Search Documents

By Alan D. Curtis

A standard planning block model for Phelps Dodge North America Operations has been developed to improve mine planning efficiency and performance in a skill starved environment. The model saves time on software management and training, consolidates data and standard information/output, enhances evaluation and strategic process, and improves communication between sites.

May 1, 2007

By A. S. Moghaddam

The transportation of cemented and non-cemented mine tailings in the form of paste through pipelines is one of the main stages of paste backfill operations. For the purpose of pipeline design, the rheological properties of the materials, such as yield stress and viscosity must be determined. In this study, the yield stress of two Canadian mine tailings, for gold and copper mineralization, were studied using the vane method and slump tests. The comparison between the vane method and the slump tests indicates that the slump tests generally overestimate the yield stress values for both cemented and non-cemented paste backfills. In addition, the effects of 5% Portland cement (type 10) and mixing time on the yield stress of paste backfills were investigated. The percentage of cement as a binder agent has a direct effect on the increase of the yield stress of paste backfills. Yield stress measurements show that mixing times of 4 minutes and 12 minutes have the same effect on the yield stress values.

May 1, 2007

By L. Li

The backfilling of underground stopes is a common practice throughout the mining industry. The stresses imposed by the backfill on the surrounding rock mass need to be assessed because of their influence on ground stability and on the hydro-geochemical response of the fill material. There is, however, a complex interaction between the relatively soft backfill and the much stiffer adjacent rock mass. In recent years, the authors have presented results from investigations conducted on stress distributions (obtained numerically and analytically) in and around backfilled stopes with (sub)vertical walls. In this paper, the influence of stope inclination and of backfill properties is evaluated. Results indicate that, in general, the vertical and horizontal stresses in inclined stopes are close to, but somewhat smaller than the stresses in vertical stopes. Nonetheless, significant differences can be observed in some cases, especially for the vertical stress along the inclined central line and along the hanging wall. It is further shown that neglecting deformability in limit equilibrium analyses is an acceptable assumption. However, Poisson?s ratio and the dilatancy angle, usually neglected in limit equilibrium analyses, may have significant effect on the stress distribution. Results also confirm that the backfill strength parameters (cohesion and friction angle) are critical factors required to properly evaluate the stress distribution, at least within a certain range of parameter values.

May 1, 2007

By Jason J. Ballentine

This case study presents the results of a maintenance review of a soot blower system at a coal fired power generation station. The power generation station was following a ?repair when it breaks? maintenance strategy for its soot blowers. The efficiency losses incurred as a result of failures in the soot blower system and the resulting interruption and out of service time was found to have a significant effect on the plant output. The maintenance strategy for the soot blowers was reviewed using Reliability Cantered Maintenance and lifecycle simulation. This methodology provided visibility to the monetary implications of failures and allowed alternative types of maintenance to be assessed and where justified were added to a maintenance schedule in the Maximo work order management system. By reducing unplanned breakdowns the predicted reduction in efficiency losses was 45%.

May 1, 2007

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By D. Mark Richards

Highland Valley Copper (HVC) is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using GPS has been utilized at the mine since 1996 for blast hole drill navigation and since 2000 for shovel and dozer navigation. Since 1997, rock recognition has been part of the drilling process. This allowed the mine to develop a Mine to Mill strategy using the rock hardness information from drill monitoring systems to both refine drilling and blasting parameters as well as downstream crushing and grinding strategies. Although this preliminary effort has been very successful at HVC, the current intent is to gain further benefits through better use of existing information while also deriving an enhanced data set from monitoring production drills. In the latter case, the objective is to acquire and process drill variables in such a manner as to permit more detailed definition of rock mass characteristics. The subsequent focus will be to use the derived geotechnical and geological information as part of a practical process to more prescriptively blast the rock mass. Through the definition of domains based on drill monitored derived rock mass properties, the intent will be to enhance blast outcomes that lead to optimized downstream (from blasting through to concentration) processes in a more proactive and timely manner. This paper examines a proposed approach to be able to derive more accurate and consistent rock mass properties from production drilling. In addition, the discussion will identify potential benefits to be gained from process improvements that result in enhanced productivities, and crushing and grinding optimisation due to blasting strategies that are more closely matched to identify rock mass characteristics.

May 1, 2007

By Guy Chevalier

The QCM Mount-Wright mine and concentrator complex produces about 14 M tonnes of iron concentrate annually. Approximately 9.5 M tonnes of this concentrate are used to produce iron ore pellets at four different silica grades: Three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the realization of two projects where the acquisition of new process equipment led to an improved pellet plant iron recovery, a better flexibility and to lower operating costs as well as to the production of fine iron ore concentrate from the Port-Cartier tailings pond. Typical 4.8 % SiO2 concentrate is processed to achieve required pellet silica content. This is obtained with the aid of hindered settlers or hydraulic classifiers, screens, whims and, lately, spirals. The increasing demand for low silica iron ore products resulted in a greater need for upgrading. The Pellet Plant upgrading capacity being limited, more and more iron units were lost. Base on test works results and economic evaluations, QCM engineers figured out a way to increase efficiently their upgrading plant capacity and go back in the pond gather what has been lost in recent years of operation.

