Search Documents

By Yasuo Ojima

A new copper continuous converting process was investigated to evaluate the possibility of its application in the commercial operation. The tests were performed both in the laboratory and in pilot plant scale. Bath smelting process with the use of the top submerged lance technology was applied in these tests. Furnace shape was modified to a lengthwise eylindrical one with a settling area. The furnace monitor was put in the settling area to check the furnace from inside, FeOx-Si02, FeOx-CaO and FeOx-CaO-Si02 based slag systems were used to check their efficiency, The optimum slag chemistry to have good metallurgical results was discussed and FeOx-CaO system with some Si02 content turned out to be preferable although it has not been practically used, In this pilot plant test feeding rate of I tIH of solid grain matte was charged consecutively for two weeks and continuous converting could be done successively. This process is expected to overcome the problems of existing processes and be easily applied in existing plants.

Jan 1, 2003

By Lv Guozhi, Ren Xiaodong, Liu Yan, Dou Zhihe

"This paper investigated a new desulfurizer, dolomite and ferrosilicon. Magnesium vapor produced by silicothermic reduction of dolomite and ferrosilicon in an immersion tube of molten iron was injected into the molten iron by carrier gas through the underpunch of the tube and desulfurization reaction occurred. In order to explore the desulfurization process of molten iron by the new desulfurizer, the thermodynamics, and experiments of magnesium vapor production and desulfurization have been studied. Through thermodynamic calculation, the reaction temperature of magnesium vapor production by 75ferrosilicon and light-burned dolomite is 1838K in the standard state and decreased with the decreasing partial pressure of magnesium vapor, PMg· When PMg=25kPa, the reaction happens at 1673K. From experiments of magnesium vapor production, reduction efficiency of Mg vapor is about 60 % in 15 minutes at 1673K. From hot metal experiments, the desulfurization efficiency is 89.35%, and the lowest sulfur concentration after desulfurization is 46ppm.IntroductionPretreatment desulfurization of hot metal has become a necessary step in modem optimizing steelmaking process for its cheap cost, which can not only liberate of blast furnace productivity and reduce the burden of produce steel, but also effectively improve overall economic efficiency of the iron and steel system[l-ZJ_ At present, injection magnesium particle is one of the two main methods of desulphurization in hot metal owing to its strong affinity for sulphur, low amount of slag produced, low iron loss in slag skimming and low equipment investment[3l. However, there are still some insufficiencies on the hot iron pretreatment with magnesium particles at present[4-5l"

Jan 1, 2013

By Yasushi Sawada

An experimental investigation was carried out to study the rates of reduction of iron oxides dissolved in liquid Ca0-SO2-A203 slags by Fe-C droplets at temperatures ranging from 1325 OC to 1550 OC. The %FeO in the slag was varied from 5.5 to 18. Flash X-ray images were employed to observe the behavior of Fe-C droplets in the slags during the reactions and for determining the slag-gas-metal interfacial area. Effect of P205 in the slag and sulfur in the droplet was also investigated. The reduction rates were determined by measuring the volume of CO evolved as a function of time and the estimated slag-gas- metal interfacial area. The reduction rates have increased with increasing %FeO in the slag and the slag temperature. The experimentally established relationship between the reduction rates and FeO (wt%) in slag is given by

Jan 1, 1992

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By Jordan Mayorga, Joseph Kopp, Robert Boehm, Daniel P. Cook

"Solar generated power has long been considered a useful energy source only for low-energy density and non-mission critical use, such as providing electricity for residential applications. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar- 1 near Las Vegas, have demonstrated that solar does have application to high energy density industries such as materials and chemical production. This paper will discuss the current operating con_guration of the Solar-1 facility and show how proposed modi_cations, such as addition of thermal storage and use of liquid salts as the working uid, can further improve the e_ciency and energy production of the plant.IntroductionThe United States as a nation is the largest consumer of energy in the world at an estimated 29 trillion kWh per year[1], which is roughly 15% of total global energy consumption[2]. On a per capita basis, the United States also leads most of the world, using an average of 96,000 kWh per person[3]. Roughly 40% of the energy consumed in the United States was produced from petroleum, 23% from coal, 23% from natural gas, 9% from nuclear and the remaining 5% from renewable sources such as solar, geothermal, wind, and hydroelectric[1].Energy demands associated with the industrial-scale production of chemicals and materials is a signicant portion of the United States total energy consumption. Roughly 33% of the energy consumed in the United States is used by the industrial sector, with 22% of this amount used in chemical production, 16% used in petroleum rening, and 14% used in the smelting and rening of metals[1]. Energy costs are also a signicant, if not the most signicant, portion of the total production costs for many materials. For example, roughly 30% of the cost of producing aluminum is the electricity used in the Hall-Heroult process [4], while the cost of energy is roughly 15% of the total cost of producing steel products [5].The primary sources of power for the industrial sector have been coal, petroleum, hydro- electric and nuclear. The use of alternative energy sources, e.g. solar, wind, geothermal, for industrial materials production has been slow in coming because they are intermittent and low-energy density sources, i.e. no solar power at night, no wind power when the air is still, etc. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar-1 (NS-1) near Las Vegas, have demonstrated that solar can have application to high energy density industries such as materials and chemical production.This paper will discuss the current conguration of the NS-1 facility, and potential modications to the facility that will increase both its power e_ciency and power density."

