Search Documents

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By Manfred K. Walther

"Tests were conducted on instrumented plates cast in the Abex Experimental Foundry to compare recorded solidification histories with results computed for corresponding models simulated with the C.A.S.T. program. The first plate was cast of low alloy steel and the second of carbon steel with a graphite chill at one end. Both were cast in molds of bonded silica sand. Temperature histories were recorded in the castings, molds and chill. Exceptionally good agreement was achieved between computed and experimental data. Other investigators will find the results useful as a benchmark against which they can compare the results of their own calculations.IntroductionSince the early 1970's our foundry engineers have used both two- and three-dimensional versions of the G.A.S.T. program to gain knowledge of the solidification process [1,2,3]. Study of the computed data gave insight as to how the rigging and risering of specific castings might be changed or adjusted to improve quality and yield. New schemes based on such analyses were then recommended for implementation on the foundry floor. The degree of success of the new practice was subsequently evaluated after the part had been poured, shaken out and examined. Similar conditions were noted in the sectioned castings whenever porosity and voids had been predicted by the computations. Appropriate modifications, when found successful in the model, were applied to the process. This led to a reduction, if not complete elimination, of the defects. Such results gave credence to the use of these programs as an aid in the production of better castings.Earlier investigations on simple shapes revealed excellent correlation between output derived with the G.A.S.T. program and exact solutions. Results also compared favorably with data calculated using other codes as reported in the literature [4] and summarized in the Appendix. However, since the computer program had not been verified by direct experiment, it was decided to run instrumented tests to check the theoretical predictions with actual measurements."

Jan 1, 1986

By Barry T. Kilbourn

There is a continuous quest for better-performing materials, for example, to withstand higher temperatures, to resist more efficiently degradation or to be electrically conductive under extreme conditions. The oxides, and similar compounds, of the lanthanides and yttrium can, in some cases, help provide such behavior. Other advanced materials, such as hydrocarbon catalysts, optical ceramics or sensitive phosphors, may also require these oxides for some essential function. The role of the oxides in a wide variety of technologies, some novel and developing, will be reviewed and the underlying physico-chemical principles, the common threads, between several less well-known and apparently unrelated uses discussed.

Jan 1, 1989

By W. G. Davenport

Chapters 7,8and 9 calculated three combinations of: blast composition (mass% O2, mass% N2) oil quantity per tonne of concentrate blast temperature that will steadily produce molten 65% Cu matte from pure chalcopyrite-concentrate. The combinations are:

Jan 1, 2001

By Elsa Olivetti, Randolph Kirchain, Gabrielle Gaustad

"As scrap usage increases, it is often necessary to “dilute” the melt with primary aluminum to ensure the finished product meets compositional specifications. Secondary raw materials, particularly postconsumer scraps, often include high levels of unwanted or “tramp” elements, such as iron and silicon in the case of aluminum. Recent literature on this issue cites several causes including inherent contamination during processing as well as ineffective segmentation at end-of-life. To address this accumulation problem, “upgrading” solutions have been developed including: dismantling of end-of-life products, spectrographic or magnetic sorting of shredded scrap, and “filtration” technologies that remove tramp elements in the melt. Although it is clear that upgrading strategies enable increased usage of scrap, it is not clear that they would be economic or efficient. This work presents a set of analytical methods, based on chance constrained optimization, to quantify the potential environmental and economic value of several scrap upgrading technologies.IntroductionAluminum recycling has a number of key environmental and economic benefits. Compared to other materials, aluminum production has one of the largest energy differences between primary and secondary production: 175 MJ/kg for primary compared to 10-20 MJ/kg for secondary[1]. With energy and cost savings in mind, many producers now have targets of increasing their usage of secondary materials[2, 3]. However, the accumulation of impurities in these recycled material streams provides a significant compositional barrier to these goals[4].A growing number of studies and literature would suggest that accumulation of unwanted elements is a growing problem, in all recycled material streams. In the case of aluminum, the list of problematic impurities is quite large, including but not limited to: Si[5, 6], Mg, Ni, Zn, Pb, Cr[7], Fe[5-7], Cu[6, 7], V, and Mn[6]. Metals recycling is a metallurgical process and is therefore governed by the laws of thermodynamics. The removal of unwanted elements in the scrap stream is dictated by the energy considerations of the melt process. Compared to many metals, aluminum has a high degree of difficulty in the removal of tramp elements, due to thermodynamic barriers. Therefore, with no simple thermodynamic solution, producers must identify strategies through-out the production process to mitigate this elemental accumulation."

