Search Documents

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

Samples weighing 0·5 g are decomposed with hydrofluoric and other acids. Most elements are extracted ftom the acid, aqueous solution by Alamine 336 (tricaprylyl tertiary amine) and thorium is determined in an aliquot taken from the aqueous phase by means of its reaction with arsenazo III. Concentrations down to 4 p.p,m. may be determined at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

The reality of rising electrical power costs and the haunting prospect of decreasing electrical power availability are a threat to the growth of new projects and expansion programmes that could negatively affect the sustainability of mining operations. These threats require the adoption of effective power saving measures aimed at three principal objectives: the elimination of wastage, the reduction of power usage particularly during peak demand periods and, more importantly, improving the efficiency of high power-demand processes. It is reasonable to assume that the greatest impact will be achieved by concentrating on those processes that are large electrical power consumers. For Anglo Platinum operations, mine ventilation and, currently to a lesser extent, mine cooling are two continuous processes that fall in this category. It is estimated that these may consume fifteen to thirty-five per cent of the power delivered to the shaft head-depending on the shaft's design. Mine ventilation systems suffer from inherent, historical inefficiencies that lead to excessive power consumption. Air cooling systems are designed to be energy-wise in terms of modulating refrigeration plant operation to meet the underground requirements while maximizing use of 'free' cooling from surface conditions. Currently about ninety-five per cent of the refrigeration capacity used in Anglo Platinum mines is dedicated to surface bulk air coolers. The net thermal efficiency of these systems is compromised as mines expand in depth and on strike. Looking to the future, this practice will be complemented by more energy demanding underground cooling tactics requiring considerably higher electrical power consumption per unit ton produced. To counter this increase in power consumption, more energy-efficient systems and advantageous transient strategies such as thermal storage and the use of ice-on surface and possibly even underground-are being considered. This paper describes work currently undertaken and planned by Anglo Platinum operations to reduce power consumption by main fans during off-shift periods, the associated efforts currently introduced to reduce underground air leakage, the possibility of introducing more efficient auxiliary ventilation systems, the feasibility of thermal storage, and a brief look at energy recovery system as a means of countering the anticipated power demand associated with underground cooling. Keywords Mine ventilation, mine air cooling, energy efficiency, chilled service water, energy recovery, air wastage, fan selection.

Jan 1, 2011

By J. F. Curtis

In the synopsis, the author concludes that ?high levels of seismicity do not coincide with high rockburst rates?. Implicit to an appreciation of this statement is the necessity of a common understanding of what is understood by the terms: ?high level of seismicity? and ?high rockburst rates?. With respect to the former term there is no difficulty in that the level of seismicity is traditionally measured in terms of the Richter Scale. The latter term however presents a problem in that the author defines it as a particular sort of seismic event?viz: ?Rockburst? is understood as a seismic event that causes damage to an underground excavation with subsequent injury, loss of material/equipment or production shifts? (p. 322). No scale is given of the amount of: ?excavation damage ?level of injury ?material/equipment loss ?production shifts lost whether separate or cumulative, for a particular seismic event to be classified as a rockburst. A further difficulty arises in that in common usage the words ?rockburst?, ?seismic event? and ?earthquake? are all used to describe the same event.

Jan 1, 1999

By A. E. Tercan, D. Mamurekli

Ordinary kriging on the assumption of a gaussian error distribution and indicator kriging were used to derive the probability that a given calorific value would or would not be exceeded by coal from an area of a deposit. The two techniques led to similar probability maps despite local differences; the lack of an absolute reference makes it impossible to judge which method is better for this particular application

Jun 19, 1905

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

U.S. Borax’s mine in California’s Mojave Desert is the source of nearly half the world’s supply of refined borates. These minerals are used in hundreds of products, including essential plant nutrients that increase crop yield and quality, and safe building products that protect homes from insects and the elements. Borax’s workforce is also safe. In fact, it is among the safest in the nation. In 2003, the company was recognized by the U.S. Mine, Safety and Health Administration (MSHA) for achieving the best safety record among large U.S. mining operations. It was also recognized by its parent company, Rio Tinto, for achieving the best record among its nearly 80 worldwide mining operations. Borax’s safety performance is five times better than the national average. And its workforce recently achieved more than two million hours without a lost-time injury.

Jan 1, 2004

By Edgar Carlos García Flores

El presente texto señala al Perú como modelo de sistemas de explotación minera para Bolivia -en tanto desarrolle, prepare y explote las minas con calidad y así incrementar la producción de sus operaciones mineras. Asimismo, describe los procedimientos idóneos para seleccionar las tablas geomecánicas, la ingeniería de explosivos, equipos de acarreo y los elementos de sostenimiento adecuados para las excavaciones subterráneas con el objetivo de tener operaciones de calidad, seguras y óptimas.

