Search Documents

By M. Moys

The use of temperature measurements for unusual applications in the analysis and control of column flotation and milling is discussed. This is followed by a review of some of the authors current research in the application of the discrete element method to the modelling of particulate processes, specifically milling, fluidized beds and chute flow.

Jan 1, 2005

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By Victor Raul Alarcon

The Ilo Refinery was commissioned in 1975, with a cathode production capacity of 150,000 tpy. In 1994, Southern Perú Copper Corporation (SPCC) purchased the Refinery from Minero Perú SA. Subsequently, in November 1999, Grupo Mexico acquired control of Southern Perú. The anode production facility is located at the Ilo Refinery. A number of effective operating and quality control practices have been developed that have improved anode quality, as well as increasing anode production capacity to 350,000 tpy. These, and other optimization actions have allowed for a current density increase from 213 A/m2 to 275 A/m2, while maintaining current efficiency at 98% and sustaining the high quality of the cathode. The paper will outline the scope of operational practices in the Anode Plant and provide some discussion on the Ilo Smelter modernization project, and the resulting impact on the existing anode plant.

Jan 1, 2005

By A. Founie

The United States continues to be the world’s leading producer and consumer of diatomite. Production of diatomite in the United States during 2004 was estimated to be 635 kt (700,000 st). This was a 2-percent increase from 2003. The value of processed diatomite in the U.S. was about $164 million in 2004. Production was from six companies with 13 processing facilities in four states. Nevada and California were the principal producing states. They accounted for about78 percent of the U.S. production during 2004. U.S. diatomite exports were about 136 kt (150,000 st). Imports were negligible.

Jan 1, 2005

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

By M. F. Dlamini

The hydrodynamics of a hydrocyclone present a complex internal flow structure, the numerical simulation of which remains a non-trivial task. We report on three-dimensional water-only computational fluid dynamics (CFD) hydrocyclone flow field predictions and highlight some of the issues concerned with the development of a CFD model incorporating an air core. The potential for the application of CFD as a hydrocyclone design tool is also discussed. Physically realistic velocity profile predictions were obtained, which challenge the classical account of the hydrocyclone radial particle classification mechanism. A pressure field distribution consistent with literature reports was also predicted. Keywords: hydrocyclone, computational fluid dynamics (CFD),classification mechanism

Jan 1, 2005

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By G. N. Shannon

Keywords: inclusions, slag, modeling, interfacial energy, capillary force, particle flotation, particle separation A previously introduced model of inclusions separating across a steel-slag interface, developed by Nakajima/Okamura and Bouris/Bergeles, is expanded to include different inclusions shapes (octahedral and plate-like, besides spherical) as well as comparison between model ladle-, tundish-, and mold-slags. Investigation of the relation of these shapes with the interfacial capillary force ? which arises due to the dynamic interfacial energy during separation ? has shown that the force has a significant effect on whether the inclusion separates rapidly or settles at the interface. For the slags considered, the most significant physical property is found to be viscosity, which resulted in fast separation times for inclusions in the mold and ladle slags, relative to the more viscous tundish slag. Particle dissolution (using experimental data) is included in separation modeling.

Jan 1, 2005

By V. K. Alves, P. Lacoste-Bouchet

"In order to improve ball milling efficiency in pellet plants, Companhia Vale de Rio Doce (CVRD), experiments new technologies in Santa Luzia (M.G. – Brazil) research center facility. Pilot grinding tests have been conducted with small grinding media, size distributed from 5 to 12 mm (millpebs). Tests have been conducted on an ore from CVRD’s Usina 5 Nibrasco, in Vitória, Brazil. A sample of the regrind circuit feed was obtained and used in comparative grinding tests with two types of grinding charges: 100% balls and a blend of 70% balls and 30% millpebs by weight. According to the balls charge, the grinding media mixture has showed the following benefits: reduction of the power draw, increase of the mill capacity, reduction of the circulating load and a slight increase of the ore blaine. Following the results obtained, CVRD is going to further explore the regrinding potential of millpebs.INTRODUCTIONCompanhnia Vale de Rio Doce (CVRD) is the largest mining company in Brazil. CVRD is involved in iron, base metals, gold and bauxite industries. Moreover, CVRD operates several pelletizing plants in Brazil and in other countries.CVRD’s Center for Mineral Development (CDM) is equipped with a comminution laboratory where studies are carried out that are aimed at the optimization of existing plants at several mining sites as well as the technical and economical feasibility of new projects. The laboratory is equipped with a complete pilot plant with several mills and classifiers, enabling continuous grinding tests in grinding circuits of almost any capacity and characteristics.In January 2004, CVRD undertook to conduct pilot tests at CDM for evaluating the effect of small grinding media on ball milling efficiency. Generally speaking, it is not unusual for operators to add oversize grinding media in a conventional regrind mill. This fact originates mainly from prohibitive prices of grinding media below 25 mm due to a production capacity decrease of grinding media producers. The size of the grinding media is an important variable affecting ball milling efficiency. Use of oversize balls decreases the number of contact surface between which particles can be caught and broken."

