Search Documents

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d'un tunnel excavé dans une région de construction d'une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s'ensuit que l'état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l'état de contrainte initiale.

Jan 1, 2003

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By Frank E. Cash

As a part of its safety program the United States Bureau of Mines has fostered the development, use, and improvement of portable electric mine lamps. Although there is still need for better illumination in mines and the replacement of open lights has been slow, improvement in electric cap lamps and increase in their use indicate one phase of recent progress toward safer and more efficient mining This report is the result of a recent survey of electric-lamp installations in the Alabama mining; district; it shows the misuse, increase in use, and relation to certain classes of accidents of these installations.

Jan 1, 1935

By Scott Ellenbecker

Mining has evolved in recent years, taking steps forward in the way that the industry is considerate of the environment and the communities in which it operates. Technology plays a major role in that evolution. Osisko Mining?s Osisko Mine near Malartic, Quebec is developing a new way of doing business. One manager said, ?We are building the Osisko culture,? but the company is doing many things that could become industry changers. Much of the change is driven by mine ownership and management to offer a better workplace and better community relations. Mining equipment manufacturers are changing, too, by engineering products with more operator comfort, fuel economy, ease of maintenance and more cleanly designed machines. And for those drills working close to communities, smaller bore sizes and sound retention are just two changes for the better.

Jan 1, 2012

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

By H. G. Rushton, A. S. Romaniuk

"The opening chapter of this volume, by A. Ignatieff, places in perspective Canada's coal resource base as part of the world scene. This chapter will focus on the Canadian scene.Units of measurement in this report are in the International System of Units (SI) as approved for official use by the Canadian Standards Association and Metric Commission Canada. These units have been adopted by the Mining Association of Canada and the Coal Association of Canada. To assist with the shift to metric units these two associations have published ""Metric Practice Guide for the Canadian Mining and Metallurgical Industries"", 1978(1J, Appendix ""A"" lists some useful conversion factors along with SI prefixes. The last official assessment of Canada's coal resources and reserves was done by the Department of Energy, Mines and Resources and presented in Report ER 79-9 ""Coal Resources and Reserves of Canada"", published in December 1979 and authored by H.U. Bielenstein, L.P. Chrismas, B.A. Latour and T.E. Tibbetts(2). The Geological Survey of Canada has a continuing project concerned with coal resource assessment as does CANMET, whose concern is with coal reserve assessment and coal quality. As well, Alberta's Energy Resources Conservation Board (ERCB) has a continuing assessment program for coal in Alberta and publishes an annual reserves report, the current issue of which is cited as reference No. (3). The difference in resource and reserve terminology as used by EMR and ERCB has a major effect on derived tonnages for Alberta. This difference will be discussed later. In 1982 the Department of Energy, Mines and Resources produced a map titled ""Canada-Coal""<4J which outlines coalfields and illustrates coal import and export movements for the years 1981and1980. A copy of this map is contained in the map pocket of this publication. Two other resource assessment reports are noteworthy, the first is ""Coal Resources of Southern Saskatchewan: A Model for Evaluation Methodology"", by J.A. Irvine, S.H. Whitaker and P.L. Broughton<SJ which is one of the major outputs of a joint federal-government study of southern Saskatchewan's lignite deposits. (Another output from this same study' is the Geological Survey of Canada's SASCO file, a computer processable file holding borehole and coal quality data.) The second is ""Deep Coal Resources of the Interior Plains, Estimated from Petroleum Borehole Data"", by G.D. Williams and M.C. Murphy(6) which identifies coal resources from nearly 4,000 petroleum exploration boreholes distributed uniformly over an area spanning Manitoba, Saskatchewan, Alberta and British Columbia."

Jan 1, 1985

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010

By A. R. Leach

Anomalous mining conditions can be described where the level of hazard is increased relative to normal conditions within a mining area. Normal conditions would be those defined as a Ground Control District in a mine’s code of practice, and for which mine standard support layouts are generally developed. It has been found that up to 80% of fall of ground accidents occur where anomalous mining conditions exists, typically in the vicinity of geological weaknesses. These areas require specific attention to ensure they are readily anticipated and identified and that appropriate strategies are used to reduce the hazards associated with them. As part of SIMRAC project GAP 607 checklists to aid identification and best practice mining methods were identified for a range of geotechnically anomalous conditions.