Feb 1, 2015

By Javier Rodriguez

Adaptive re-use of existing structures in urban environments has become very common due to lack of available space in our cities and requirements for increased structural capacity. Often, it involves retrofitting existing foundations to support increased loading. In such cases, Engineers face the need to review existing deep or shallow foundations for their true load carrying capacities in order to determine the required magnitude of retrofit work, if any. To accomplish this, the engineer must track down and cull through the existing construction documentation to determine what was actually constructed, complete an investigation to confirm these conclusions, possibly sample the foundation elements for strength properties, and on occasions complete non destructive or full scale load testing of indicator elements. This paper describes the typical procedure followed by the authors for design of retrofit schemes for existing buildings in the Washington DC metropolitan area. Three case histories are presented that illustrate various issues encountered during design.

Jan 1, 2006

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By R. Jolicoeur, J. F. Jackson, M. A. Green

"The design, construction and commissioning of Kiena Gold Mines Limited's new mill was completed in 15 months ending in September 1984. Rated at 1250 tonnes per day the mill incorporates the latest innovative technology such as semi-autogenous grinding, carbon in pulp, pressure stripping and induction furnace refining. The mill is housed in a pre-engineered building with the leach tanks and thickeners located outdoors in spite of the intense winter cold. 1.0 INTRODUCTION AND HISTORYThe operations or Kiena Gold Mines Limited are located in Dubw1sson Township, approximately 10 Km west of Val d'Or, in the Abitibi region northwestern Quebec. Comprised of 59 mining claims covering 1214 hectares, a large portion of the mining property is overlain by the waters of Lac de Montigny. Sometime between 1911 and 1914 Barney Parker discovered gold in a shear zone on an island in Lac de Montigny that now bears his name. The first shaft the Parker Shaft, was sunk in 1936 from the island to a depth of 136 meters but owing to the known veins being of limited extent and the onset of the Second World War operations were terminated in 1940. In the early l960 1 s exploration drilling indicated an orebody of 4,500.000 tonnes at 6.3 grams of gold per tonne. A causeway was built to link the island to the mainland in 1963 and a new 3 compartment shaft was sunk to 403 metres. The orebody was further delineated and the ground conditions within the orebody and surrounds were evaluated.At the end of 1965 the property was placed on a care and maintenance basis as a mining operation would be marginal with gold selling at $35 per ounce."

Jan 1, 1986

By Ta M. Li

How will phosphate producers in southeastern Idaho fare with growing governmental regulations and environmentalism of the late 1970's? With a similarity that is reminiscent of the battles between the coal industry and environmental-conservation groups earlier in the decade, Idaho's future growth and a nation's need for phosphate fertilizer products remain uncertain. The catalyst that brought the issue to the forefront was the preparation of an Environmental Impact Statement (EIS) addressing the development of phosphate resources in southeastern Idaho. Although the final EIS was published in August 1977, resolution of rational and orderly growth in this potentially vital region remains stifled as Secretary of the Interior Cecil Andrus virtually "sits" on it.

Jan 1, 1978

By Oliver C. Ralston

The nonmetallic minerals work of the Bureau of Mines started with the organization of the Mineral Technology Division in 1912. A special experiment station devoted to the mining, preparation, and processing of nonmetallic minerals was established in 1923 at New Brunswick, N. J., and concentration problems on nonmetallic minerals of all kinds also were studied at the Mississippi Valley Experiment Station at Rolla, Mo. In July 1936 the Nonmetals Division was organized, and in May 1937 the Nonmetallic Minerals Experiment Station at New Brunswick, N. J., was moved to and made a part of the new Eastern Experiment Station at College Park, Md. At present the Nonmetals Division operates at three points: The Eastern Experiment Station, College Park, Md., which is headquarters for the division chief; the Southern Experiment Station, Tuscaloosa, Ala.; and the Northwest Experiment Station, Seattle, Wash., where coal washing and preparation studies are included with those on nonmetallic minerals. Sand, gravel, and aggregate work is carried on by the Mining Division, as sand and gravel preparation are intimately associated with mining methods. The Economics Branch of the Bureau of Mines also prepares occasional papers on nonmetallic technologic subjects in connection with the presentation of statistics on a particular industry and reviews of the mineral industry in foreign countries for use in the monthly publication, "Mineral Trade Notes."

Jan 1, 1937

Steven F. Leer, president and chief executive officer of Arch Coal Inc. will be the master of ceremonies for the 12th Annual National Mining Hall of Fame Induction Banquet. The black-tie (optional) affair will be held at the Adam’s Mark Hotel on Sunday, Oct. 10 in St. Louis, MO. Six legendary leaders will be inducted at the ceremony. They will join 145 mining greats previously honored in the annual ceremonies. R. Joe Wagner, vice president for exploration and chief geologist of The Doe Run Co., St. Louis, will be the evening’s keynote speaker. His father, Richard Edwin Wagner (1898-1979), was inducted into the National Mining Hall of Fame in 1998 at the banquet in Phoenix, AZ.

