive siltstone and sandstone adjacent to the quartz veins and breccias. Exploration drilling at Globe-Pogress, and several other Reefton prospects (e.g. Capleston, Merrijigs, Big River and Alexander River), has intersected zones of disseminated arsenopyrite carrying up to 20 g/t more gold. These mineralised sediments commonly have little or no megascopic quartz and or carbonate veining. There is little visible indication of former primary or secondary permeability for the passage of hydrothermal fluid and deposition of gold. However, porosity and permeability were formerly present in inter-granular pore spaces and microveinlets now filled with quartz, carbonate and K-mica. The Fosterville gold deposit in Victoria bears many similarities to the Globe-Progress deposit at Reefton, in terms of age, host rocks, hydrothermal alteration and mineralisation style. Many ofthe disseminated deposits in Nova Scotia, including deposits at North Brookfield and Moose River (Touquoy Zone), have similar characteristics to the Reefton disseminated mineralisation, but commonly have abundant pyrrhotite and some deposits have disseminated metal alloy grains of complex metallurgy.

Jan 1, 2000

By T. K. Dichmann, J. A. Finch

"Microflotation, laboratory batch, and in-plant minicell continuous tests were conducted to determine if copper ions not only activate sphalerite but also depress pyrite when the minerals are together. Microflotation tests showed that pyrite recovery increased with addition of copper ions in the pH range of 5-10 when alone, but decreased when sphalerite was also present. Batch flotation tests (Red Dog ore) showed that upon addition of copper, pyrite recovery decreased significantly. The continuous tests (Louvicourt Mine) confirmed this and indicated that with excess copper pyrite recovery can increase. The results suggest there is competition for copper and xanthate in favour of sphalerite. To take advantage of this competition it may be necessary to control the sequence and rate of copper, collector, and lime addition. INTRODUCTIONFlotation, in common with all physical separations, is an imperfect process that results in misplacement of minerals. One source of this imperfection is accidental activation by contaminating metal ions. An important practical example is the misplacement of pyrite to zinc concentrates. Flotation of sphalerite generally requires activation by copper ions, added as copper sulphate. Copper ions are also used to activate pyrite [l] hence there is the suspicion that accidental activation contributes to the recovery of pyrite (Py) with the sphalerite (Sp). However, recent literature has shown that copper ions may make Py less floatable if Sp is also present. Xu et al. [2] conducted continuous minicell tests in-plant at Kidd Creek Operations (division of Falconbridge Ltd.) and showed that while the addition of copper sulphate improved zinc/iron selectivity, it did so as much by reducing the recovery of pyrite as increasing zinc recovery (Figure 1)."

Jan 1, 2000

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

In formulating its strategic plan in 1998 the New Zealand Minerals Industry identified two related critical issues facing it. These are, broadly speaking, the issues of access to minerals; and the perception the public has towards the industry and its behaviour towards the environment. This presentation will report on the Industry's response to the public perception issue. The Industry has, through the NZMIA Council, and its Communication and Website Committees, developed and implemented strategies covering: communication through the print media, and through its website www.minerals.co.nz, a long-term educational outreach programme with schools, focussing on the significance of minerals, their contribution to community wellbeing and the negligible long-term environmental effects of the Industry's activities.

Jan 1, 2000

By Frank Sames

Most Blasting Programs are developed focussing on the environmental impact with respect to blast vibration and airblast. Compliance with existing regulations or policies limiting the immissions are generally achieved through constrains in the blast design, or monitoring programs. Efficient monitoring programs combine compliance monitoring and blast assessment. Signals, which are obtained in the area of direct influence of the seismic source, can contain valuable information about the blast design parameters. Techniques to analyze blast vibration signals have advanced and can assist in understanding the contribution of individual blast parameters to blast vibration and airblast. Advanced signal analysis encompasses magnitude analysis, Fast Fourier Transforms (FFT) and frequency scans in the frequency domain, as well as filtering in the time domain. Through examples, the advanced signal analysis techniques and their limitations are described and discussed, showing the impact of blast timing, timing accuracy, charge configuration and the geology dependent transmission behavior. Optimization criteria and pragmatic monitoring programs can be developed on the basis of the most influential blast parameters. In addition, however, safety and the cost efficiency of the blasting program are essential to the success of an operation. That is where advanced signal analysis techniques can interface with blast planning, computer assisted modeling and information systems. A valuable process can be developed to ensure compliance with existing regulations and efficient risk management for mining operations, while tracking cost and supporting operational decisions. A conceptual blasting information system is presented.

Jan 1, 2000

By W. Kotze

The gold mining industry has mainly relied upon the use of highly polluting chemicals, such as mercury and cyanide to recover gold from its ores. The Coal Gold Agglomeration (CGA) process was developed some years ago and has the advantage in that gold is recovered by a procedure which has little or no negative impact on the environment. A gold ore containing liberated gold particles is contacted with coal-oil agglomerates, where by the gold is recovered into the coal/oil phase. Laboratory scale batch tests were performed on an artificial mixture gold slurry and gold recoveries of up to 85% were found under optimized conditions. By recycling the coal/oil phase, it was found that the gold loading onto the agglomerates was increased. Tests performed on an industrial ore yielded slightly lower gold recoveries, and X-ray Diffraction (XRD) analysis on the coal/oil phase showed that minerals other than gold was recovered into this phase. A comparative study was conducted whereby the CGA process was compared to mercury amalgamation. Gold recoveries obtained through amalgamation were 15% lower than by the agglomeration process, which indicates that this process can be considered favourably as an alternative to amalgamation.

Jan 1, 2000