Jan 1, 2008

By T. Johnson, B. Q. Li

"Electromagnetic stirring has found a wide application in metals processing for the benefit of obtaining refined solidification microstructures. This paper presents an experimental study on the melt flow and turbulent behavior in an electromagnetically stirred Woods metal pool. The experimental setup consists of metal bath unit equipped with temperature control to allow both cooling and heating, velocity probe positioning unit and data and signal acquisition and processing unit. The whole measuring system is under the control of an IBM personal computer. Velocity measurements are made using the incorporated magnet probes, which are calibrated using a turntable. The measured results showing the effect of the coil positions, coil arrangements and the applied currents on the melt flow are presented. Both mean flow and turbulence quantities are discussed.1. IntroductionElectromagnetic stirring is widely practiced in the metals industry for melt mixing and for casting microstructure refinement. Industrial examples are taken from induction furnaces where the electromagnetic forces are applied to generate desired melt mixing and also various types of electromagnetic stirrers used in various stages of steel and/or aluminum casting processes to produce fine grain solidification microstructure or to eliminate undesired defects such as TCG (twinned-columnar-grain) structure. For ultrahigh purity aluminum or high strength aluminum alloys containing zirconium or lithium, grain refinement can be difficult with the conventional technique, and electromagnetic stirring provides a particularly powerful means to obtain the refined solidification microstructure [1]. A fundamental understanding of the melt flow and the turbulence characteristics in these magnetically-driven flow systems is of significant engineering importance to both process design and product quality improvement.There exists extensive literature on the magnetically-driven melt flows in material processing systems. Nakanish. et al. [2] were perhaps among the early investigators to mathematically and physically model the magnetically-driven flow phenomena in molten metal systems. Subsequent theoretical and experimental work by Tarapore and Evans [3, 4], Szekely and Chang [5], Hunt and Moore [6] and Szekely and El-Kaddah [7] has contributed very significantly to our understanding of magnetically-driven flow in inductively stirred melts. They have developed mathematical models for the electromagnetic field and turbulent flow in induction furnace and validated the models by either laboratory experiments or direct measurements in the industrial-scale induction furnaces."

Jan 1, 1998

By Dong Liang, Honggang Zhong, Zhenxing Yin, Qijie Zhai

"2507 super duplex stainless steel (SDSS) has been widely applied in a marine environment, attributing to its excellent pitting corrosion resistance and mechanical properties which are particularly determined by the nitrogen precipitation behaviors and volume fraction of ferrite. In this paper, various cooling rates were obtained by applying four different moulds with the common gating system. By which the influence of cooling rates on nitrogen precipitation behaviors and the ferrite fraction in cast 2507 SDSS was comparatively investigated. The results showed that nitrogen porosity could easily precipitate in cast 2507 SDSS under standard atmospheric pressure. The number of nitrogen holes increased with decreasing the cooling rates, and the holes mainly distributed in three zones, i.e. the interface between the horizontal and vertical columnar grains, top vertical columnar grains and the final solidification region. Additionally, higher ferrite fraction was obtained with lower cooling rates.IntroductionDuplex stainless steels (DSS) have a dual-phase microstructure consisting of ferrite (d) and aus-tenite (?). Due to the combined advantageous properties of d and ? phase, their application rapid-ly increased in industry [1, 2]. Super duplex Stainless Steel (SDSS) is the third generation of du-plex stainless steels, of which the alloy elements Cr, Ni and N content are higher than the stand-ard 2205 DSS. Because it has high contents of alloy elements, the SDSS has better mechanical properties, and its pitting resistance equivalent number (PREN) reached a point 43. Hence SDSS has been used in petroleum chemical industry, the marine equipment and harsh corrosion environments [3]. SDSS contains ferrite stabilizing elements, such as Cr, Mo and Si, and austenite stabilizing elements like Ni, Mn and N [4]. Many researchers have studied the effects of these elements on the stabilization of d and ? phase and the ratio of the two phases. High nitrogen con-tent is another prominent feature of SDSS. Nitrogen addition to SDSS is very effective for improving its mechanical properties [5] and corrosion resistance [6], such as pitting resistance in NOx environment. To increase the nitrogen content in steels, a lot of work had been done. N. Nakamura and S. Takaki [7] examined the behavior of nitrogen absorption in Fe-23Cr alloy powder by sintering in nitrogen gas atmosphere, they found nitrogen content easily up to 1.0 wt. %. Using devised NH3 gas injection system, W. Park et al. [8] successfully produced austenitic Fe–23.5Cr alloys containing over 3 wt. % of nitrogen. Further-more, W.P. Tong et al. [9] stated that nitrogen percent was extraordinary high (about 10 wt. %) in pure iron plate. However, the above methods are difficult to be applied to large-scale industrial production."

