Search Documents

By G. M. Kintz

"Methods and costs of rock-dusting bituminous coal mines have been discussed in various publications by the United States Bureau of Mines and others.3 This paper discusses the present methods and cost of dusting at the Swastika mine of the St. Louis, Rocky Mountain and Pacific Co., Raton, N. M.In the Swastika mine the recommendations of the United States Bureau of Mines with regard to rock-dusting are followed at least as well as in any mine in the States of Wyoming, Colorado, and New Mexico. This mine is located at Swastika, N. M., approximately 4 miles west of the town of Raton and is in the Raton coal seam. The mine is rated as gassy and produces approximately 1,000 tons of coal per day.A mining system known as the ""room-and-pillar with cut-offs"" is used which results in recovery of nearly 100 per cent of the coal. The mine employs approximately 250 men.Ventilation is maintained by a Sirocco fan so arranged that the air current may be reversed and exhausting approximately 130,000 cubic feet of air per minute at 3 inches water gauge. This fan is supplemented by two auxiliary fans for emergency use. Three main entries penetrate the hill in a straight line for approximately 8,000 feet. The haulage is through the center entry, which is also used as the intake in conjunction with a two-compartment concrete-lined shaft located at the end of the entries. The main return for 3,000 feet inby the fan is 12 feet wide and 7 feet high. For this distance the ribs have been reinforced by a wall made of coke-breeze blocks plastered over with cement. Solid concrete blocks are used for the top row of blocks of the wall. Steel 10-inch I-beams spaced 40 inches apart center to center are supported on these solid blocks and thus support the roof. The next 1,000 feet inby has the same area, but the cement blocks extend to the roof, as no crosspieces are needed. The airways are kept clean and well rock-dusted.A rather unique system is used to handle gas feeders along the intake and haulage entries. There these feeders occur in the roof or where gas is apt to collect in high points along the haulage, tin funnels as large as 3 feet in diameter are placed near the roof. From these a 2-inch or other suitable-sized pipe is run into the return through the wall of the nearest break-through. A valve on this pipe line controls the amount of air pulled. These devices keep the high places clear of any gas, even when strong feeders are encountered.Fifteen-ton electric trolley locomotives are used on the main haulage and approximately 30 roller-bearing oars, each having a capacity of approximately 3,000 pounds of coal, compose a trip. All loaded tripe carry steel drags on the last car, and automatic derails are located at advantageous points throughout the mine.All loaded trips are thoroughly sprinkled on the sectional partings and at the main parting. The track is sprinkled every idle day, or if needed, every day; from a large tank mounted on a truck hauled by a motor. Neither nozzle nor spray is used, as these were unsatisfactory. The water leaves the tank. through a 11/2-inch valve and is permitted to flow on the road through a horizontal 11/2-inch T. Water is obtained from filling stations located throughout the mine. It is stated by the officials that the use of this method of sprinkling permits the entire haulage roadbed to be wetted down in two hours."

Mar 1, 1930

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

The paper outlines the history and current status of the VALMIN Code and sets out the background, methodology, results and recommendations of the Independent Review of the VALMIN Code undertaken during 2001 under the Chairmanship of Ian Goddard. The paper is based on the final report of the Taskforce, which was submitted to the Board of The AusIMM for consideration.

Jan 1, 2002

By K Broadley

Risk and dispute resolution are linked. Dispute resolution techniques are brought to bear on a dispute - which is an outcome of a risk being wholly or partially realised. There has been an increasing awareness by business of risk as a component of doing business. There is an accompanying awareness of the need to manage risk - including legal risk. Many companies have undertaken a systematic review of their potential risks and endeavoured to put in place systems to help to avoid or manage risks. A legal risk management program will not prevent disputes arising. However, such a program should prescribe how that dispute will be managed. The management of the dispute will involve consideration of the dispute resolution procedure to be adopted. The most appropriate processes will take into account the practical, personal and commercial considerations surrounding the dispute and be as efficient, cost-effective and user friendly as achievable in the circumstances for the benefit of all the parties. Carrying on business in South East Asia, whether as an explorer or a mining operator, brings additional considerations to bear in legal risk management and the dispute resolution process. A significantly different perspective is required due to the varying nature of the legal systems in many South East Asian jurisdictions. These jurisdictions often have relative uncertainty as to the law. This impacts on the dispute resolution processes and also raises further timing and cost issues. The authors contend that this is all the more reason to endeavour, as practically as possible, to adopt a legal risk management and dispute resolution profile which will provide business with the greatest prospects of maintaining control of the dispute resolution process. This presents a greater chance of a successful outcome to the dispute. In these times of increasing pressures on profitability because of low mineral prices, all costs of a minerals business are being reviewed. In such times, a significant legal dispute may have even greater potential to adversely impact on the companies concerned, together with the careers of the people involved. In this paper possible approaches to managing disputes and a case study a legal dispute in which Freehill Hollingdale and Page were involved are discussed. The dispute concerned an international mining company developing a gold mine in Indonesia and one of its contractors in Indonesia. Described is how that dispute was resolved. This achieved a very satisfactory result for the client - all things considered. Given the æadditionalÆ problems associated with ascertainment and enforcement of ærightsÆ in South East Asia, the longer the parties can retain control over their dispute the better off they will be. For this reason, the authors set out in this paper the main additional dispute resolution tools available - that are appropriate for use throughout South East Asia.

