Search Documents

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012

By Leonard A. Duval

This concept employs a viable energy saving method that uses a solvent to separate oil from particle matter; it can be used in metal forming industries to deoil sludges, oxides, and particle matter that is presently committed to landfill. If oily particles are used in their oily state, severe consequences to environmental control systems such as explosions or filter blinding, occur in the air handling equipment. This is due to the presence of hydrocarbons in the stack gases resulting from the oily particles. After deoiling, the particles can be recycled and the separated oil can be used as a fuel. The process does not produce a waste of it's own and does not harm air or water. It demonstrates the dual benefits of being commercially viable and in the national interest of conserving resources.

Jan 1, 1994

By Roberto Javier Santiago

This paper tries to make a study about the use of calcium carbide during the tapping in replacement of part of the aluminum used in the furnace tapping, analyzing theoretical consumptions and then transfering the practice to the plant.

Jan 1, 2006

By Takashi Nakamura

Dismantling and detachment of parts from e-scrap are essential and involve higher cost techniques in pretreatment processes for physical separation. New techniques are desired for effective recycling of minor rare metals, therefore, we are trying to develop new detachment processes such as a new break down process. The principal of this new process is an electrical disintegration by electric pulse. E-scrap is broken down by high voltage electric pulses in water. IC chips and LSI can be detached from printed circuit boards under proper conditions. Ta- capacitors are also broken down to plastic parts and Ta sinter with lead wire. This is very useful in terms of pretreatment for e-scrap recycling. Also in the case of metallurgical production, with its intrinsic potential of smelting, extraction, enrichment and separation methods, play an important role in the context of minor rare metals.

Jan 1, 2015

By Tim B. Vanderwood

The mineralogy of dusts from several locations in a lead smelting plant, remotely collected dusts and soils near the lead smelter, and dusts from a secondary copper smelter were examined by reflected light microscopy (RLM) to determine their m1neralogy, texture, and origins. Individual grams were further analyzed by microbeam techniques. Detailed petrographic analysis of the dust has been supplemented by automated scanning electron microscopy combined with energy dispersive x-ray spectroscopy (ASEM-EDS). This technique allows the rapid sizing and chemical analysis of thousands of individual particles in a dust sample, producing particle size distributions as well as statistically meaningful breakdown of a sample into chemical types (e.g., proportion of galena vs chalcopyrite).

Jan 1, 1992

By Jitka Jandová

In this study, hydrometallurgical processing of waste ZnO flue dust arising during zinc removal from galvanized low-alloy steel sheets was investigated on a laboratory-scale to obtain electrolytic zinc. The flue dust was separated from flue gases, generated during heating waste galvanized steel sheets in an electric furnace under air atmosphere at temperatures of about 1000oC. The dust, comprising tetragonal ZnO and insignificant amounts of SiO2, was contaminated by Fe, Mn, Pb, Al, Mg, Pb, Cu and Ca. The dust was leached in 0.5 and 1.0M H2SO4 and/or in 20 and 30% NaOH at different temperatures and different liquid-to-solid ratios to determine the optimum conditions leading to the highest possible selectivity of leaching and efficiency of Zn extraction in minimum time. The subsequent electrowinning process was performed with refined zinc sulphate leach liquors and/or with untreated zinc caustic solutions. Zinc sulphate leach liquors were purified using a combination of a hydrolytic pH-controlled precipitation, cementation and carbon refining. Effects of operational variables on Zn electrowinning have been studied for both sulphate and caustic electrolytes. The conventional plate-plate electrowinning cell has been explored in this study. Comparison of results obtained for both zinc electrowinning from acid sulphate and alkaline solutions is presented contribution.