Jan 1, 2012

By Dong Liang, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"The formation, distribution and survival of pure Al nuclei under surface pulsed magneto oscillation (SPMO) treatment were investigated with thecombination of experiments and numerical simulation. The results indicated that the nuclei originated from the whole top surface of melt owing to the oscillation of top surface induced by SPMO. The temperature field significantly affected the survival of the nuclei The electromagnetic force and flow field of the melt with SPMO treatment were simulated by finite element software ANSYS. The electromagnetic force mainly distributed below the top surface near the mould wall. The electromagnetic farce not only made the melt oscillate but also increased the convection of meh below the top surface vigorously. The oscillation near the top surface of the melt promoted the nucleation largely, and the convection increased the uniform of the temperature distribution in the whole meh which favored the survival of nucleiIntroductionAs we all know, fine equiaxed grains are beneficial fur the improvement of the mechanical property, process ability and the uniformity of metallic materials [1-2]. With the researches of recent decades, people discovered that the electromagnetic field is an efficient method to refine the solidified structure of metals [3-7]. Pulsed magnetic field technology obtains more and more attentions in recent years due to its smaller power consumption, bigger instantaneous magnetic field intensity, non-contacting with the meh and simple convenient equipment manufacturing [8-9]. However, the melts would splash fiercely when pulsed magnetic field is applied with a slightly higher power. Thus, based on the understanding of the solidification refinement mechanism of electric current pulse (ECP) [10], Gong et al [11] developed a novel technology called pulse magneto-oscillation (PMO) to refine the solidification structure. The technology can be easily applied in the solidification structure refinement of continuous casting slab. But fur aluminum continuous casting, the sump is very shallow, which greatly limits the application of pulse magneto-oscillation technology."

Jan 1, 2014

By Itavahn Alves da Silva, Izabela Diniz Duarte, Carlos Antonio da Silva, Varadarajan Seshadri

Mathematical modeling using computational fluid dynamics has been employed to assess the thermal losses in a steelmaking ladle. Thermal losses lead to thermal stratification and convective flow inside the ladle. The effects of preheating, mineralogical and physical characteristics of the lining as well as thickness of slag cover have been studied and the results obtained from application of the model have been discussed.

