Search Documents

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Ertugrul Kaya, Kagan Ozdemir

The results of bench blasting on quarries, have important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc., and the total costs of that mine. Drilling and blasting is an important step in mine producing chain and its results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. Within the scope of this study, the three different hydraulic excavators’ working performances have been studied considering the particle size distribution after bench lasting at a quarry in Istanbul Turkey. Five shots have been realized on the quarry and average particle size of muckpile after each shot were assessed by digital image analysis method. Bucket loading times have been measured by stopwatch study after five shots. Excavator bucket loading times were also estimated by bucket loading time estimation formula which was published in ISEE 2007 Conference, Ozdemir et al. 2007. Estimated and measured times have been statistically analyzed and the accuracy rate of formula has been determined for five events.

Jan 1, 2008

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008

[ ]

Jan 1, 2008

By Helen D. Robinson

The seawalls that surround Ellis Island were constructed in the early 1900s and now show varying degrees of deterioration. An innovative approach to the structural repair of the seawalls was developed, which consisted of the use of micropiles for stabilization of vertical and horizontal seawall movements. The micropiles were installed through the existing seawalls and penetrated through a thick overburden, consisting of soft alluvial deposits and relatively hard glacial till, and were bonded into Manhattan Schist. Drilling of the micropiles often encountered timber and other obstructions. The selection of micropiles for stabilization of the seawalls offered significant advantages over other foundation systems and over alternative soil improvement techniques. They allowed drilling through a variety of materials without the need for significant retooling or changes to the drilling procedure. This reduced the impact of foundation construction on the sensitive historical landscape and structures, and prevented the need for significant foundation work from the water side of the seawalls. In addition, micropiles offered relatively high installation rates and flexibility to adapt to the varying conditions along the seawalls.

Jan 1, 2008

By John E. Newby

The Brightwater Conveyance System consists of four tunnel segments in three tunnel con-tracts, comprising over 21,760 m (71,400 ft) of pressurized face tunneling in complex glacial and non-glacial soft ground conditions with a large proportion 60 m (197 ft) or more below the ground surface with up to 7 bars groundwater head. This resulted in unique technical challenges for establishing geotechnical baseline values. The process used to develop these baseline values and specifications with regard to the level of risk that the owner, King County, was willing to accept is described in this paper.