Jan 1, 2010

By S. Stoyanov, M. Cross

"Silicon components containing transistor circuitry are at the heart of electronic products such as computers, mobile phones, etc. These components are connected to printed circuit boards (PCB's) using solder material that acts as the conductor for both electricity and heat. During the lifetime of a product it will undergo many thermal cycles where the chip becomes hot during product operation and then cools when the product is switched off. At the product design stage engineers undertake thermo-mechanical simulations to predict the thermal stress in the solder joints due to this thermal cycle and to ensure that the stress magnitude will not result in early fatigue-type failure. The design engineer's aim is to identify component parameters which ensure that the solder will survive beyond a certain number of thermal cycles.The aim of integrating computational mechanics and optimization tools together is to speed up dramatically the design process. From viewpoint of a design engineer in the electronics manufacturing sector, these tools can be used to quickly estimate key design parameters (i.e. material properties, product dimensions, etc) that will guarantee the required product performance. In this paper a modeling approach coupling computational mechanics techniques with numerical optimization is presented and demonstrated. The integrated modeling framework is obtained by coupling the multi-physics framework - PHYSICA - with the design optimisation tool- VisuaLDOC. Thermo-mechanical simulations are presented that predict the creep strains in solder material. Different numerical optimization procedures: Direct and Response Surface based optimization plus Design of Experiments, are tested as a part of this modeling framework."

Jan 1, 2001

By Glenn C. Miller

Cyanide is the most common lixiviant for extraction of precious metals, and its efficient use in open pit mines has contributed to the increase in world production of gold during the previous two decades. With this expansion of precious metals mining using cyanide, public concerns have developed in response to the inherent public perception of cyanide as a tox-in as well as a series of environmental problems that are directly or indirectly related to cyanide use in open pit mining. Some of these have technical or regulatory solutions, while others will require additional investigation before they can be resolved. The following discussion will summarize some of the public concerns regarding the use of cyanide in precious metals mining. The issue of cyanide use in large scale precious mining is controversial, and recent banning of cyanide use in open pit mines in Montana, or complete banning of cyanide in Hungary has reflected those international concerns. The underlying basis for some of the bans (e.g. Montana) reflect a general concern of the environmental impacts of mining, rather than specific issues related to risk of cyanide use. The human safety record for cyanide use, particularly in the developed countries is good, and cyanide is clearly the most efficient lixiviant for precious metals. Indeed, the relatively short lifetime for cyanide in the environment renders it one of the less problematic chemicals used for extraction of gold from ore. Mercury amalgamation or use of bromide as a lixiviant are certainly much more problematic. What, then, is the basis f~r the international concern about precious metals mines that use cyanide. Ifuse of cyanide for gold recovery is to continue, what additional infom1ation needs to be developed that will allow a better management of the risks of cyanide? Which of the concerns are directly related to cyanide, and which are indirect concerns that more related to effects of open pit mining. Under what conditions should use of cyanide be discouraged? DUl::ing June of 2000 the United Nations Environmental Program conducted a two-day workshop on cyanide use in mining that was attended by persons from the mining industry, regulators and environmental community. Support and attendance at this workshop reflected concerns by all three groups on further restrictions for cyanide use and the emerging potential for guidelines for better management of the catastrophic release of cyanide-containing mining waste. The following discussion is meant to focus-on those risks and explore the basis for an often negative reaction to precious metals mining using cyanide. It is presented in the format of a statement, followed by a discussion. While admittedly provocative, the statements are meant to express the concerns? of the public regarding cyanide and the mining industry.