Jan 1, 2003

By L. Sh. Tsemekhman

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By J. N. Kondo, M. Hara, T. Smida, N. Ooto, K. Domen

"A porous material composed of two-dimensional anionic sheets of a layered perovskite, KSrNb30 10, was studied as photocatalyst for the production of Hz in the presence of alcohol sacrificial donors. Colloidal single and multi-layered HSr2Nb30 10 sheets were formed by intercalating ietra(n-buthylammonium) cations into the interlayeres of H+-exchanged KSr2Nb30 10 (HSr2Nb30 10), and addition of HN03 solution to the colloidal suspension precipitated the porous materials in which HSrNb30 10 sh~ets rand~mly stuck together. Original HSr2Nb30 10 before exfoliation had a BET surface area of 1 m2 g-1, whereas the surface area of a porous material prepared under optimal conditions exceeded 100 m2 g-1. The porous HSr2Nb30 10 had considerably higher photocatalytic'activitie8 for oxidation of 1-propanol and 1-buthanol than HSr2Nb39io, indicating that in the porous materials many niobate sheets are available for decomposition of these large alcohols.IntroductionQuite a research effort has gone into the design and study of porous materials. Such materials with large surface areas would have applications in highly efficient adsorbents or catalytic reactions.We have been studying photocatalytic reaction by cation-exchangeable layered metal oxides, where alkali metal cations are intercalated into the interlayers of inorganic sheets.[1,2] There are several advantages to using layered compounds rather than bulk powders for photocatalysis. Layered compound is rich in variety, in addition, modifications of them are easily performed by exchanging alkali metal cations in the inter layers for H + or other metal cations. The most important advantage is that some layered compounds have considerably high photocatalytic activities than bulk catalysts because the electrons and holes generated in each thin inorganic sheet readily reach interlayer spaces as reaction sites at the illterlayer spaces. It should be very important for further improvements· of layered photocatalysts to utilize two-dimensional inorganic sheets effectively."

Jan 1, 2000

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By G. A. Eltringham, A. F. Sarofim, A. A. Shook, M. P. Heap, B. R. Adams, K. A. Davis

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the different temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The improved kinetic parameters derived from the drop tube studies are used to simulate chalcopyrite concentrate reactions in the reaction shaft of an industrial smelter. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By R. Hurman Eric

The electrode in a slag-resistance electric furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power, i.e. heat needed for the operation. The control parameters are the size and positioning in the slag bath which are defined by slag resistivity, furnace resistance, cell constant and power input sequence all of which are closely interrelated. The flow of heat generated by the electrode current determines the energy distributions and thus the furnace dimensions. Heat flow models concerning vertical, horizontal and combined two-dimensional flows are discussed. All these considerations are based on the experimentally determined slag properties such as its resistivity.

Jan 1, 1995

By Run-boWang, Fan-yi Meng, Jian-Liang Zhang, ZheWang

To elucidate the influence of high Al2O3 content on sinter softening and melting behavior, heating-up reduction test under load was carried out. In addition, microstructure study of sinter bed structure change at a different temperature was also made and the mechanism that the effect of Al2O3 content on sinter softening and melting property was discovered. SEM results showed that the increase of Al2O3 content favored the formation of Al2O3-rich slag phase, such as the eutectic (2CaO·SiO2-2CaO·Al2O3·SiO2-FeO) and gehlenite (2CaO·Al2O3·SiO2), resulting in the decrease of sinter Ts temperature. Further, high Al2O3 content improved the concentration of metallic iron and lowered the dripping temperature due to the decrease of slag liquidus temperature and viscosity. At a fixed basicity, it was indicated that there was a relationship between Al2O3 content and sinter softening-melting property. Based on the results, counter strategies to cope with the adverse effect of high Al2O3 content on the cohesive zone property were also proposed. It could provide guidance for the blast furnace operation of sinter with high Al2O3 content.

Jan 1, 2015

By Tuneo Funahashi

Sumitomo Shisaka Works has been treating EAF(Electric Arc Furnace) dust to recover zinc and lead in the Waelz Kiln process. Since its commencement of operation in 1977, many technical improvements have been successfully made to increase the production capacity and the zinc recovery rate. The EAF dust charge to the Waelz Kiln was increased from 35,000tly to 120,00OtIy, and the production of zinc oxide now amounts to 40,000tly. The zinc content in the clinker was decreased from 5% to less than I%, by the optimization of the kiln heat pattern with no accretion trouble. And the clinker has become more a valuable raw material for steel making. This paper describes the above progress ofthe SMM Waelz Kiln process operation at the Shisaka Works.