Jan 1, 1999

By S. Sun

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest is reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi-component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By G. Halverson, K. Blower

"Giant Yellowknife Mines Limited (Giant) has been producing gold since 1948. Located at Yellowknife, Northwest Territories, Canada, see Figure 1, the mine processes approximately 1,200 short tons per day of 0.23 ounce gold per ton of ore.The majority of the gold in the ore is sub-microscopic and associated within the mineral arsenopyrite. This association complicates the extraction method since straight cyanidation will only recover 30% of the gold. The operations at Giant involve four essential steps, with an overall recovery of 87%. The steps shown in Figure 2 are crushing and grinding, flotation, roasting and cyanidation. These processes result in a number of effluent waste streams characterized in Table 1. These streams are combined and sent to a tailings storage pond for subsequent treatment prior to discharge to the environment.Giant is located just north of the 62nd parallel where winter temperatures drop to -40°C for extended periods. This entails storing effluent in dams over the seven month winter period for treatment during the relatively short summer season.The treatment method currently employed at Giant is an ""alkaline chlorination-arsenic precipitation-flocculation"" process. The pond water is subjected to three phases of treatment prior to being discharged to the environment as shown in Figure 3."

Jan 1, 1987

By Filipe Beretta

This study investigates geophysical logging capacity to predict coal quality. It was analyzed for possible correlation, some parameters determined via laboratory analysis of coal against results for the same parameter derived from wireline logs recorded by a geophysical probe. These probes detect variations in some rock physical properties, such as their natural gamma ray emissions and electrical resistivity. Results showed a strong correlation between natural gamma and ash content, establishing a linear model to estimate ash content from geophysical logging data with a low estimation error (less than 5%). Besides, results showed that there is no correlation between sulphur content or volatile matter and resistivity, neither with natural gamma of the rocks. Ash content derived from gamma ray values can be used as secondary information to evaluate coal quality during resources estimation, using methods such as soft indicator kriging. The methodology is illustrated using a case study at a coal deposit in south of Brazil.

Oct 1, 2009

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"FOREWORDFerrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade are in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory,and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the were discussed in the foreword of the first paper of this series, Report of Investigations 3606 Manganese Investigations. 1. Concentration of Manganese Ores,from the Drum Mountain District, Utah, by S. R. J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By J. Miettunen

"The lining of a grinding mill has an important role in creating the conditions for the grinding process. The main purpose of the lining is to transfer the energy taken by the mill motor to the contents of a mill. The power draw curve of the mill, if measured with sufficiently short intervals, describes how well the lining works in lifting and mixing the material to be ground.The power draw curve can also be used for determining the volumetric filling of a mill. This new measuring technique was developed at the Pyhasalmi concentrator in 1989-90. The measuring device with its PC-connections offers an excellent tool for controlling volumetric mill filling, for maximizing throughput and for research purpose (e.g. process studies, mill linings design).The paper describes the new method and the results achieved at Outokumpu's concentrators.INTRODUCTIONVarious methods have been developed for measuring mill load; weighing, noise, etc. Weighing is one of the most reliable methods but installing the sensor to existing mills is often difficult. Besides the load measurement does not indicate the volumetric filling if the specific gravity of the mill feed fluctuates. Noise measurement has often failed with its sensitivity to various disturbance sources.As known, the power draw measurement is one of the most accurate measurements in grinding circuits and therefore it has been utilized in sophisticated control, e.g. in power peak seeking algorithms for maintaining maximum grinding efficiency.About 10 years ago power oscillation measurement was developed at Pyhasalmi concentrator. In this method the amplitude of the oscillation caused by the lifters was measured. The oscillation amplitude and the mill filling has quite a good correlation and together with the power draw measurement it could be used for maximizing mill throughput (Koivistoinen and Miettunen, 1989). The main difficulties in this method were that the dependence between mill filling and the amplitude is unlinear and that the dependence also is individual for each mill.The method developed during 1989-90 is also based on the power oscillation but on its phase shift. In principle level of the material in a mill is measured. The method has been successfully used for maximizing throughput at Pyhasalmi and Enonkoski concentrators and at Harjavalta slag concentrator."

