Search Documents

By K. T. Menzies

This report documents laboratory and in-mine analyses of diesel exhaust pollutants carried out to assess the fate of potentially reactive species in the mine environment. Specifically, the concentration of stable compounds including carbon monoxide and carbon dioxide, and potentially reactive compounds including nitric oxide, nitrogen dioxide, sulfur dioxide, aldehydes, formaldehyde, acrolein, formic acid, odorants, particulates, soluble sulfates, and polynuclear aromatic hydrocarbons were determined. The concentration and mass emission rates of these compounds were measured in the laboratory under three engine speed and load conditions and with three exhaust control conditions, i.e., none, catalyst, water conditioner. Once calibrated, the engine was installed in the Bureau of Mines Safety Research Coal Mine and the concentration of exhaust pollutants measured at several distances downstream (inby) of the engine. Laboratory results confirm the relatively small effect of exhaust control devices on most pollutants under engine conditions of low speed and load. At higher engine speed and load, the catalyst is more effective in controlling many pollutants. The in-mine data indicates that during residence times, which are typical for miner/exhaust contact, most diesel exhaust pollutants do not decrease in concentration. The obvious exceptions are nitrogen dioxide, sulfur dioxide and formaldehyde. The concentration of these pollutants is reduced by up to 75 percent in five minutes. The lack of increase in levels of obvious reaction products indicates that surface loss may be a major sink for these pollutants.

Jan 1, 1980

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By Sheridan A. Glen

As the Federal government along with individual states continue to grapple with the job of refining a comprehensive energy policy, coal continually stands out as an energy source which heralds a combination of old and new capabilities like an energy planners prophecy, but which is plagued with serious environmental constraints. To determine what level of coal utilization is ultimately possible for states East of the Mississippi, whose high sulfur content coal presents the most paramount of challenges, one must consider product availability, via existing transportation modes, the developing industrial markets and the ability of coal to meet the challenge of becoming an environmentally acceptable fuel. Gasification is emerging as a form of utilization, which during the next twenty years stands a good chance of being able to meet the challenge of making coal an environmentally clean, easily transport-able and usable fuel. It can be argued that, of all the potential ways of utilizing high sulfur coal, coal gasification is perhaps the most expensive, the most financially risky and carries environmental liabilities of its own. Synthetic gas and oil markets will undeniably be a function of price and demand, which, for the purposes of this paper, I'm assuming will begin to merge in the late 1980's and into the 1990's. This is also presuming that public utility commissions will allow favorable price structure ruling so that gasified coal products can be rolled into their respective rate base, much the same as synthetic natural gas from petroleum by-products are currently being priced. The comparative economic markets of coal to gas pro-duct have plenty of time to mature. There is an approximate twelve-year lead time needed to bring coal gasification plants on line which will be able to compete in the market place for natural gas and oil customers.

Jan 1, 1977

By G. L. Oldright

By means of a technique developed in cooperation with the Eagle-Picher Mining & Smelting Co. and outlined in the first report of this series (R. I. 4333 ), it was possible to take many thermocouple readings with base-metal couples at temperatures over 2300° F with unsupported protection tubes for over half the lengths of the Henryetta retorts. -This technique made it possible to avoid the use of the usual optical pyrometer, which gives temperatures dependent upon the luminosity of the flames, and which is not conveniently usable to read temperatures for the lengths of the retorts from the front of the furnace. The temperatures of the retorts themselves were necessary in order to set upper limits for safe operation; the lower limits of operating temperatures are set by the zinc content of the retort residues. The zinc content left in the retort residues for various sections of length also varies with retort temperatures rather than with flame temperatures. The variations in temperature along the retort can then be used as guides to distill more zinc from the residues, to avoid fluctuations in the rates ,of flow of zinc vapor into the condenser and to employ lower temperatures if such rates become high enough to cause losses of uncondensed zinc.