Jan 1, 1998

By J. Partinen

Drying is a unit process which has numerous applications in metallurgical process industry. Kumera Technology Center, being a worldwide equipment and process supplier, has developed sophisticated solutions for both direct and indirect drying. In conventional direct drum drying, the energy is taken from combustion of fossil fuels, requiring energy input and emitting considerable amount of off gases. In modem copper smelters, thermal energy from the off gases is recovered in waste heat boilers making the steam available. Using that steam as the energy source for concentrate drying, the total volume of off gases can be considerably reduced and releasing of harmful combustion gases into the atmosphere can be avoided. Kumera Technology Center has recently developed and promotes a new steam drying process for drying of copper concentrates. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the steam dryers and the drum dryers. In the design special attention has been paid to overcome problems of excessive wear and clogging and to reduce the required maintenance operations. In this paper the environmental issues and energy consumption related to both direct and indirect drying processes are discussed. The estimated operation costs and emission levels are compared, based on calculations and the data collected from industry. Finally, the development project of the Kumera Steam Dryer is briefly reviewed

Jan 1, 1999

By H. Y. Sohn, Haitao Wang, Moo Eob Choi

"A novel ironmaking technology is under development at the University of Utah. This technology produces iron directly from iron ore concentrate by gas-solid suspension reduction. Hydrogen is the main reducing agent for high reactivity and for the elimination of carbon dioxide release in this ironmaking process. The direct use of concentrates allows bypassing the problematic pelletization/sintering and cokemaking steps in the steel industry.Intrinsic kinetics of the suspension reduction of magnetite concentrate particles by hydrogen has been measured. Experiments were carried out in the temperature range of 1423-1673 K, other experimental variable being hydrogen partial pressure, the amount of excess hydrogen and particle size. Under most experimental conditions, 95% reduction was attained within several seconds, which presents sufficiently rapid kinetics for a suspension reduction process. The reaction kinetics followed the nucleation-and-growth equation, and a rate equation that contains all the effects of the experimental parameters has been obtained.IntroductionWith the rapid increase in steel production, it is critical to control CO2 emissions which is the main greenhouse gas. It is inevitable to release a huge amount of CO2 when coke and/or coal are used as the main reducing agent in producing iron. As one of the methods to reduce the CO2 emission from ironmaking, the utilization of the gaseous reducing agents and fuels, including hydrogen, has been investigated [1-6]. The use of such gases forms the basis for a new ironmaking technology under development for producing iron directly from fine concentrates by a gas-solid suspension technology. This technology would reduce energy consumption by about 40% of the amount required by the blast furnace and drastically lower environmental pollution, especially CO2 emission, from the steel industry [4]. This is accomplished by adopting H2-based reductant and bypassing pelletization/sintering and cokemaking steps. Unlike other gas-based alternative ironmaking processes using shaft furnaces or fluidized-bed reactors, the suspension reduction technology is a high-intensity process because it will not suffer from the problems that other processes do when operated at high temperatures mainly from the sticking and fusion of particles."

Jan 1, 2011

By Garry W. Warren

The brass foundry industry produces a significant amount of waste sand containing Cu, Zn and Pb which is often classified as a hazardous waste due to Pb content. The potential application of a hydrometallurgical process to treat the sand by extracting metal values and thus detoxifying the material has been investigated. The process involves leaching of metal values followed by cementation. The emphasis of this investigation was on the leaching step, although some preliminary cementation experiments have been performed. In order for any alternative treatment scheme to be successful, the smaller size fractions of the sand must be addressed. Experiments have been performed on five individual size fractions using various lixiviants HCI, acetic acid and HCI/NaCI. Cu extraction was found to be slower than either Zn or Pb. Results obtained in this investigation indicate that copper is present in two forms, an oxide form which dissolves rapidly and is insensitive to the level of oxygen, and a less soluble form, probably metallic which dissolves more slowly and requires an oxidizing agent. The presence or absence of oxygen had no influence on the rate of Zn dissolution indicating that zinc is present mostly in oxide form. Toxicity Characteristic Leaching Procedure (TCLP) tests showed that residues could be produced which meet the toxicity limit for lead. Preliminary cementation experiments have also demonstrated the feasibility of Cu and Pb recovery.

Jan 1, 1991

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at 1300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt"10 iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003