Search Documents

By Enrico Cerilli, Bryan Salt

Xstrata Nickel’s Sudbury Smelter has systematically developed its converting aisle from a single stage to a counter current multi stage converting process. This has required the development of two unique converters; the Slag Cleaning Vessel (SCV) and the Slag Make Converter (SMC). This has resulted in a unique three stage converting process that enables treatment of secondary materials and producing a slag that can be discharged without further treatment. The paper will also discuss future changes currently being considered to further improve environmental, plant hygiene and productivity performance.

Jan 1, 2009

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By Dean David

The evaluation of a new mineral sands prospect with unusual characteristics is described, The heavy minerals are very fine grained, have comparatively low average specific gravity (3.6) and are altered. Poor performance by conventional processing techniques made it necessary to trace the response of the major minerals during the separation processes, QEM*SEM® was used to quantify mineral volumetric abundances and mineral locking in magnetic and gravity separation products.

Jan 1, 1989

By M. S. Moats

A considerable amount of research has been conducted to determine the causes of anode passivation. Chemical and electrochemical reactions that occur after passivation have received little attention. Chronopotentiometry, linear sweep voltammetry, cyclic voltammetry, and impedance spectroscopy have been used to elucidate three reactions that occur after passivation of commercial copper anodes. These involve the dissolution of silver and subsequent cementation and transformation of selenides, the oxidation of lead sulfate to lead oxide, and oxygen evolution. The amount of silver dissolution depends on the silver content of the anode, the time to passivation, and the molar ratio of Ag/(Se+Te). The oxidation of lead from PbSO4 to PbOx explains a potential plateau of oxygen evolution. Silver affects the duration of oxygen evolution on the PbOx. Anodes containing kupferglimmer display a characteristic oxygen evolution potential. It is believed that kupferglimmer provides a lower overpotential for oxygen evolution than the other slime phases or passivated surface.

Jan 1, 1999

By T. T. Natarajan, Nagy EI-Kaddah

"Numerical simulation of electromagnetic confinement systems generally requires large CPU time due to the strong coupling between the electromagnetic and the free boundary problems. The present paper examines the accuracy and the computational efficiency of the most common numerical schemes used in modeling such systems. Levitation melting was taken as a test case. In this study, a comparison was made between the finite element and surface integral methods for electromagnetic field calculations. The computational efficiency of Lagrange and the modified Hestenes methods for solving the free boundary problem were investigated. The convergence of the Lagrange method was found to be much faster than the modified Hestenes method. It was also found that finite element method not only gives accurate solutions, but faster convergence to the final equilibrium shape than the surface integral method. The applications and the limitations of these techniques in modeling electromagnetic confinement systems will be discussed.IntroductionIn recent years there has been a growing interest in the use of electromagnetic forces for confinement of molten metals as a means to eliminate molten metal contamination during melting and to improve surface quality of cast products. Continuous casting of metal without contact of a mold is now a reality, and is being commercially applied for casting of aluminum slabs /1/, and copper rods /2/. New applications of electromagnetic confinement in melting and casting include containerless melting (Magnetic Suspension Melting) /3/, edge containment in twin roll casting, and meniscus shape control in continuous casting of steel /4/.Modeling of confinement systems involves the determination of the electromagnetic field and the equilibrium shape. These two problems are strongly coupled due to the dependence of the field on the shape of the melt. While significant advances have been made in computational electromagnetics /5/, the application of developed computational techniques to electromagnetic confinement problems is not a simple task. The principal difficulty in using these methods is that the solution domain is not known a priori. due to coupling between the electromagnetic field and the free boundary problems. These two problems have to be solved simultaneously, leading to an iterative solution procedure. As a result, numerical simulation of electromagnetic confinement systems are computationally intensive with computational time at least an order of magnitude larger than the fixed domain problems."