Jan 1, 1999

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

Investigation of the Effect of N-Substituents on Performance of Thioureas as Special Collectors for Copper Sulfides by ab Initio Calculations

Sep 13, 2010

By F P. Hao

Organo-sulphur-based collectors (eg xanthates, dithiocarbamates and dithiophosphates) are widely used in the flotation of sulphide minerals. Xanthates (ROC(=S)Sû), for example, adsorb strongly at sulphide mineral surfaces, in a reaction that is electrochemically coupled with the reduction of dissolved oxygen. One of the oxygen reduction products, hydrogen peroxide, reacts directly with dissolved xanthate, leading to its oxidative decomposition. Experimental work has been conducted, using ethyl xanthate, to understand the molecular mechanism by which hydrogen peroxide reacts with xanthates. A number of degradation products have been identified, some of which have not been reported previously. This oxidative decomposition reaction pathway is discussed in the broader context of xanthate decomposition in flotation systems. One of the identified ethyl xanthate decomposition products, ethyl perxanthate (ROC(=S)SOû), has been observed in the process water of a number of mineral processing operations. The interaction of this molecule with goethite (α-FeOOH) particles, typical of that found in tailings dams, has been studied in more detail using attenuated total reflectance (ATR)-FTIR. The ethyl perxanthate molecule has been found to coordinate to iron (FeIII) at the goethite surface, and undergo a surface-catalysed decomposition process. In the presence of both PbII and goethite, a ternary surface complex is formed, where ethyl perxanthate is coordinated directly to surface adsorbed PbII atoms. The results obtained give some insight into the environmental fate of ethyl xanthate in tailings streams, and a basis on which to consider the environmental importance of such species in tailings dams. Strategies for the destruction of residual xanthate levels in waste water streams are discussed in terms of the likely reaction products.

Jan 1, 2002

By Donald J. Hallbom

"While pipeline hydrotransport is often the most economical way to transport large volumes of mineral concentrate, tailings, or fine ore slurry over long distances, it is in mountainous terrain that pipelining becomes particularly attractive. These areas are often remote, with limited existing infrastructure and few potential users willing to share in the cost of new infrastructure. The rugged terrain makes the construction of railways or roads suitable for haul trucks difficult and expensive. The elevation difference between the mine and the terminal means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. As a result, numerous pipelines have been built, or are being considered, in mountainous regions around the world including: Tasmania, New Guinea, China, Madagascar, the Rockies of North America, and the Andes of South America. However, there are technical difficulties that need to be overcome in the design and operation of mountain pipelines that do not affect pipelines on more level terrain. This presentation reviews some of these difficulties and methods used to overcome them.INTRODUCTIONPipeline transport of solid-liquid slurry (“hydrotransport”) is an important and cost-effective means of transporting large volumes of solids over long distances, especially from a single supplier to a single user (e.g., a concentrator to a port, a concentrator to a tailings dam, or a coal mine to a power plant). Pipelines are generally found to be more economically attractive than alternate transportation methods (e.g. trucking, rail, conveyors, shipping, or some combination) over the life of a project (Aude et al. 1974).Hydrotransport systems have been built in a variety of terrains, but it is in mountainous regions that pipelining becomes particularly attractive. These regions are often remote and generally do not have existing transportation infrastructure (roads, railways, navigable rivers). There are few potential users (e.g., farmers, other mines, forestry companies, etc.) who may be willing to share in the cost of new infrastructure. The rugged terrain makes the construction and maintenance of railways or all weather roads suitable for large haul trucks difficult and expensive. Mines tend to be higher than the receiving terminal (e.g. a port). This means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. Pipelines are easier to construct than roads and railroads in these areas for several reasons, including:"

Jan 1, 2006

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

The Stability Graph Method is widely used in Canadian underground hard rock mines for open stope support design and is frequently used in the mine planning phase to assess the viability of stope geometries and to determine maximum permissible spans. The Method is well accepted due to its simplicity and suitability to a wide range of mining methods requiring the use of sublevels to access and extract the mining blocks. While this Method is reliable in situations where the maximum induced tangential stress creates adequate compressive stress keeping the face in a state of confinement, the Method fails to reflect the effect of low confinement caused by lower compressive stresses and instances where tensile stresses are developed. In this paper, a new Rock Stress Factor, A?, an update to the original Rock Stress Factor, A, is proposed, which will reflect the impact of low confinement or overstress regime on critical face stability. Two case studies, based on two Canadian operating gold mine shows that using the new Rock Stress Factor A? to predict the stability of stope hanging-wall and footwall gives better agreement with the CMS survey results, compared with the prediction using the original rock stress factor.

May 1, 2011