Search Documents

By E. H. Cho, B. Conner

Three sulfide minerals, chalcopyrite, sphalerite, and pyrite, were leached using a bioleaching mode and an electrobioleaching mode. The former mode was used to leach the minerals with the bacterium A. ferrooxidans in a bioreactor. In the latter mode, the leaching of the minerals was performed in a combination of a bioreactor and an electrochemical cell. In this set-up, the solution was circulated between the bioreactor and the cathode compartment, the two reactors were in series, and the cell was operated intermittently. The mechanism is such that an increase in Fe(II) concentration, which is a nutrient of the bacteria, by electrochemical reduction of Fe(III) would increase the bacterial population and in turn would accelerate the leaching of the mineral. It has been found that the electrobioleaching of chalcopyrite is an improvement over the bioleaching with respect to the fact that leaching conversion is higher and a high level of Fe(II) concentration can be maintained. However, the electrobioleaching of sphalerite does not show any improvement over bioleaching. The electrobioleaching of pyrite is similar to that of chalcopyrite, and this has potential to be used in applications such as coal desulfurization and pretreatment of refractory gold ore in heap leaching where fine gold particles are entrapped inside pyrite particles.

Jan 1, 2006

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under development since. 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1998

Atlas Copco Construction and Mining Australia identified a number of issues in regard to the skill levels, labour turnover and productivity of our service technicians. In 1994 we were experiencing a labour turnover rate of 42 per cent per annum amongst our technicians. Exit interviews were held with each individual and one of the major areas of dissatisfaction was the degree of product training provided on our equipment, compared to what is required to be competent across the range of our products. These tradespersons were prepared to accept the reduced remuneration that an OEM offers, for the benefit of comprehensive, professional training that, in theory, could be provided. The truth is that we were achieving approximately 40 per cent of our target for training hours because of the demands of field service, pre-deliveries, etc. So, the summary was the same as the industry was experiencing at that time because of skilled labour shortages, production demands, etc people were employed and thrown in at the deep end. A recipe for failure that will be successful every time.

Jan 1, 1998

By George A. Page, Hewitt Wilson, Vance S. Cartwright

"Purpose of InvestigationThe process of removing solid material from liquid suspensions has been studied at the Northwest Experiment Station, United States Bureau of Mines, in cooperation with the University of Washington, as part of a general program to investigate the dewatering of Pacific Northwest plastic kaolins, which is difficult by ordinary filter-pressing methods. The present paper is a progress report of the work began by Vance S. Cartwright in 1928 and continued in 1931 and 1932. Spray evaporation is believed to be valuable for the following classes or grades of clay and clay mixtures:(1) Highly colloidal, plastic-type clays, which release their mechanically attached water with difficulty; (2) clays prepared for shipment in pulverized or powdered condition; and (3) synthetic, ceramic, porcelain, and tile mixtures prepared as aqueons suspension, dried and pulverized before molding. Dilute suspensions can be dewatered by spray evaporation to produce concen-trated casting slip or plastic clay with a lower water content.The most common dewatering method used in preparing powdered kaolin for the market comprises the following steps: Reduction of the water content by filter-pressing from approximately 75 percent in the thick ""slip"" condition to about 30 percent in the condition; further reduction of the water in the filter-press cakes by heat to about 5 percent; and pulverization of the dried cakes in hammer or dust. These three steps can be simplified to a single process by spray evaporation."

Jan 1, 1935

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By Henry John Luna Córdova

El presente trabajo describe el proceso de gestión de calidad en la administración de los derechos mineros a través de la automatización de procesos desarrollados por el Instituto Nacional de Concesiones y Catastro Minero (INACC) organismo público descentralizado del Sector Energía y Minas que administra el Procedimiento Ordinario Minero para el otorgamiento de Concesiones Mineras, el Catastro Minero Nacional y la distribución del Derecho de Vigencia a escala nacional. Entre otras funciones de dicha institución está la creación de una serie de base de datos numérica, que le han permitido optimizar dichos procesos en calidad. Así como en el aspecto de la administración del Derecho de Vigencia y Penalidad, se creó el software para automatizar sus procesos y efectuar el cobro respectivo en las entidades del sistema financiero nacionall. Finalmente en el aspecto catastral, se generalizó el uso de coordenadas UTM (PSAD56) para identificar los derechos mineros, asimismo, se crearon los parámetros de transformación de coordenadas WGS84 a UTM.

Jul 31, 2003

Most mining operations have been happy to live in blissful ignorance of what their equipment is really capable of. Shareholders have been shown increasing tonnes output per employee (due to rationalising employee numbers). It is now known that the best practice for large mining trucks is 52 per cent higher than average or best practice for excavators is 41 per cent higher than average, or 38 per cent in shovels or 35 per cent with draglines, etc. The data is available. The bell curve of performance is flat. Substantial underperformance is rife. If you are working in or supplying equipment or services to one of the majority of operating mines that donÆt achieve best practice surely you want to know why. Or maybe you donÆt? For many mining people this sort of knowledge could be dangerous to their career so keeping the MD or CEO in the dark is a good option. Many suppliers donÆt want the performance of their equipment benchmarked? Mining consultants donÆt have the data so they are happy to keep guessing. Unfortunately, many Business Improvement or Business Excellence projects are about ticking the participantÆs æcareer boxesÆ. The first step to capacity utilisation is knowing what the capacity is. Even then people and culture will get in the way. People are the biggest hurdle to capacity utilisation. This paper will discuss what the mine of the future (and today) will need to do to utilise the productive capacity of its assets. It is not just benchmarking. It is not just automation. It is not just technology. It is about engaging those people who impact on equipment performance; right from the operator up to the Mine Manager. Doing it better involves a process to facilitate change and a culture which says it is OK to try even if you are wrong.