Jan 1, 1994

By Petre Stelian Nita

In small steelmaking shops, in foundries and forging plants, there are not too many option to recycle the basic slags, which are not suitable for many purposes of recycling, because of their low chemical and structural stability. A solution of an adequate recycling is a direct recycling in EAF. Several quality requirements, physico-chemical properties and proportions of slags must be analysed. The progress in this fields permites to establish an adequate proportion of recycled slag, based on enough exact computation of the related property. For oxydizing slag, obtained during melting and in the first part of decarburization operation, the problem of phosphoms contents can be analysed using the phosphate capacity (C PO34-). For reducing periods, during deoxidization operation, desulphurization also occurs and the problem of the sulphur contents can be analysed using the sulphur and sulphide capacities ( Cs / Cs) Between this two complex thermodynamic indicators of the slags. a direct relation is established, using thermodynamic aspects, resulting from the equilibrium constants for dephosphorization and desulphurization process and also, using the optical basicity of slags, computable from the chemical analysis of the slags. On this basis starting from the steel quality requirements. adequate strategies can be established in order to obtain high rates of recycling (between 50-80%) of steelmaking slags. Important cost savings are obtained through this procedure, based on the correct amounts of the fresh lime, iron ore and fluidizers. Keywords: Slag, Properties, Recycling

Jan 1, 2003

By C. T. Yavuz

Higher environmental standards have made the removal of arsenic from water an important problem for environmental engineering. Iron oxide is a particularly interesting sorbent to consider for this application. Its magnetic properties allow relatively routine dispersal and recovery of the adsorbent into and from groundwater or industrial processing facilities; in addition, iron oxide has strong and specific interactions with both As(III) and As(V). Finally, this material can be produced with nanoscale dimensions which enhance both its capacity and removal. The objective of this study was to evaluate the potential arsenic adsorption by nanoscale iron oxides, specifically magnetite (Fe3O4) nanoparticles. We focused on the effect of magnetite particle size on the adsorption and desorption behavior of As(III) and As(V). The results show that the nanoparticle size has a dramatic effect on the adsorption and desorption of arsenic. As particle size is decreased from 300 nm to 12 nm the adsorption capacities for both As(III) and As(V) increase nearly 1000 times. Interestingly, this increase is more than expected from simple considerations of surface area and suggest that nanoscale iron oxide materials sorb arsenic through different means than bulk systems. The desorption process however, exhibits some hysteresis with the effect becoming more pronounced with small nanoparticles. This hysteresis most likely results from a higher arsenic affinity for magnetite nanoparticles. This work suggests that magnetite nanocrystals and magnetic separations offer a promising method for arsenic removal.

Jan 1, 2006

By B. Ozturk, K. Ito, R. J. Fruehan

"A simulation model for bath smelting processes for the production of iron was developed which predicts the coal, flux, ore, and oxygen consumptions and the off gas volume, temperature and composition. The model is comprehensive in that it takes into account all of the important variables including coal composition, metal composition, ore composition, slag basicity, post combustion ratio, (PCR), prereduction degree (PRO), heat transfer coefficient (HTC) , flux, scrap charge, and heat losses. Four basic cases were considered: I. 30% PRO-50% PCR; II. 90% PRO-O% PCR; III. 60% PRO-30% PCR; and IV. 0% PRO-50% PCR. Several different coals were considered and a sensitivity analysis of the critical variables was performed. The model also estimates the sulfur content of the metal. The major conclusions included:1. Post combustion significantly reduces coal consumption but above 20% PCR little reduction of FeO to Fe can be performed with the off gas.2. Prereducing to FeO (Case I) and having as much post combustion as consistent with good heat transfer is an attractive process. This process only requires a simple pre reducer, uses less coal, and is relatively insensitive to the type of coal used.3. High off gas temperatures may pose a potential problem. The off gas temperature can be reduced by using an 02-Air mixture for post combustion, limiting post combustion or adding water to the gas.4. The use of CaC03 in place of CaO or of supplemental electricity does not appear attractive.5. The melting unit is theoretically an energy efficient scrap melter. For Case I using 200 kg of scrap as part of the charge the coal consumption decreases by about 80 kg.6. With PCR > 30% the FeO content of the slag is expected to be 2-5%, and the metal will not be saturated with carbon. These factors and the increased sulfur load since coal is the fuel indicate the sulfur content of the metal may exceed 0.25%"