Jan 1, 2005

By J. M. Elder, W. S. Kow

Challenges to new heavy mineral deposit developments are presented. These include land use issues, particle fineness, declining grades, and particle coating, amongst others. Industry responses to these are presented as possible solutions.

Jan 1, 2005

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By D. J. Fourie

During the production of pure TiO2for the pigment industry, ilmenite, containing 35?60% TiO2, is reduced to high titania slag, containing 70?95% ?TiO2? and pig iron. The high titania slag produced, consists mainly of titanium in different oxidation states and FeO in equilibrium with liquid iron. To predict the phase and chemical reaction equilibria in a furnace, a suitable solution model is required with accurately determined binary interaction parameters, as slag melts tend to behave very non-ideally. This paper investigates two popular slag models, namely, modified quasi-Chemical (MQC) model and the cell model and provides the binary interaction parameters based on recently published data of the ternary system and critically assessed published unary and binary data. Very few modelling results have been published on the ternary Ti-Fe-O system pertaining to high titanium slags. The solution models, with their regressed interaction parameters, can subsequently be implemented in commercial software of the slag-metal phase equilibria to predict how much and which type of solids will precipitate for a given bulk slag chemistry and operating temperature or, alternatively, above which temperature should a furnace be operated to avoid excessive solids precipitation.

Jan 1, 2005

By Shemek Oginski

The 5 km (16,194 lf) of 6.1m (20 ft) diameter TBM driven tunnel built by the J.F.Shea Co. will serve as sewage overflow storage. The TBM tunnel and four connecting tunnels excavated by drill and blast methods in hard granite will remain unlined. Based on the Geotechnical Baseline Report (GBR), the Contract documents provided a design with no required pattern of rock bolts, no probing, no pre-excavation or consolidation grouting, and lastly, no final lining of the tunnels was deemed necessary. This paper will provide a general overview of these topics with the emphasis on the actual ground conditions encountered versus the projected conditions provided in the GBR and how the GBR reflected the design of the project. Proposed modifications to the temporary and permanent ground support will be presented and the necessity of probing and pre-excavation grouting will be evaluated.

Jan 1, 2005

By A Kamkar-Rouhani

The paper describes a mineral potential mapping of gold and other base metals in Mahneshan area, Iran, using geographical information system (GIS), in which, the method of weights of evidence is used to combine spatial data obtained from different sources to make prediction for mineral potential. This is a quantitative tool for mineral resource mapping that can be used to delineate and predict favorable areas for further exploration by using the characteristics of known and similar mineral deposits. In accord with the descriptive model for gold and other base metal deposits, the spatial distribution of 20 known mineral occurrences was used. In addition, digital evidential maps were used in this study. The maps include maps of lithological units, faults and first derivative of total aeromagnetic data, remotely-sensing data of alteration and also geochemical evidential maps produced on the basis of the results of chemical analyses of samples taken from the stream sediments in the area, and analysed for Cu, Pb, Zn, Sb, As, Ag, Au, Ba and Hg elements. The binary maps were produced and then combined with the model of weights of evidence using 20 known mineral occurrences to obtain a final map of the favourable areas for further exploration of gold and other base metals in the study area. The final map is a predictive GIS model of the mineral deposits in the area. An interesting matter about the final predictive GIS model is that the faults are mainly located in favorable areas which possesses the most probability of mineralisation. Therefore, the faults in these areas have priority for further exploration of gold and others base metals.

Jan 1, 2005

By Michael S. Kucker, Stuart Warren, Robert A. Robinson, Michael J. Lehnen, David McAllister

Geotechnical conditions exposed by the phased exploration programs have had a major impact on the selection of excavation and support methods, dewatering requirements, size of openings, vertical alignment, and estimated cost of construction for the Beacon Hill Tunnel and Station section of the “Link” Light Rail. Beacon Hill is comprised of a very complex glacial geology, including numerous slickensided fractures, injected sand dikes, and multiple perched groundwater levels as revealed by a phased boring program and exposed in a test shaft. The Geotechnical Baseline Report (GBR) presents this complex geology along with a “tool box” of alternative additional support systems to accommodate the varying ground conditions during construction of the station excavation. Additional explorations will also be accomplished during construction to further refine the geotechnical interpretations and provide an opportunity to use pro-active ground improvement techniques to optimize the station excavation and support requirements.