Jan 1, 1948

By Donald Bruce, Alex Reeb, George Filz, Wesley Schmutzler, Mitsuo Nozu

"One million seven-hundred thousand cubic yards of deep mixing were installed to support an elevation raise of an earthen levee known as LPV 111, which is located in east New Orleans. The deep mixing was done by two contractors using somewhat different technologies, but producing elements of the same size. As part of the quality control and quality assurance program, 507 deep-mixed elements were cored and 5,082 specimens were strength tested in unconfined compression. This paper presents data from the coring and testing program. Very high percentages of the core run lengths were recovered, except during one period for one mixing technology. The coring methods are described, and reasons for the isolated episode of low recovery are discussed. The strength data show that the specification acceptance criteria were satisfied. Statistical parameters of the strength data are provided, and trends between strength and the following factors are discussed: depth, soil type, binder factor, and project-specific experience. Photographs of longitudinal cuts of core specimens are presented. Important lessons learned from this unusually large project are described.INTRODUCTIONThe Lake Pontchartrain and Vicinity Hurricane Protection system included a project known as LPV 111, which is an approximately 5-mile long segment of levee and floodwall located in east New Orleans along the Gulf Intracoastal Waterway and adjacent to Bayou Sauvage National Wildlife Refuge (Cali et al. 2012). The majority of the project consisted of a raise of an existing earthen levee from an existing crest elevation of about 18 ft to a new crest elevation of about 28 ft. The underlying soils were weak and compressible, providing inadequate support for the raised levee. Ground improvement in the form of deep mixing was selected to provide the necessary stability and settlement control for the raised levee.The US Army Corps of Engineers (USACE), New Orleans District, was the governmental agency in responsible charge of the project, including approval of design, construction, and payment. The lead designer was URS Corporation, and the general contractor was Archer-Western-Alberici (AWA), working in alliance with TREVIICOS South (Trevi), who, together with Fudo Construction (Fudo), performed the deep mixing.As part of the quality control and quality assurance program, over 500 production deep-mixed elements were cored, the cores were carefully logged, and over 5,000 unconfined compression tests were performed. In addition, selected specimens were carefully photographed before and after longitudinal saw cuts to expose the interior of the specimens. This paper provides a summary of the coring and testing performed on the production deep-mixed elements."

Jan 1, 2015

By T. S. Washburn

THE grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure-killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes are not present. Also, the rimmed ingot has no well defined pipe, as com-pared to the deep pipe on the killed ingots, and there are numerous pri-mary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differ-entiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7-as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined or deep as in the killed ingot of Fig. 1. In killed ingots, pri-mary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By Neil A. Brown

The trona deposits near Green River, in southwestern Wyoming are world class in size and quality. They contain more than 25 times the reserves of the next largest trona deposit at Lake Magadi in Kenya. Based on present rates of production, the Green River reserve should last for more than 500 years. Since their discovery in 1938, the Union Pacific Corp. has been instrumental in the promotion, development and production of soda ash in Wyoming. Union Pacific spent several years drilling the deposits and trying to promote them to chemical companies. In 1947, Westvaco and Union Pacific entered into what became the first trona lease agreement. Today, the Green River Basin leads the world in soda ash production, accounting for about 25% of the world's supply. Green River producers process more than 14.5 Mt/a (16 million stpy) of trona to produce more than 8 Mt/a (9 million stpy) of soda ash. The future for Green River soda ash looks good, with more of the world looking towards the cheaper and higher quality source of soda ash coming from the natural deposits. Production from the Green River deposits should continue to grow as trade barriers and tariffs begin to fall in Europe and energy and environmental costs force the synthetic producers to exit the market.

Jan 1, 1995

By Charles L. Harnes

A mineral pigment is a colored substance dug from the ground, which after treatment can be mixed with a drying oil to form a paint. Not all colored earths, however, can be made into satisfactory pigment. Much depends upon the attractiveness and uniformity of the color and the ease of purification. Mineral pigments are distinguished from chemical pigments by a difference in origin and treatment. Chemical pigments are not found ready-made in the earth but must be synthesized or otherwise obtained from other compounds or elements; for example, cadmium yellow, a chemical pigment, is precipitated from a solution of cadmium chloride, hydrochloric acid, and sodium sulfide.

Jan 1, 1942

By AIME AIME

The Bulletin. The Bulletin of the Institute will be issued hereafter monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates tin? membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will lie: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. Lt is probable that a supplementary session of this meeting, will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the farther discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. It is now reasonably certain that the XCVIIth meeting will be held oil the Pacific Coast, including a. visit to the Exposition at Seattle, and various other points en. route going or coming, depending upon the route and program finally adopted. (lore definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Jan 1, 1909

By S. L. Windes

This report presents physical and petrographic properties of approximately 60 types of rock from operating mines or mineral-investigation projects and supplements Repot of Investigations 4459, Physical Properties of Mine Rock (hereinafter referred to as Part I). The physical properties evaluated include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength (modulus of rupture) Impact touchiness Abrasion hardness Scleroscope hardness Modulus of elasticity (Yourg?s modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1950