Jan 1, 1991

By Trevor Yeomans

"NVI Mining’s Myra Falls Operation is a forty year old underground mining operation feeding a 4000 mtpd concentrator.The current Mill, built in 1985, was designed to process a large massive sulphide ore-body. This ore-body, known as the “HW”, contains about 50% pyrite. Value minerals are chalcopyrite, and sphalerite, with precious metals occurring in all mineral types.By 1997, mining of a new ore-body, known as “Battle-Gap” commenced. Mineralogically complex, the new orebody contains about 15% pyrite, copper minerals including primary chalcopyrite, secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite.Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected.Following significant metallurgical testwork, a new fully sequential copper-lead-zinc flotation flowsheet and reagent scheme was developed.This sequential flowsheet was progressively installed and commissioned during 2006.Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, whilst increasing copper recovery by 10%.INTRODUCTIONNVI Mining operates the Myra Falls Operation near Campbell River on Vancouver Island, BC. The complex has been in operation since 1966 with mining being predominantly underground. One unique feature of Myra Falls is that the mine operates within a BC Provincial Park.In 1985, a new large massive sulphide ore-body (HW) had been defined, and metallurgically tested. A new concentrator was built based upon this massive pyrite, chalcopyrite, and sphalerite mineralization producing copper and zinc concentrates by conventional flotation methods."

Jan 1, 2008

By R M. Briggs

Kapowai Caldera Complex (KCC), located 10 km west of Tairua (eastern Coromandel Peninsula), is a late Miocene composite collapse caldera, formed during eruption of several small and large volume andesitic rhyolitic ignimbrites. Numerous epithermal Au-Ag mineral deposits and associated alteration zones at the KCC are related to caldera (rhyolite lava domes, intracaldera faults) or regional structures (faults). The main epithermal deposit exposed in the central KCC is associated with an E-W striking structural boundary fault that cuts the Welcome Jack rhyolite dome. Propylitic (calcite - chlorite) and sericitic (quartz - sericite) alteration haloes surround this deposit. Sporadic zones of sericitic alteration are also exposed within and on the margins of the Bulls Run rhyolite dome complex. Epithermal systems post-dated emplacement of these rhyolite domes, but were controlled by them. Propylitic alteration of ignimbrite in the floor of the Kapowai and Kauaeranga valleys is related to the major NE-trending Kapowai Fault which extends SW to south of Thames. Alteration along this fault pre-dates alteration associated with the rhyolite lava domes. Numerous sericitic and propylitic altered welded ignimbrite, rhyolite and andesite lava lithic fragments have been sampled from intracaldera ignimbrites, and although no direct source is known, they infer the presence of buried epithermal systems. Repeated epithermal activity at the KCC is inferred by the exposed epithermal deposits/alteration zones and the older buried geothermal systems. Silicic caldera volcanoes are considered to be critical volcanic environments for epithermal Au-Ag mineralisation in Coromandel, but are highly variable and need detailed stratigraphic, structural, petrologic, and geophysical studies to characterise them.

Jan 1, 1999

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. When enough circulars have boon completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed b., bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual nines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); Ventilation; wage, contract and bonus systems, etc.

Jan 1, 1931

By J. P. Powell

The application of secondary producing methods for recovering additional oil from known fields has been recognized for many years as important to the economy of the nation. One of the most successful secondary methods is waterflooding, which conserves our natural resources by preventing premature abandoment of stripper leases and revitalizing previously abandoned areas. Waterflooding as a secondary-recovery method was introduced into the Midcontinent region in 1931, and its use as such has become widespread. As with most new methods, the most favorable fields and leases received primary attention, whereas those with viscous oil or less favorable sand characteristics were bypassed. Numerous reports3 4 5 6/ have been published giving the results of individual waterflooding projects, In this report, attention is directed to the effect of a single factor, the viscosity of the oil produced,

Jan 1, 1959

By Steve Dillingham

Here in the United States, as well as around the world, pose a daily dilemma - to wash or not to wash. Let’s face it, all trucks, especially our industry work horses - bulk trucks - get dirty. We all know that these units can be very expensive and washing them keeps your business investment looking new, improves public relations, fuels company pride, and facilitates equipment safety and preventative maintenance inspections.