Jan 1, 2003

By George H. K. Schenck

In this decade of the 1.970&apos;s it is forecast that eight billion cubic yards of rock will be excavated from 400, 000 miles of new tunnels, drifts and other underground workings in the western world, according to estimates in a report of the Organization for Economic Cooperation and Development (OECD). It is expected that the cost of this work will be in excess of $54 billion in constant 1970 dollars. Most of this underground excavation will be in mining -- 97% of the tunnel length and 89% of the volume - -the balance in construction. In addition to this huge excavating task, in the 18 developed nations of OECD, will be projects in the Communist Bloc and in the developing nations. Underground excavation requires the successful completion of three principle activities: A. Break -- to free rock from the solid work face. B. Remove-- to clear the work area of broken rock. C. Support -- to assure stability of rock surrounding the underground excavation and to eliminate risk of rock collapse. In today&apos;s fully mechanized excavation systems, continuous miners, roadheaders or tunnel borers, (A) break the rock loose from the face, and (B) remove broken rock with their mucking devices and load it onto belt conveyors, mine cars, trucks, or any other appropriate haulage system for disposal. Such operations contrast to the more complex, intermittent systems employed when

Jan 1, 1974

Jan 1, 1994

By ALBERT E. HALL, Arno C. Fieldner, Alexander L. Field

As a safeguard against excessive clinker troubles, specifications for the purchase of coal can be drawn to include the "softening" or "fusing" temperature of the ash. The value of such information has been recognized by the Bureau of Mines and has induced the bureau to investigab~ laboratory methods of determining the fUSIbility of coal ash, and the bearing of the results on clinker formation in fuel beds. The bureau realized that the fusibility of a mixture of oxides and silicates snch as is comprised in coal ash ,'aries according to the conditions under which tests are made, and that in the absence of any generally accepted method, no agreement is to be expected among tests made in differ«:-nt laboratories. Indeed, Marks a has recently called attention to differences as great as 3900 C. that were obtained with the same sample of ash by two different laboratories. Therefore if a fusion-temperature clause is to have any place in specifications for coal, a standard m('thod of t('sting should be adopted in order to insure comparable results by different laboratories and to obtain the softening or fusing temperature of the ash unde:'r conditions similar to those of a fuel bed. After a consistent method has been devised for obtaining comparable:' results at different laboratories, there will remain the correlation of these results with those from the burning of coal in furnaces before the value of fusibility tests in coal specifications can hE' finally determined.

Jan 1, 1918

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620&apos;s. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

The suitability of char from Yallourn brown coal as a filler for carbon electrodes used in the aluminium smelting industry has been assessed on the basis of the specifications usually laid down by electrode manufacturers for petroleum coke fillers. The purity specifications can be met by a simple acid leaching of the coal before carbonization. The true density of char produced at 1200&#176;C is within 5 per cent of the specification figure, but the bulk density of char obtained from as-mined coal is only half that specified for petroleum coke.Although this can be increased to three-quarters of the specified figure by briquetting the coal before carbonization, further increases would be very difficult to achieve, as the remaining shortfall in density is due to an extensive microporosity developed in the particles of char during carbonization.

Jan 1, 1970

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By Thomas Prietl

The use of gas stirring systems through the furnace bottom is common for anode and holding furnaces in the copper industry The first implementation of a gas stirring COP KIN® system in a Peirce-Smith converter was performed at the New Boliden smelter, Rönnskar, Sweden. In addition to other benefits, a decrease in process time and a decrease of the oxygen content in the blister copper were observed. To determine the effects of the gas stirring system and the process endpoint, an optical production control ?Semtech OPC system? was used. The light emission of the converter flame as an optical process parameter provides qualitative on-line process information, and is also used for endpoint determination of the slag making process, on-line control of iron content in white metal, quality control of slag etc. The results, benefits and risks of using the COP KIN® and OPC system for a Peirce-Smith converter are reported.

Jan 1, 2005