Jan 1, 2008

By K. G. Thorne, D. R. Lentz, A. F. Park

"The Main zone of the Clarence Stream gold deposit is hosted by a shear zone adjacent to the Saint George batholith in southwestern New Brunswick. The mineralization history relates to progressive deformation in the shear zone and the intrusion of the Magaguadavic granodiorite.Of three phases of deformation that have affected the area (D1-D3), D1 is not observed in the Clarence Stream shear zone. Two suites of igneous rocks intrude the shear zone: post-D2, pre-D3 gabbro; and granitic dikes, which crosscut the gabbros. Granitic dikes show a diverse range of relationships to D3 features, from pre-syn-D3 mylonitic fabrics in transposed and highly deformed enclaves, to nondeformed and entirely discordant dikes (post-D3).A variety of veins occur within this shear zone. Zoisite-bearing and later, crosscutting epidote-bearing veins are preserved as relics in quartz-mylonites, and predate quartz veins that host gold mineralization. The epidote-bearing veins are associated with pseudotachylitic cataclasite dikes, consistent with transient brittle failure during ductile deformation.Deformation relates to right-lateral strike-slip motion across the shear zone, and subhorizontal and near-vertical stretching lineations imply transpression. A late (late- or post-D3) dip-slip phase of motion is also apparent, and cooling followed a metamorphic peak early in D2-D3 history. Deformation of the shear zone, and more localized transient brittle failure, provided the permeability for fluid movement and vein emplacement. This scenario is similar to the findings of other studies, in which geochemical, tracer isotopic, and age-dating (U/Pb, 40Ar/39Ar) results suggest that the adjacent Magaguadavic granodiorite provided heat and metals. La zone principale (Main zone) du gisement d’or de Clarence Stream est encaissée par une zone de cisaillement qui longe le batholite de Saint George dans le sud-ouest du Nouveau Brunswick. L’historique de la mise en place de la minéralisation accorde un rôle important à la déformation progressive dans la zone de cisaillement et à la mise en place de la granodiorite de Magaguadavic.Des trois phases de déformation à avoir affecté la région (D1-D3), les effets de D1 ne sont pas observés dans la zone de cisaillement de Clarence Stream. Deux suites de roches ignées se sont mises en place dans cette zone de cisaillement : un gabbro post D2, pré-D3 et des dykes granitiques qui recoupent le gabbro. Les dykes granitiques montrent une grande diversité de relations avec les structures D3, allant de précoces à synchrones aux fabriques mylonitiques D3 dans des enclaves transportées et fortement déformées à des dykes complètement discordants et non déformés (post-D3).On note diverses veines dans cette zone de cisaillement. Des veines contenant de la zoisite ainsi que des veines d’épidote sécantes plus tardives, lesquelles sont préservées comme reliquats dans les mylonites à quartz et sont plus vieilles que les veines de quartz contenant la minéralisation aurifère. Les veines d’épidote sont associées à des dykes de catacalasite à texture de pseudotachylite, compatibles avec une rupture cassante épisodique durant la déformation ductile.La déformation résulte d’un mouvement décrochant dextre le long de la zone de cisaillement et les linéations d’étirement subhorizontales et quasi-verticales impliquent de la transpression. Une phase tardive (tardi- ou post-D3) de mouvement selon le pendage est aussi apparente, et le refroidissement succède à un pic métamorphique tôt dans l’histoire D2-D3. La déformation de la zone de cisaillement et la rupture cassante épisodique ont fourni la perméabilité nécessaire au mouvement des fluides et à la mise en place des veines. Ce scénario est similaire à celui proposé par d’autres études, dans lesquelles les résultats de géochimie, de traceurs isotopiques et de géochronologie (U/Pb, 40Ar/39Ar) suggèrent que la granodiorite de Magaguadavic avoisinante a fourni la chaleur et les métaux."

Jan 1, 2008

The use of a time series variogram as an aid in controlling the quality of a product was pioneered by Pierre M. Gy and is described. The ability to analyse and interpret covariance relationships time series data is possible using the variogram. The concept of stream heterogeneity allows sources of variability in process streams to be identified and isolated. Principally this is distributional heterogeneity that is due to a short range effect of segregation in the process stream related to size or composition distribution of the material on a local scale and due to a long-range change in the size and grade of the material stream. The variogram is simply a tool for representing these sources of variability in a way that is explicit, allowing identification of the source and providing important insights to temporal continuity between samples. This paper describes the chronologically related large-scale variability in an iron ore process stream (%Fe), and illustrates the control and mitigation of variability at various stages within the process using a variogram. Three main sources of variability are identified including the random variability V[0], the process variability V[1], and the variability due to cyclical phenomena V[cyclic], arising from human routine or mechanical defects. These sources of variability can be represented on the control chart that provides the plant superintendent with insights as to the sampling capability of the systems in place. Maintaining levels of variability within customer specification limits requires that production systems be controlled without overcorrecting for the trends in changing quality. This can be done only by representing the limits of control relative to the limits of specification on a control chart. Where the specification limits encroach on the control limits, one or the other, or both, may need to be changed; specification limits that constrain the control limits lead to reactive decision making that is expensive and stressful for plant operators.

Jan 1, 2008

By A R. Penney

Since mining-induced seismicity first became apparent at the Beaconsfield Gold Mine in 2002, there has been an ongoing program of geotechnical investigations to understand the phenomenon and allow for the development of strategies to manage the risks it posed to personnel, the business and the community at large. Studies resulting from a seismically induced rockfall on Anzac Day 2006 have been extensive, and have advanced the understanding and management of seismicity at the mine. Enhancement of the mineÆs seismic array, implementation of extensive monitoring of ground behaviour, improved ground support and reinforcement design, and ongoing numerical modelling provide a technical framework for the management of seismicity. In addition, extensive involvement of the workforce in risk assessment and the development of standard work procedures (SWPs), has contributed to a æbest practiceÆ approach to manage seismic hazards at the mine.