Jan 1, 1988

By L. B. Tsymbulov

Sulphide melts formed in the course of smelting of nickel and copper-nickel feed (matte) actually are sulphide-metallic melts since sulphur contained in the melts is in deficiency with respect to metals. The level of metallization is rather relevant feature of sulphide melts and is widely used in calculating material and heat balances for pyrometallurgical processes. Despite of the above parameter? importance, the investigators have no single opinion on what should be understood under metallization level and the method of its determination. In the present study we present the results of our own experimental and theoretical researches that have allowed determination of some mechanisms of sulphide melts? crystallization. Based on the mechanisms revealed new scientifically justified approach has been offered for determining level of metallization of the components present in sulphide melts. It has been demonstrated that sulphur distribution between the melts is substantially different from generally accepted concept.

Jan 1, 2006

By M. Patel, A. W. Piper, R. A. Forsdick

"Lead bullion is refined in kettles to remove the contained impurities such as copper, antimony, silver and bismuth. These impurities are removed sequentially by the addition of one, or more, reagents to the bath. Impurity elements react selectively with the reagents to form a dross layer on the surface that is subsequently removed for further processing. Mixing the lead bath using specific impeller designs, which form a vortex to ensure that good contact takes place, carries out the reactions. It is important that the mixing is controlled to achieve the optimum bath conditions and hence good dross grades.This paper presents initial modelling work on the kettle refining process using both physical modelling (Water Models) and mathematical modelling (Computational Fluid Dynamics - CFD). Comparisons between measured plant data and simulation results are given.IntroductionThe refining of lead bullion takes place in hemispherical kettles of varying sizes. It is normal practice to remove the impurity elements sequentially, by the addition of reagents, which selectively react with the impurity element. The impurity element forms a dross layer on the surface, which can be removed for subsequent processing at the end of the reaction period.All the refining stages in the production of lead and lead alloys involve mixing the lead bath, although different conditions are required for each stage. At Britannia Refined Metals mixing is achieved using either 3 or 4 angled or flat blade impellers, which generate a vortex in the central region of the kettle. However, throughout the industry a wide range of mixer types are used which are all trying to achieve the same result."

Jan 1, 1999

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By Marcela Morvová, Mário Janda, Morva Imrich

"The possibilities of greenhouse gas mitigation using various methods are brought out. The special case of utilization of mixture of CO2 with other greenhouse gases in a synergetic way inside non-thermal plasma based system is described in detail.Measurements on pilot system comprising pyrolysis chamber as alternative energy system (production of hydrogen and liquid tar) were made for various biomass and waste as the input material. The exhaust from this system was treated with non-thermal plasma gap suitable for up to 650Nm3/hour of exhaust gas flow. Condensable portion of exhaust is liquefied in distillation unit; produced hydrogen is stored on-line inside nano sized carbon of our own production.The CO2 removal efficiency varies depending on exhaust composition between 45 to 98%. Other oxides as CO, NOx, SOx and several hydrocarbons and VOC are also removed. The main product connected with CO2 removal is a solid powder of proteinoid nature. There exist strong probability, that precursor of the origin of life on the Earth from primary atmosphere were formed in the similar way as it is present in the electric discharge system used. Our system is equipped with on-line as well as ex-post analysis of all forms of products. We have also developed a system for recuperation of all forms of produced heat. It is stored inside as latent heat of waxes.IntroductionNatural greenhouse effect on the Earth is caused mainly by water vapour with the average absolute concentration about 4%. Other gases able to absorb long-wave radiation and thus this causing greenhouse effect are CO2, CH4, N2O, halocarbons and as precursors ozone and NOX. Some of them we produce and introduce into atmosphere in large quantities during production of energy and in transport. This factor leads to permanent increase of average temperature of air, sea and oceans, so called global warming.Nowadays large amount of data exists showing that the temperature of Earth in the last 150 years has been continually increasing. It represents about 03°C per ten years and the most of climatologist believe, that the increased concentration of greenhouse gases in the atmosphere is responsible for this effect.The most important greenhouse gas is carbon dioxide CO2. Majority of CO2 emissions comes from electric power stations working with fossil fuels, cars and industry. Burning of fossil fuels contribute up to 80% to world wide anthropogenetic emissions of CO2."