Jan 1, 2016

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By Alexander V. Suvorin, Vladyslav M. Sokolov

"The traditional technologies for production of the coprecipitated and deposited catalysts are analyzed from the standpoint of diversion of application of the feedstock and increase of efficiency for its usage. The options for return of the metals of spent catalysts to the catalysts production are described. The novel environmentally friendly and cost efficient approach for reutilization of the spent catalysts is realized in practice. It anticipates application along with spent catalysts of the waste generated in the catalytic productions. Reutilization of the Ni-containing catalysts is referred as an illustration. Introduction The recent development of large catalytic manufacturing for organic and inorganic synthesis, and petroleum refinery as well as for applied environmental catalysis has brought about increase and diversification of catalysts production. The generation of spent catalysts has been increased correspondently. The feedstock for production of catalysts is mostly metals in a form of nitrates, carbonates, hydroxides, hydroxydcarbonates. Sometimes salts of organic acids, of ammoniates, of chlorides and of sulphates occur. All these materials are scarce and expensive. So their repeated use by reutilization of spent catalysts is very actual issue. The traditional recycling the Fe-, Cr-, Ni-, Cu- or Zn-containing spent catalysts are carried out by pyrometallurgical reclamation of pure metals or alloys. They can not be used directly in production of catalysts [1, 2]. The hydrometallurgical approach is used for recycling spent catalysts with PGM, W, Mo, Co, Ni or Cu. It provides production of salts of these metals in a form of sulphates, chlorides, carbonates, hydroxydcarbonates and sometimes nitrates or ammoniates. Only a limited number of these salts can be used directly in production of catalysts. Material losses during catalysts production The basic feedstock for manufacturing coprecipitated and deposited catalysts that may be produced from the spent catalysts is aqueous solutions of metals nitrates. Their production is based on application of nitric acid as a dissolvent. About half of it is lost with the flue gases in a form of nitrates vapor and nitrogen oxides (II, IV). The last compound is generated by reaction:"

Jan 1, 2008

By Hiroshi Tabuchi, Akihiko Takahashi

"High strength aluminum matrix composites were prepared and studied using as reinforcement newly developed nearly mono-dispersed a-alumina single crystal particles each of which has a regular polyhedral shape. The composites were formed by centrifugal casting using aluminum casting alloys (Al-Si and Al-Cu-Mg) as the matrices, followed by heat treatment. The volume fraction of the alumina particles was as high as 60%. The same matrix composites reinforced by conventional crushed fused alumina particles were similarly prepared as the reference. The bending strength and tensile strength of the Al-Cu-Mg matrix composites reinforced by the novel alumina particles of 10 µm in average diameter are as high as 1020 MPa and 560 MPa, respectively, which are higher than those of the conventional alumina composites. Furthermore, the bending strength of the novel alumina composites degraded less than that of the conventional alumina composites after thermal fatigue tests. The number of cracks in the matrix seemed to influence the thermal fatigue property because many cracks were observed in the conventional alumina composites, whereas only a few cracks were observed in the novel alumina composites. This was confirmed by SEM observation of the sample composites before and after the thermal fatigue tests.IntroductionAluminum matrix composites strengthened by dispersed reinforcements are of interest for various applications due to their improved properties, such as high specific strength and stiffness, wear resistance, etc .. A large number of investigations have been made concerning fabrication processes and properties of these composites. With regard to the fabrication processes, powder metallurgy has been well-known as a solid phase process, and recently many liquid phase processes such as a compocasting, a squeeze casting, the Lanxide process, and the Osprey process have been studied and developed.(1)"

Jan 1, 1998

By A. V. Tarasov

Investigations of thermodynamic properties of Cu-Ni and Cu-Ni-S systems and mattes have been conducted with the aid of a MC-1301 mass-spectrometer designed for studies-of processes of vapor formation of hardly volatile substances. The instrument comprised a combination of an evaporator of Knudsen chamber type with a mass-spectrometer for analysis of the vapor phase, In the process of studies of molten Cu-Ni-S systems and commercial-grade mattes within a temperature interval of 1400-1800 K the partial pressure of sulfur was measured by means of complete isothermal evaporation and the partial pressure of copper and nickel by comparison of ionic currents. The partial pressure values of the components above the molten Cu-Ni-S were used for calculation of activities of the respective components in the melt. The copper and nickel activity data obtained was used for assessing the amount of dissolved losses of these metals in autogenous smelting slags.