Jan 1, 1998

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By Run-sheng xu, Hai-yang WANG, Di ZHAO, Teng-fei SONG, Jian-Liang Zhang

This paper was mainly focused on the different semi-cokes and charcoal which could be new fuels for blast furnace injection. Through the comparative study with bituminous coal and anthracite coal, the properties of semi-cokes and charcoal were presented in this research. 10 indexes of different fuels were obtained by different standard experiment, including proximate analysis, ultimate analysis, igniting point, explosivity, transportation characteristic, ash properties, grindability, calorific value, combustibility and reactivity with CO2. According to the data analysis, it provided a theoretical basis for rational utilization of various blast furnace fuels, and helped to broaden the scope of the blast furnace injection fuels. This research could contribute to energy conservation, emissions reduction, and sustainable development of iron and steel enterprises.

Jan 1, 2015

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By George Owusu

A study has been carried out on the use of solvent extraction, instead of the traditional zinc dust cementation process, to remove copper from concentrated zinc sulphate leach solutions. In a series of experiments using plant solution containing 1.9 g/L Cu, 2 g/L Fe, 173 g/L Zn, 7.9 g/L H,SO,, 0.25 g/L Cd, 15 mg/L Co etc. and LIX 622 in SX-1, up to about 97-98 % of copper present in the zinc sulphate leach solution was extracted with negligible co-extractions of zinc, iron, cadmium, cobalt, etc. pH modification was not required for this reagent. The copper loaded organic was almost completely stripped using 150 g/L sulphuric acid. Investigations into the effect of any possible organiclextractant contamination on zinc electrowinning showed (if any) little effect on current efficiency if the organic contamination is less than 45 ppm; current efficiencies of 95-97 % were obtained. At organic contaminations higher than 45 ppm, the current efficiency dropped to about 92- 94 %. Visually, the organic-contaminated cathode sheets had rough surface morphology, becoming more intense with increasing organic concentration, compared to the non-contaminated cathode sheets.

Jan 1, 1998

By Yavuz Ali Topkaya, Aydin Rusen

"In this study, zinc and lead recovery from zinc plant leach residue obtained from Çinkur using hydrometallurgical methods have been investigated by laboratory scale experiments. Considering more than one million tons leach residue (LR) rich in Zn (12.43%) and Pb (15.51%) in the stockyard and environmentally hazardous, it is essentially necessary to process Çinkur LR. Zinc and lead have been recovered in two main stages. As a first step, Çinkur LR was releached by using hot sulphuric acid for zinc recovery. About 72 % Zn was recovered by using 150 g/l H2SO4 at 95 oC in 2 hours with a pulp density of 200 g/l. Secondly, for lead recovery brine (NaCl) leaching tests were performed on the secondary Çinkur LR obtained after acid leaching process. In brine leaching while lead recoveries up to 95 % could be attained at a low pulp density, the maximum recovery obtained was 84.9 % at a high pulp density (200 g/l) with 300 g/l NaCl concentration in 10 minutes at 95 oC. Introduction Zinc and lead have been known and used by humans since ancient times and also they are important nonferrous metals [1]. Zinc and lead have different properties thus they are used in various application areas, ranging from automobiles to construction, from batteries to textile. Zinc and lead deposits are widely distributed in the Earth’s crust. The principal ore mineral for zinc is zinc sulfide, Sphalerite (ZnS), and lead sulphide, Galena (PbS), is the main source of lead in the world [2].Although zinc is generally produced from sulphidic ores (ZnS) or concentrates by Roast – Leach – Electrowinning (RLE) in the world, in Turkey, zinc production is based on zinc carbonate ores (ZnCO3), and at the Çinkur plant zinc was produced from zinc carbonate from its establishment to 1997 due to high reserves of zinc carbonate in that region. Çinkur is the only plant in Turkey that produces Zn from primary ore containing ZnCO3 by Waelz – Leach - Electrowinning route [3]. However, due to depletion of local high grade ores, oxidized ore concentrates were imported from Iran after 1997, until this plant was shut down. Therefore, there are two different leach residues (LR) which are Turkish LR (TLR) and Iranian LR (ILR) in Çinkur stockpiles. It has been estimated that the total amount of leach residue is more than one million tons of which the major part is Turkish leach residue (TLR)."