Jan 1, 2010

By Jiann-Yang Hwang

Hydrogen storage is a critical issue for the hydrogen economy. Current storage technologies are not able to meet the combined gravimetric, volumetric, and system cost targets set by the Department of Energy. To solve the problem, the development of a new material - perhydride ? is proposed. Perhydrides are defined as materials that contain more hydrogen atoms in their molecules than conventional hydrides do based on the valence. This concept is supported by the versatile bonding capability of hydrogen and the recent discoveries in the chemistry of hydrogen clusters.

Jan 1, 2006

By G. Coryell, E. Brack

"Remaining competitive in today's metal markets requires that copper smelters utilize the latest technology offered in process control, data acquisition, and process optimization. State-of-the-art tools like minicomputers, personal computers, and microprocessor based controllers provide real time process information that assist in making proper adjustments to the overall control strategy of an operating plant. The database accumulated by such systems broaden process knowledge, thereby reducing costly errors and plant downtime.IntroductionThe ASARCO Hayden Plant is located approximately 80 miles southeast of Phoenix, Arizona. The plant was commissioned in 1912 for the purpose of smelting copper concentrates from the surrounding mining district. Copper was produced for many years using calcining, reverberatory smelting and copper converting techniques. With the stricter environmental controls of the 1970's, the smelter experienced substantial declines in efficiency and productivity. It became necessary to identify and install a new smelting technology to maintain the viability of the Hayden plant.In 1980, after evaluating several smelting techniques, ASARCO management selected flash smelting as developed by International Nickel Company (INCO). One hundred and thirty-two million dollars was allocated for the project and construction began in 1982. Construction was completed and the new plant came on line in November of 1983."

Jan 1, 1989

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Kaspar Tall, Dmitri Goljandin, Kristiina Vilsaar, Jaan Kers, Valdek Mikli, Lifeng Zhang, Riho Tarbe, Viktor Laurmaa, Mart Saarna, Priidu Peetsalu

In this paper, the mechanical milling of the Printed Circuit Boards (PCB) was carried out. First goal of the work was to examine the management of the WEEE, in particular the re-use of PCB. Firstly, recycling methods of PCBs were summarized. During the study mechanical separation methods (magnetic-, density- and air separaten), electrical, and chemical methods were examined. Secondly the optimal particle size for air-classification was determined. Several tests were carried out to find the most effective separation method for separation of different material groups from PCB scrap. The new air classification stand was developed for testing the separation of lightweight particles like tinfoil stripes and plastics. The test results showed sufficiently good separation of heavier Al and Cu. For milled materials characterization the SA, IA, laser diffraction analysis and SEM were used. The chemical composition of the PCB powders was studied by means of energy dispersive X-ray microanalysis (EDS).