May 1, 2007

Research by the National Institute for Occupational Safety and Health (NIOSH) on multiple-seam mining has resulted in two new ground control products. Information Circular (IC) 9495 In some U.S. coalfields, particularly in central Appalachia and the West, most mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously threaten the safety of miners and disrupt mining operations. Information Circular (IC) 9495 is a proceedings document containing a variety of papers that summarize recent knowledge about multiple-seam mining. A NIOSH study that analyzed case histories collected from 44 U.S. coal mines is described in detail. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. The study's results were the basis for the Analysis of Multiple-Seam Stability (AMSS) software package. The proceedings also contain two papers describing the LaModel family of software. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D implements a simplified, two-dimensional model suitable for quick approximations of the multiple-seam stresses and strains. Three papers in the proceedings focus on case histories. One describes the extensive multiple-seam experience at the Harris No. 1 Mine in West Virginia, a second contains examples of "extreme" multiple-seam mining from the central Appalachian coalfields, and a third describes interactions with regard to longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining. [ ] AMSS Software Package NIOSH has developed a simple, user-friendly computer program called Analysis of Multiple-Seam Stability (AMSS). AMSS can help mine planners to evaluate each potential multiple-seam interaction and take steps to reduce the risk of ground control failure. AMSS begins by evaluating the pillar design. It first calculates the single-seam pillar stability factor (SF)

Jan 11, 2007

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

Rock mass classification is widely used throughout the underground mining industry—in both coal and hard-rock mines. It is used in all stages of the mining process, from site characterization to production operations. The goal of the International Workshop on Rock Mass Classification in Underground Mining was to provide a forum for leading practitioners of rock mass classification to come together and share their methods and experiences with the technique. The workshop was held in Vancouver, British Columbia, Canada, on May 31, 2007. It was co-chaired by Christopher Mark, Ph.D., P.E., National Institute for Occupational Safety and Health, Pittsburgh, PA, and Rimas Pakalnis, P.Eng., University of British Columbia, Vancouver, Canada. The proceedings of the workshop contain 16 invited papers from 9 countries, reflecting the international depth and breadth of current practice. Applications in both hard-rock and coal mining are well represented. Some of the topics that were addressed at the workshop include: • Major rock mass classification systems used in mining and their variants • Collection of input data through observation, rock testing, and geophysics • Design of mine layouts and rock support systems using classification • Estimation of rock mass strength and other input parameters for numerical models from classification • Applications in weak rock, raise boring, cavability assessment, and other special topics • Risk assessment using rock mass classification

Jan 5, 2007

By Rimas Pakalnis, Andrea M. Ouchi, Thomas M. Brady, Mary M. MacLaughlin, Cristian Caceres, Paul Hughes

A major focus of ground control research presently being conducted by the Geomechanics Group at the University of British Columbia, Canada, in conjunction with the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory, is the development of design guidelines for underground mining within weak rock masses. The study expands upon the span design curve for man-entry operations and the stability graph for nonentry operations developed at UBC by extending the application to weak rock masses. The original database has been augmented by weak rock mass information from mines throughout the United States, Canada, Australia, Indonesia, and Europe. The common factor in all of these mines is the presence of a weak back and/or walls. This paper expands on the North American database and how the design curves have been employed at mining operations throughout the world. The definition of a weak rock mass for this study has been defined as having an RMR76 under 45% and/or a Q-value under 1.0.

Jan 5, 2007

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By Jeremy P. Doolan, Leigh B. Neindorf, Geoff W. Capes

The development and use of rock mass classification tools have been a key component for improving stope design over the past 4 years at the Xstrata Zinc George Fisher Mine in northern Queensland, Australia. In 2003, stope extraction data from 3 years of open-stope mining provided an excellent situation to review the assumptions in the feasibility study. Extracted stope profile information, drillhole geotechnical data, underground observations, and oral and written communication were used to develop a thorough stope reconciliation performance database. With-out collecting the back analysis data and presenting the data in a usable format, engineers are left to debate opinion instead of engineered judgment. This can lead to biased and uninformed design parameter choices with the potential to repeat poor design. This paper demonstrates some effective, practical examples of empirical data collection where rock mass classifications tools were developed and used to create improved confidence in predicting stope stability and failure profiles. The work contributed to design changes that resulted in a reduction in stope hangingwall dilution and an increase in head grade while continuing to ramp up production from 2003–2005.

Jan 5, 2007

By Paul G. Marinos, Vassilis Marinos, Evert Hoek

The Geological Strength Index (GSI) is a system of rock mass characterization that has been developed in engineering rock mechanics to meet the need for reliable input data related to rock mass properties required as input for numerical analysis or closed-form solutions for designing tunnels, slopes, or foundations in rocks. The geological character of the rock material, together with the visual assessment of the mass it forms, is used as a direct input for the selection of parameters for predicting rock mass strength and deformability. This approach enables a rock mass to be considered as a mechanical continuum without losing the influence that geology has on its mechanical properties. It also provides a field method for characterizing difficult-to-describe rock masses. Recommendations on the use of GSI are given and, in addition, cases where the GSI is not applicable are discussed.

Jan 5, 2007

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

By Desiree Willis

Disc cutters have determined excavation rates of rock tunneling projects for more than 50 years. First developed in 1956 by James S. Robbins, disc cutters (then 279 mm or 11 in. in diameter) were used to bore limestone of 190 MPa (27,500 psi) unconfined compressive strength (UCS) and were loaded with 7.12 t (15,700 lbs) each. Modern cutters have reached up to 508 mm (20 in.) in diameter and are typically loaded with up to 31.7 t (70,000 lb) to economically bore through the hardest of rock up to plus 400 MPa (60,000 psi) UCS. New developments, such as larger cutter diameters, are geared to increasing the bearing capacity and wear life of the cutting structure. This, in turn, increases cutter life, cutter load and cutter penetration. Disc cutters have also been re-designed on a small scale for use in hard-rock utility installations. Additional variables also affect the three factors, including cutter spacing on the cutterhead, cutterhead diameter and cutter materials.

Jan 1, 2007