Jan 1, 2001

By Manqiu Xu

"Ore grades are decreasing and ore deposits are becoming more complex. In order to make a sound economical decision about a mining project, metallurgical testwork must be carried out. A few large “representative” samples cannot represent the metallurgy of a large ore body and a large number of samples reflecting variation in ore head grades and in mineralization types must be obtained for proper metallurgical studies, including flowsheet development for a greenfield project. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to establish a correlation between values recoverable and values contained in the ore body that can include multiple pay metals. With this information, a sound economical decision can be made about the viability of a large mining development project.INTRODUCTIONThe demand for minerals today is historically high as many countries are being rapidly industrialized. The supply for these minerals is not necessarily running short. However, it is widely accepted that the world today is running short of the easy to mine and easy to process ore deposits. As ore grade is decreasing and ore mineralogy is becoming more complex, metallurgical testing must be fully conducted in order to make a sound economical decision about a mining project. For a high-grade and high-quality deposit, it is hard not to make a good profit even with low metal prices. For a low-grade and hard to process deposit, the profit margin is much lower and is dependent on the throughput and the recovery of valuable minerals. The recovery of valuable minerals is a function of ore grade and mineralogy and it must be experimentally determined for a given processing option.At Vale Base Metals Technology Development, metallurgical testing for an existing operation or brownfield project is termed as Ore Evaluation, while metallurgical testing for a greenfield project is termed as Flowsheet Development (Xu, 2011). In the past, metallurgical testing involved a few large composite samples for lab and pilot plant testwork. As ore deposit becomes less homogeneous and more variable, a few large composite samples cannot represent the metallurgy of a large ore body. In addition, useful information about the deposit such as zones of “impurities” or floatable rock minerals would not be obtained. Different processing strategies could have been developed if the locations and sizes of these zones were known in advance. For proper metallurgical studies, a large number of samples reflecting variation in ore head grades and in ore mineralization types must be used. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to estimate values recoverable in the ore body that can include multiple pay metals. Ultimately, the recovery verses ore grade relationship will be used in business decision-making."

Jan 1, 2013

By H. Kenworthy

"INTRODUCTION ..Although the occurrence of iron ore in Missouri was recognized by Marquette as early as 1673, the first known mining and smelting operation was conducted in 1815. This operation was near Arcadia, Iron County, the first of its kind west of the Mississippi-Ohio River system. Several small furnaces of short life were erected in Missouri in the ensuing 30 years. However, until the extensive deposits of Iron Mountain and Pilot Knob were opened between 1843 and 1850, the state remained a minor producer of iron. It was this district which was chiefly responsible for the prominent position Missouri held in the iron industry until the late 1880's. At this time the easily minable high-grade ores became exhausted and the discovery of the immense Lake Superior deposits depressed the raw-ore price to such an extent that any mines ceased to operate. 3/Small yearly production of iron ores continued in Missouri to the present. Owing to war demands for hard ore suitable for open-hearth steel, the M. A. Hanna Co., through its subsidiary, the Ozark Ore Co., reopened the Iron Mountain, deposits and installed new equipment in an old concentrator to handle the low-grade ores left from previous operations. At present, ore production is from open pits, but underground mining is contemplated in the future. About 2,000 tons a day of iron ore is treated by gravity concentration of material from the open pits in the immediate vicinity. The concentrate is shipped to the Birmingham, Ala., district and to Granite City, Ill., for smelting. The coarse tailing is sold for ballast and concrete aggregate. The iron requirements of the concentrate stipulated by the purchaser are not difficult to meet, but the phosphorus is frequently higher than desired. For 1946 the concentrates averaged 54.18 percent iron and 0.235 percent phosphorus with low sulfur. The Ozark Ore Co. concentrate, however, sometimes contains as much as 0.40 percent phosphorus. The phosphorus in ores from those portions of the deposits wherein the phosphorus occurs with siliceous gangue is readily rejected in the milling, but in much of the ore the phosphorus is associated with the iron and concentrated with the iron minerals. Selective mining is impossible owing to the spotty occurrence of the phosphorus mineral. Often within 5 feet the ore will change from low phosphorus to high phosphorus, and it would be expedient to find a method of rejecting enough phosphorus at the mill from the latter type of ore to meet the phosphorus specification."

Feb 1, 1948

By Amir Zavichi

Today, with the necessity of timely, on-budget and high quality completion of projects, proper use of construction equipment is essential to ensure project success. Construction equipment places a large monetary burden on the project and if not utilized efficiently, it can result in economic losses. Cranes are one of the most important and expensive operational devices on construction sites. They play a central role, and often activities that rely on crane services fall on the project?s critical path. Currently, material-handling scheduling is done by the crane operator or by an on-duty superintendent using his/hers personal judgment, making the process manual and timeconsuming. Thus, developing an optimal schedule, which considers different dynamic constraints in construction job site, may not be possible based on the current practice. This leads to longer operation times and a negative impact on project cost. This paper presents the latest results of an ongoing study, which aims to design and implement a nearreal time crane operation decision support system to be utilized directly by the crane operator or as an aid for the superintendent in scheduling optimal operation services. This system has several advantages such as maximizing the efficiency of crane operations, guaranteeing the best operation possible to reduce the crane?s travel time, reducing crews and equipment idle time, and minimizing the dependence on subjective human judgments.

Aug 1, 2013

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004