Jan 1, 2011

By M. M. Salari Rad

An investigation of gold distribution in the mill products of Sar Cheshmeh beneficiation plant demonstrates that on average 44% of the gold is routinely recovered as a by-product in the copper concentrate, and the remaining is lost to the tailing. In order to evaluate the causes of gold losses, the distribution and mode of gold occurrence in the Sar Cheshmeh ore and mill products were studied. Searching for gold within samples and within individual grains of sulphide minerals was carried out by SEM in the backscattered electron mode and SIMS, respectively. The mineralogical distribution of gold revealed by microbeam techniques were combined with the results of relevant metallurgical experiments including, sizing, heavy liquid separation, and diagnostic leaching tests, and the nature and location of gold in the ore and mill products were determined. The combined results of the experimental approaches pursued suggest that while there are some gold in solid solution and/or -colloidal size within sulphides of the Sar Cheshmeh ores, "visible" gold is the principal form of gold occurrence at Sar Cheshmeh.

Jan 1, 1999

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By Donald L. Stewart, Ken Overfield, Edward M. Williams

"Recent increases in energy cost have lead to a renewed focus on energy efficiency during aluminum melting operations to reduce fuel usage. The goals of a batch melting operation are to melt the charge using the minimum required energy, to melt the metal to the required temperature within the required timeframe, and to avoid generating unwanted contaminants by overheating the charge.The heat transfer efficiency of a conventional hydrocarbon fired aluminum melting furnace varies over the course of the melt cycle, depending on the conditions in the furnace. The purpose of this work was to develop a method of determining the transient heat transfer efficiency throughout the furnace cycle and to take advantage of this knowledge to optimize the melting process through furnace controls and proper production operations. This furnace survey methodology has been developed and used to evaluate a number of furnaces.Description of a Typical Batch Melting Furnace CycleA typical batch melting furnace cycle will consist of three stages:1. Charging – Solid metal charged through an open roof, solid or molten charged through an open door, and/or molten poured through a furnace blister2. Melting – From the time the door or roof is closed and the burners are turned to high fire until the charge is all liquid and has reached a temperature suitable for alloying (typically ~1350 °F / 730 °C)3. Holding – From the end of the melting stage until transfer or casting is completeIn some cases, further charging can take place after the melting cycle has started. This can happen when the entire solid charge will not fit in the furnace in one load, or if additional molten metal is added while the charge is melting. The bulk of the energy used in the melter is consumed during the melting cycle. The thermodynamic minimum energy requirements for melting pure aluminum are:• Energy required to heat pure aluminum from room temperature to the melting point at 1220°F (660°C) is 288 BTU/lb (670 kJ/kg)• Energy required to change state of pure aluminum from solid to liquid (heat of fusion) is 171 BTU/lb (397 kJ/kg)• Energy required to heat molten from melting point at 1220°F (660°C) to 1350°F (730°C) is 36 BTU/lb (83 kJ/kg)• Total energy required to melt a solid charge from room temperature to 1350°F (730°C ) is 495 BTU/lb (1151 kJ/kg)"

Jan 1, 2009

By Ruben Alvarado

The need to increase business competitiveness while complying with environmental requirements represent the great challenge that the Caletones smelter has decided to face in a new development project with a compromising and willing alliance with its workers. To date, the project is at the feasibility stage, with start up scheduled for the middle of the year 2002. The processing capacity of the Teniente Converters will be increased to levels up to 2400 tpd of chalcopyrite-based concentrates containing 30% Cu, by means of more intensive use of oxygen and improved stabilization of the overall operation. Productivity increses in the converting of white metal and the pyrometallurgical treatment of slag are also planned. As a result of related strategies, the productivity of the supporting facilities, included the capacitiy of the sulfuric acid plants, will be increased. An intensive and well-designed labor-upgrading scheme will allow the transformation of every worker into an expert in his working areas, thus becoming an active driving force in technology development. Mechanization, appropiate infrastructure, and complete process control and instrumentation will give to the skilled and motivated personnel the necessary tools in order to attain the highest potential ever reached with the Teniente technology. The necessary investment for this project based on the adding facilities to the existing plant is only a third of that required to reach the same objective for a greenfield plant, thus yielding a very high return on investment.

Jan 1, 1999