Jan 1, 2009

By P. Grainger, P. G. Kalaugher

Paper presented at conference and first published in preprint volume of: Risk assessment in the extractive industries, held in University of Exeter, 23-24 March 1994. London: IMM, 1994. Large, unpredicted ground movements resulting from open cast or underground mining present risks to the safety and economy of extractive industries. As large, sudden failures are usually preceded by small displacements at a much slower rate, the detection and monitoring of these minor changes to the ground surface provides a means of assessing the risks. It is recommended that a visual approach is often preferable to surveying or fixed instrumental measurements. An optical system has been devised, incorporating a 35 mm camera, which allows an immediate comparison on site between a colour transparency taken on a previous inspection and the scene it represents. The observer fuses the transparency stereoscopically with the directly viewed scene. The impression is close to that of normal vision except that differences in detail which have occurred since the transparency was taken are immediately obvious, enabling a qualitative assessment of changes to be made on site. If repeat photography is required it can be taken with exactly the same alignment and coverage. The two images are then available for office analysis using simple micro-photogrammetry

Apr 1, 1996

[This Bureau of Mines report presents results of a survey of underground mining equipment and of two demonstration programs showing the feasibility If quieting; a load-haul-dump (LHD) machine and a personnel vehicle. Typical noise levels are presented for the major machine types used in underground mines, along with estimates of the noise overexposure of miners who operate or work near these machines. General principles of noise control are explained, and the application of these principles is illustrated in the description of modifications made to the LHD machine and the personnel vehicle. The noise control package installed On the persona of vehicle lowered its noise level by 14 dBA after 4 months of operation, and inspection of the LHD machine after 2 1/2 years of operation with the modifications showed its noise level 7 dBA lower than that of the unmodified machine. Noise dosimeter measurements indicated that both machines were in compliance with Federal noise regulations for a typical shift.]

Jan 1, 1980

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the 3D surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. Studying the geometrical and temporal relationship between these two signals opens a broad window through which new management techniques become apparent. In this paper we discuss the signal processing techniques used to study these relationships, as well as the related implications for mining. This research was carried out in association with the Chevron Mining underground molybdenum mine in Questa, New Mexico. Some of these new techniques will be integrated into the decision management process at the mine and will provide insight on ore production, draw control, and safe reclamation. The science of signal processing involves the analysis and interpretation of physical processes that vary with time. Two general categories of signals1 are recognized. A continuous signal is a waveform of varying amplitude that is continuous in time (such as a sine wave). A discrete signal is a sequence of quantized values. The independent time variable and amplitude are sampled periodically such that we only know the value and shape of the waveform at the sampling frequency. Displacements measured by a Global Positioning System (GPS) receiver are an example of this. Discrete signals may be studied in the time, frequency, autocorrelation, or wavelet domains. In this paper the amount of ore extracted from the mine and the measured surface displacements are analyzed in the time domain.

Jan 1, 2008

By L. Mpolokeng, J. P. Labuschagne, H. Yilmaz

"An investigation into pillar cutting was carried out at a platinum mine on the western limb of the Bushveld Complex. The focus was on crush pillar design and implementation in order to ultimately improve the compliance percentage for pillar cutting. The major findings from the investigation suggest that the pillar cutting problem lies with the implementation of the design rather than the design itself. Observations of the practical issues underground that prevent good pillar cutting were made. After these issues had been identified, recommendations to rectify these problems and a few other issues identified during the investigation were provided. The recommendations are aimed at improving the pillar cutting compliance and reducing the likelihood of pillar bursts or pillar runs, which will ultimately create a safer mining environment. Paper written on project work carried out in partial fulfilment of BSc. Eng. (Mining Engineering)"

Jan 1, 2015

By R. Armstrong

Due to limited available level ground, Nkomati Nickel Mine cut a weathered rock slope at the base of a mountain spur in order to create a platform for construction of the primary crusher plant and run-of-mine stockpiles. As space is limited around the mining area, ore processing at Nkomati is based on a high reliability of flow of material through the crusher plant, with minimal usage of other and larger designed stockpiles. Evidently, any crusher plant shutdown will render the mine as a whole unproductive and put excessive strain on the medium- to long-term large ore stockpiles, the deposition rates for which are restricted by founding material consolidation requirements. At the onset of the 2012 rainy season, movement was identified on the slope monitoring system and cracks developed on the slope. After a minor failure on the crusher slope an assessment of the slope stability was conducted and a slope management plan recommended, which included deployment of real-time monitoring. An evaluation of the conditions leading to instability was conducted and the likely causes for the failure identified. A full evaluation of the slope monitoring, rainfall, and mining conditions was undertaken and movement triggers were determined. This paper describes the events leading to the development of the failure and the evaluation of the monitoring data to determine a management plan for the failure that allowed for minimal shutdowns of the primary crusher.

Jan 1, 2014

By K. Short

Over the past several years, the mining and minerals market was overloaded with discussions around reviving mature terminologies like distributed control systems (DCS), programmable logic controllers (PLC), and the ?new comers?: hybrid control systems (HCS) and programmable automation controllers (PAC) and, in parallel, which technologies would be more appropriate for mining and mineral processing applications. Ten years ago, a careful comparative analysis would make more sense. Control approaches had very distinctive differences where users needed to choose the right approach.

Jan 1, 2012