Jan 1, 2008

Research into the mechanisation of ore winning from the very narrow reefs characteristic of South African gold mines has been conducted from as early as 1964 through the Chamber of Mines Research Organisation (COMRO) but with limited success. However, the Council for Scientific and Industrial Research (CSIR) has recently re-evaluated the potential for the mechanisation for the narrow tabular gold mines. It has been determined that there are approximately 22 000 tonnes of gold left in-situ in channel widths of less than 500 mm in thickness. The extraction of ore from such reefs requires a complete paradigm shift in that the current mining cycle (drilling, blasting, cleaning and supporting) is not feasible since such a stoping width would not allow the workers entry into the stope. Consequently, a non-entry form of mining is required. With this target in mind CSIR has invested in a project called the Nederburg Miner which seeks to identify new technologies for drilling, rock breaking, cleaning, and materials handling, the application of which will enable non-entry mining of very narrow ore bodies. The intention is to develop a fully automated system that will not require human involvement at the stope face. The outcomes of research into this proposed system will not only extend the life of South African gold mines but will also enhance South Africa's reputation for excellence in mining research. This paper presents the new technologies under consideration and potential methods for their application into an integrated non-entry mining system.

Jan 1, 2008

By B. Ndlovu

The world mineral industry has over the years experienced growth in the production of nickel (Ni) due to its use not only in the catalytic industry but mainly also to its demand in the stainless steel production industry. Hence there is a need to produce more pure and marketable grades of Ni through the use of efficient purification routes such as solvent extraction. The V10-LIX®84-IC system resulted in nickel (Ni) extraction isotherm shifting to lower pH levels. The pH window of opportunity for the extraction of Ni subsequently increased in solution containing magnesium (Mg) and calcium (Ca) even though the system also resulted in slight shifts to less positive pH values for Mg and Ca curves. Results showed a synergistic effect of LIX®84-IC when added to V10 for all elements, Ni, Mg and Ca. The pH50 values for elements Ni, Mg and Ca in the V10-LIX®84-IC system were 2.95, 8.10 and 7.70 respectively. Comparing results obtained when using V10 alone produced ?pH50 for Ni, Mg and Ca being 3.35, 0.15 and 0.70 respectively, which was a confirmation of the synergistic shifts for all the elements. The ?pH50 (Mg-Ni)value was 1.95 with no synergism and 5.15 with synergism and that for ?pH50 (Ca-Ni)was 2.10 with no synergism and 4.75 with synergism. This showed that the Ni-Mg separation factor was relatively larger than the Ni-Ca. Improved loading and stripping kinetics were also observed. Keywords: Nickel solvent extraction separation, magnesium, calcium, versatic 10 acid and LIX®84-IC.

Jan 1, 2008

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the three-dimensional surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. In this paper, the authors discuss the signal processing techniques used to study these relationships, as well as the related implications for mining.