Jan 1, 2005

By K. N. Santini, J. M. Barker

The perlite industry in the United States continued to undergo rapid change and increased competition last year as it did in 2002. U.S. production in 2004 was 510 kt (562,000 st),an increase following five consecutive years of decline (Table 1). Perlite is exported to Canada and to the Pacific Rim. These partially offset imports. Perlite imports from Greece to the eastern and Gulf Coasts of the United States declined by about 22 percent after reaching a record 240 kt (264,000 st) in 2003.But their market remains protected by high rail rates from western U.S. plants. Minor imports of perlite persist by Termolita from Mexico.

Jan 1, 2005

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By G. van den Berg

Anglo Platinum has initiated a project to investigate hydraulic hoisting technology for platinum mines. Hydraulic hoisting systems are categorized as pumping, fluidizing feeder or displacement feeder systems. Positive displacement piston diaphragm pumps are most suitable for pumping systems but they require that the ore be milled prior to pumping. Fluidizing feeders are unsuitable for platinum ore applications due to the large percentage of fines in the ore. The three-chamber pipe displacement feeder has been most widely used for hydraulic hoisting and is the most suitable technology for platinum mines. Eight hydraulic hoisting applications covering pumping and displacement feeder technologies are reviewed. The key factors to be assessed in selecting a hydraulic hoisting system for a platinum mine are discussed. A typical platinum mine configuration will comprise an ore preparation plant (to produce -15mm material through screening or crushing), motive water pump on surface, high pressure water pipeline from surface to underground, ore slurrification plant, three-chamber displacement feeder, and a high pressure slurry pipeline to surface. The water and slurry pipelines are housed in a purpose drilled borehole. A hydraulic hoisting system selection chart is presented. A 150mm diameter system with a 25 MPa pressure rating is required to hoist 60 000 t/m from a depth of 1 200 m. Generic capital and operating costs are presented. A major potential advantage of hydraulic hoisting is that the fines, which contain a high percentage of PGMs, are captured underground and transported directly to the concentrator. Hydraulic hoisting technology is ideally suited to providing supplementary hoisting capacity to existing shafts that have reached the skip hoisting capacity limit. The main advantage for new shafts is the potential to significantly simplify underground rock handling and transportation. All hydraulic hoisting system components are proven. The only risk area is the wear rates of the valves and piping. Current estimates are based on gold ore. The business cases investigated show that the financial viability of the installations are not sensitive to wear rate. Hydraulic hoisting is technically feasible and financially attractive for platinum mines. Keywords: hydraulic hoisting, slurry

Jan 1, 2005

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

Although AustraliaÆs coal mining industry is currently experiencing a pleasing period of price relief, long-term trends toward lower real prices will surely continue. Higher price levels attract expansion by existing operators and market entrance by new operators. History clearly demonstrates the relentless long-term march toward ever lower real prices. Therefore, the need for economic returns applies constant pressure to improve productivity. To be sustained, high productivity requires a systematic response based on a solid understanding of critical productivity determinants. The most powerful determinant of productivity is now widely understood to be workplace culture. Culture largely comprises a combination of behaviours, symbols and attitudes. This paper will examine and review scienceÆs latest discoveries in human behaviour. It will provide a proven, practical framework for understanding behaviour and applying this knowledge. Significantly, it will highlight why conventional approaches toward improving productivity often provide disappointing economic returns. The modern understanding of behaviour factors will cover coal face operations. More importantly, because executive and managerial levels in coal mining have significantly greater impact on industry and mine productivity the paper will concentrate on leadership. Particular emphasis will be placed on use of modern systems and in particular use of what are by far the most powerful drivers of behaviours û measurement, analysis and reporting systems. The paper and presentation will show how conventional systems rooted in antiquated American legislation from the early 1900s stifle productivity improvement and drive suboptimal and even counterproductive behaviours. These commonly used systems will be compared with accurate and effective modern methods for assessing performance to improve productivity. These principles are proven in all industries and effective application in mining will be highlighted. Actual results will be used to demonstrate practical approaches successfully applied in both metal and coal mining in Australia and overseas.

Jan 1, 2005