By Lisa R. Papandrea, David Chen, Walter E. Kaeck

"Construction of the University at Buffalo’s new School of Medicine and Biomedical Sciences (UB-SMBS) required excavation in variable ground to a depth of more than 40 ft adjacent to the NFTA Metro subway and Allen Street Station. Complicating the building design and construction, the new medical facility incorporates the at grade Station entrance building, requiring a combination of temporary and permanent excavation support structures, a complex sequence of ground support installation, and a mix of shallow and deep foundations to accommodate the large floor spans and concentrated column loads introduced by building over and adjacent to the Station entrance. Excavation and foundation construction was challenged by a stratified soil profile with interlayered and sensitive sands, silts and clays and complicated groundwater regime with perched and regional water tables. Efficient construction required ongoing coordination between the design team and contractor, careful field observation, and construction monitoring in several facets of below grade construction. This paper describes the design and construction of excavation support structures and foundations to manage the variable ground, congested site conditions, and complications of building adjacent and above an active subway station. Use of site instrumentation and monitoring data to provide guidance in construction when unanticipated field conditions arise is illustrated. Lessons learned in installation and sequencing of excavation support, groundwater control and foundation construction are also discussed.INTRODUCTIONUniversity at Buffalo President Satish K. Tripathi heralded the new School of Medicine and Biomedical Sciences (UB-SMBS) as a future linchpin of UB’s downtown campus that will revitalize the area and enhance western New York’s emerging bio-sciences corridor. The $375 Million, 628,000 square foot, eight story building with two basements is expected to house 2,000 faculty, student and staff allowing UB to increase class size from 140 to 180 students. It will be constructed above the Niagara Frontier Transportation Authority’s (NFTA) Allen Street Station, creating a direct connection to Buffalo’s light rail system. The 200 ft x 400 ft site is bounded by Main Street, High Street, Washington Street and the Roosevelt Apartments and adjoining parking lot at the west, north, east and south respectively, as shown in Figure 2. Groundbreaking for the new building was in October 2013 with the facility scheduled to open in early 2017."

Jan 1, 2016

By V. A. James

The new electrolytic copper refinery situated at Copper Cliff, Ontario, has been in operation for over a year and a half. This plant is operated by the Ontario Refining Company, Limited. The associated companies behind the enterprise are the International Nickel ?company of Canada, Limited, the American Metals Company, Consolidated Mining and Smelting Company of Canada, Limited, and Ventures, Limited. The plant was an outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as compactly as possible. Starting anode furnace operations in June, 1930, and electrolytic refining on July 1st of that year, after a record-breaking construction programme completed in only fifteen months, the plant soon settled into its stride and the usual starting-up difficulties were .rapidly overcome. The rated capacity of the plant, namely, twenty million pounds of refined copper per month, has, of course, never been reached, due to depressed business conditions and latterly to the world copper agreement limiting production. It may be said, however, that the present installation has proved its ability to produce in excess of its rated capacity, and with relatively minor additions to plant and equipment that capacity can be doubled. Owing to the severity of the winters, when temperatures of from 20 to 40 degrees below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were rather unusual in copper-refinery construction.

Jan 1, 1932

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By F. Navarro, F. Soto, G. Díaz, E. Jélvez, G. Morales, N. Morales

The increasing availability of tools on the web provides a great opportunity for the research community to boost investigation by accessing computational resources from all over the world. For example, data analytics libraries implemented in languages like Python can be accessed through many open and commercial platforms, therefore providing researchers with a common set of tools or shared datasets. Unfortunately, that is not the case with research in resource assessment and mine planning, where the most standardised tools are commercial applications designed to work on the desktop, but there are not many standard platforms for research. As a result, researchers from different groups often need to start from scratch in order to develop their work, and rarely share implementations details. Similarly, apart from a few publicly available examples, there is a lack of common datasets that are validated and can be used to compare results between different approaches. In this paper, we introduce a platform that provides tools for resource assessment and mine planning, which can be accessed remotely utilising Jupyter Notebooks. In its current version, the platform provides (i) definition and implementation of basic structures for managing samples and models (loading, saving, adding or removing columns, etc.), (ii) definition of experimental and modelled variograms for spatial continuity analysis, (iii) definition of standard interpolation methods in resource evaluation (inverse distance and kriging), (iv) definition of standard problems in mine planning (ultimate pit and precedence constrained production scheduling), (v) generation of 2D standard graphs like grade distribution, conditional means, tonnage-grade, and production plans (vi) a set of datasets, which can be used for case studies, and (vii) a set of notebooks with examples and documentation. In this paper, we introduce the platform and show some examples that illustrate some of the possibilities that it has for research and education in the area of resource assessment and mine planning.