Jan 1, 2008

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

From the massive equipment that moves the earth, to the parts that keep the equipment moving, it was all on display for more than 35,000 people who at-tended MinExpo 2008 at the Las Vegas Convention Center Sept. 22-24. In the largest show in the illustrious history of MinExpo, the success of the recent commodity boom was reflected in the more than 55,700 hm2 (600,000 sq ft) of floor space that was jam-packed with nearly 1,300 vendors. Among them, the makers of the industry?s largest machines, displaying their latest and greatest trucks, shovels, excavators, drills and other mining equipment. During the nearly decade-long commodities boom, equipment makers have worked hard to keep up with demand while also investing heavily in research and development. The beneficiaries of this R&D is the end user who saw first-hand at MinExpo 2008 the many advances that have already been made in safety, comfort and productivity from all the manufacturers. R&D has also helped spark more talk of automation, which is being used already at some of the world?s largest mines. Caterpillar and Komatsu have worked with the technology in surface mining and Bucyrus and Sandvik are among the industry leaders applying the science of automation to underground mines. Technology has in-creased greatly since the idea of moving massive equipment remotely was first knocked around and the idea of entire fleets operating around the clock seems to be getting closer to reality. But, until that happens, MinExpo attendees were treated to a show that featured some of the most impressive current machines the industry has to offer. In the largest booth space of the convention, Caterpillar (www.cat.com) displayed the culmination of an ambitious $280-million dollar investment, with the introduction of its new mining fleet of four new trucks. The F-series was un-veiled with common features in safety, cabs, engines, frames and bodies and Tier 2 compliant engines. The F series also features a return to the electric drive option. ?When our customers asked us for improvements to our mining trucks, we responded by making a record investment in every single truck in our line, as well as the increased capacity to produce more of them,? said Cater-pillar group president Stu Levenick. ?New technologies have allowed us to make trucks more reliable, easier to maintain and more friendly to the operator and to the environment.? The 793-series is in the 218- to 227-t (240- to 250-st) class that will be available in both mechanical (793F) and electric (793F ac) versions. The electric drive-only 313- t (345-st) 795F was also introduced, while the flagship 797B truck is in the process of being replaced by the new 797F mechanical drive, maintaining its 345- to 363-t (380- to 400-st) target payload. Completing Caterpillar?s new mining truck line will be new versions of the 785 and 789 mechanical drive trucks. The next generation of trucks will be phased into production during the next two years, with the Cat ac drive models expected to go into production in late 2010. The $280-million in-vestment is Caterpillar?s largest commitment ever to the mining industry

Jan 1, 2008

By Mark Rybak

On Aug. 31, 2006, Tropical Storm Ernesto hit the city of Richmond, VA. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This article describes the fast track design, bidding and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft-sinking methods and final lining design all contributed to the success of this project. The storm inundated Richmond, VA with up to 305 mm (12 in.) of rain that, in some areas, caused widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed and caused local combined sewer and stormwater flooding. The collapsed sewer was a 2.4-m x 76-mm (8-ft- x 3-in.-) wide by 2.7-m- x 152-mm- (9-ft- x 6 in.-) high arch sewer that was constructed in the 1920s and later filled over with municipal solid waste and a soil fill cap to cur-rent elevations. A sinkhole was created in the area of collapse approximately 18 m (60 ft ) deep and 31 m (100 ft) in diameter. This caused the existing arch sewer to become blocked. As a result of this blockage, contaminated floodwaters reached depths in low-lying areas in excess of 8 m (25 ft).

Jan 1, 2008

Gary R. Steele is vice president, corporate marketing with Energy Fuels Resources. As such, he knows the global uranium market. The following are some of his thoughts on uranium?s place in the global energy picture. ME: What are Energy Fuels Resources? thoughts on the global nuclear power industry? Steele: The global nuclear power industry is a major contributor to the electrical needs of the world. Though generation by nuclear reactors has primarily attracted attention through the reactor accidents at Three Mile Island and Chernobyl, nuclear power continues to quietly and safely provide power to a growing and power-hungry world population. As of March 2008, 30 countries were operating 439 nuclear power reactors. Nuclear power plants provided about 15 percent of the world?s electricity production in 2007. France leads the world in nuclear utilization, with 77 percent of its power coming from nuclear plants. And Lithuania, Slovakia and Belgium each derive more than 50 percent of their power needs from nuclear plants. For much of the developed world, nuclear generation has already been contributing significantly to the supply of electricity. Additionally, 34 new nuclear plants are under construction in 14 countries. Leading the rush to build new nuclear generating plants are China, Russia and India. Each of these countries is building six new nuclear power plants. These 18 plants, totaling almost 12,000 MW of generation capacity, will require about 7.25 kt (16 million lbs) of U3O8 for their initial fuel load and will consume about 2.45 kt/a (5.4 million lbs/year) for the rest of their operating lives. The rest of the world, outside of the United States, has used nuclear power as a viable and economic generation alternative since the commercialization of utility nuclear reactors. And current activity supports the strong future of the nuclear alternative internationally.

Jan 1, 2008

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008