Jan 1, 2008

By Batric Pesic

Dissolution of gold with elemental bromine was studied by using a rotating disc technique. The main parameters studied were: bromine concentration, stirring speed, pH, and temperature. Additionally, effect of copper, iron, and manganese was also examined. A special attention was paid to elucidate the role of cations, primarily Na+, during gold dissolution. It was found that gold dissolution with bromine was characterized with two pH regions. Below pH=7, gold dissolution was independent of pH, and above this value, gold dissolution decreased with pH increase. Gold dissolution rates were proportional with concentration of bromine. Two regions, diffusional and kinetic, were observed with respect to stirring speed. with respect to the role of Na+, and cations in general, they play absolutely no role during gold dissolution with bromine, unless they are in their lower oxidation state and become oxidized by bromine. In that case they have a negative effect because of bromine consumption.

Jan 1, 1991

By Jian-hua Ren, Guang-liang Wu

A lot of dust is produced in iron and steel enterprises, giving rise to serious environment pollution, with which all countries are trying to find methods to deal. The influence of relevant technological factors on dephosphorization was investigated in laboratory, and the effect laws of that were analyzed. The results demonstrate that, in the given conditions of the best slag-metal proportion for hot metal dephosphorization is 1:10, and the optimum temperature is 1350 , The phosphorus distribution ratio of dephosphorization agent containing converter dust of 30% has the maximal value, with dephosphorization rate reaching 85%. Under the optimal conditions, premelting dephosphorization agent can significantly improve the ability of dephosphorization, dephosphorization efficiency increasing to 92%. Therefore, the dust can substitute the oxidant and fixative of dephosphorization agent, be used in hot metal dephosphorization, to enhance the efficiency of utilization.

Jan 1, 2016

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By S. J. Macnaughton

The Olympic Dam deposit in South Australia contains 2% copper and 0.06% uranium, which are present as bomite, chalcocite, chalcopyrite, uraninite, coffinite and brannerite. The copper is principally recovered using flotation. The flotation tailings, which contain the bulk of the uranium, and typically 0.3% copper, are leached using sulfuric acid and an oxidant at atmospheric pressure. This paper describes the results from a detailed investigation of the leaching behaviour of this ore. The influence of acid strength, Fe3+ concentration, redox potential and temperature on the dissolution of uranium and copper minerals was studied. Experimental data were obtained from extensive batch leach tests. Mineralogical studies, including SEM analysis of individual mineral grains, were also carried out. The maximum extraction of uranium determined experimentally was in good agreement with that predicted from SEM determination of the proportion of refractory brannerite in the ore. The leaching rate of copper was found to be independent of acidity over the range 20 g L-&apos; to pH 2.0, but was strongly dependent on temperature and Fe3+ concentration. Uranium extraction showed a weak de endence on acidity, Arrhenius temperature dependence and a complex co-dependence on F>+ concentration and redox potential. A kinetic model has been developed, which predicts copper and uranium dissolution. This model will be incorporated into a more comprehensive model that can be used to predict leach performance and reagent consumption for specific ore samples.

Jan 1, 1999

By R. M. Cunningham

Asarco operates one of the largest individual copper electrolytic refineries in the world at Amarillo, Texas. The feed for this refinery is a mixture of anodes produced at Asarco smelters and copper purchased t?om a number of primary and secondary sources. The variation in feed makes it imperative that the refinery practices state-of-the-art quality control to minimize the effects&apos;of unwanted impurities in the electrolytic refining process. In late 1993, a plant designed to sigru6cantly reduce the antimony and bismuth levels in the electrolyte was commissioned. The purification plant uses ion exchange technology in conjunction with a novel strippiing system developed by Zeneca Specialties (U.K.). The strippiing system permits the recycling of the eluant and thus avoids the extremely high costs of stripping with conventional reagents. In addition, the environmental impact of treating the eluant for recovery of antimony and bismuth is minimized. This paper outlines the development of the technology and, in particular, describes the operational practices and improvements at Amarillo since the commissioning of the plant.

Jan 1, 1997

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By J. Hamisch

Climate policy regarding perfluorocarbons (PFCs) may have a significant influence on investment decisions in the production of primary aluminum. This work demonstrates an integrated analysis of the effectiveness and likely economic consequences of different climate policy options. In our study we first compare atmospheric observations to the available estimates of PFC emissions for the baseline years 1990 and 1995. We then present projections for regional emissions of PFCs from the aluminum industry using the MIT Emissions Projection and Policy Analysis model under different policy scenarios. Abatement costs for emissions of PFCs and C02 are compared in the context of the Kyoto Protocol.

Jan 1, 1999