Sep 1, 2021

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

By J. Shanks

A S far back as 1925, Brazeau Collieries, Limited, became interested in .briquetting. This was brought about by complaints from their principal customer that stack losses, due to a high percentage of fine coal in their mine run, were excessive. The Company considered oil spraying of the fines. This, after some experiments and tests had been made, was ruled out as uneconomical and impracticable. When sufficient oil to be effective was put into the fines, it caused the coal in the tender of stoker-fired engines t0 arch over the screw feeder. The Company ultimately placed their problem in the hands of the Re-search Department of the University of Alberta. Experimental work was carried on by this department over a period of more than a year. The results obtained and the experience gained in this research work were conveyed to Brazeau Collieries in a report dated October 31st, 1929, and in a supplementary report dated February 2nd, 1935. Most of the results obtained in experimenting with Brazeau coal are embodied in a brochure, reprinted from the proceedings of the Second International Conference on Bituminous Coal, Vol. 19-24-28, entitled Principles in the Briquetting of Coking and Non-Coking Bituminous Coals, by E. Stansfield and W. A. Lang. All who are interested in briquetting should read this brochure. In the writer's opinion, iris the most important treatise on the subject printed in recent years. The results given in the paper are, of course, those obtained in laboratory investigation. It was pointed out to the writer that it would be most interesting to have such results correlated with those obtained in commercial practice. In this short paper, an attempt is made to do so.

Jan 1, 1942

By R. P. Gardner

Results of work on the development of a phenomenological model for the continuous flotation process using short-lived radioactive tracer techniques for the determination of model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross flow finite state (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques necessary to extract the model parameters have been developed as have the necessary nonlinear search methods. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A microcomputer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation system for the two systems mica ore and coal.

Jan 1, 1985

By Fidelis T. Suorineni

The Ashanti mine, located in Obusai, Ghana, West Africa, has been in production for over 100 years, and is currently the second largest single gold producer in Africa. The mine covers a concession area of 434 square kilometers with four main ore types: the quartz vein type, disseminated sulphide type, supergene sulphides and transition ore, and granitoids stock works (visible gold and quartz veinlets). Various mining strategies and methods have been employed for the mining of the narrow-vein ore at Ashanti. In recent years, the mine owner: Ashanti Goldfields Company Ltd. has embarked on a mine-wide expansion program to boost production to a target of one million ounces per annum. With the rapid depletion of its high-grade ore, a suitable mining method was required to produce a high tonnage at low cost to meet production objectives. This paper discusses how the Ashanti mine applied Canada experiences in mining technology to boost production, and the impact that the differing geological settings between the two countries had on the stope performance at the Ashanti operations. Experience developed at the Ashanti mine led to innovative modifications for stope layout and design methods in relatively poor ground conditions.

Oct 1, 2001

By Daniel C. Boteler

Five lignites from the northern Great Plains province were carbonized at temperatures from 500° to 1,000° C in a bench-scale unit. A replicated Greco-Latin square experimental design was employed to allow testing of four independent variables at five levels. Independent variables investigated were temperature, source of lignite (mine), weight of charge, and moisture content of charge. Dependent variables were char yield, tar yield, light-oil yield, tar plus light-oil yield, carbonization gas yield, and carbonization gas heat yield. An analysis of variance indicated that, at the 99-percent confidence level, the independent variables of carbonization temperature, source of lignite, and weight of charge were significant for yields of char, tar plus light oil, and carbonization gas, whereas moisture content was only significant for carbonization gas yields. At the 95-percent confidence level, moisture content significantly influenced the carbonization gas heat yield per pound of lignite charge and the yields of dry tar plus light oil. All dependent variables were determined on a moisture- and ash-free basis. Multiple regression equations for predicting seven different factors of carbonization yields as functions of carbonization temperature and initial composition were developed using computer techniques. Equations for yields of char, tar plus light oil, and carbonization gas were compared with equations previously developed by others at the 500° C level.

Jan 1, 1970

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974