Jan 1, 2003

By W. F. Ranson, R. C. Progelhof

"I. THE PROBLEM: MANUFACTURING PRODUCTIVITYThe 1985 President's Commission [I] on Industrial Competitiveness found compelling evidence of the declining economic position of the United States in world markets. The annual rate of increase in the United States productivity is approximately one-seventh that of our major trading partners over the last decade: profit levels in manufacturing investments are below those of the mid-1960's; an increasingly negative trade balance since 1971; and a sharp decline in the United States share of world trade in manufactured goods for more than two decades. A particularly dramatic example of the shifting economic balance is the fact that Japanese productivity growth has been five times greater than that of this country since 1960. In face, Japan's productivity now exceeds that of the United States in such critical industries as steel, transportation equipment, electronics and electrical machinery.American employees have experienced the competitive consequences of this nation's lagging industrial performance. Between 1980 and 1984 alone, the population of non-farm employees engaged in manufacturing dropped from 22.4% to 20.6%. This reduction in manufacturing must be arrested.Commissions RecommendationsThe comprehensive set of recommendations offered by the President's Commission recognized the nation's ""key competitive advantages"", technology and human resources, and calls for their strengthening. Particular emphasis is placed on manufacturing technology and the fact that this country does not translate research into new technologies rapidly and fully.""Perhaps the most glaring deficiency in America's technological capabilities has been our failure to devote enough attention to manufacturing or 'process' technology. It does us little good to design state-of-the-art products if within a short time our foreign competitors can manufacture them more cheaply. The United States has failed to apply its own technologies to manufacturing. Robotics automation and statistical quality control were all first developed in the United States but in recent years they have been more effectively applied elsewhere""."

Jan 1, 1988

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By W. Persson

The first installation at a copper smelter of a Semtech OPC System for continuous, on-line production control of copper converting in PS converters took place in 1994. At present OPC systems are installed at 19 PS converters. The technology presents to the operator real-time information on the progress of the process he is controlling in the form of optical process parameters, thus facilitating dynamic process control. The optical process parameters are based on time- and wavelength resolved registrations of the light emitted by the off-gas flames and identification of correlation between these parameters and characteristic metallurgical process data. The present paper provides a description of the technology as seen by the furnace operators and a summary of operating experiences made during five years of full-scale, operation at various smelters, reviews influences from the technology on smelter operational practises and comments on recent developments as regards new applications of the technology.

Jan 1, 1999

By C. Wieckert

Concentrated solar energy can be used as heat source for the production of metals. One of the most promising respective processes, the solar carbothermic production of Zn from ZnO, is investigated within the European research project SOLZINC, a cooperation of institutes and industries from France, Germany, Israel, Sweden and Switzerland. The solar produced Zn can be used as commodity or as an energy carrier for further processing on demand to electricity in Zn-air fuel cells/batteries or to generate hydrogen by reaction with steam. In both cases the Zn is oxidized to form ZnO, which can be recycled back to the solar plant. In these cyclic processes Zn acts as a means to store and eventually transport solar energy. Second product of the solar process step is a CO-rich offgas, which may e.g. drive a gas engine or may be shifted to hydrogen in a conventional reaction with steam. A pilot plant using 300kW concentrated solar power input has been constructed and operated successfully. 86mass-% of ZnO mixed with 14mass-% of charcoal are reacted to produce Zn and CO at a temperature of about 1200°C, yielding about 50 kg gaseous Zn per hour. Zn-dust with 95% purity is recovered from the offgas system that was designed to produce Zn for Zn-air fuel cells. Based on the results and findings from the pilot plant, a two tons Zn/h solar demonstration plant has been designed conceptually. Cost studies have been performed and scenarios for producing electricity or H2 via these ZnO/Zn-cyclic processes are evaluated.

Jan 1, 2006

By Petrus Christiaan Pistorius, Ming Tang

Magnetite concentrate is pelletized and then hardened by elevated-temperature oxidation to hematite, to produce pellets for ironmaking. Previous work showed that the rate of oxidation is under mixed control of gaseous mass transfer of molecular oxygen through the pellet pores, and solid-state diffusion into the oxidizing grains. Because of the partially limiting role of solid-state diffusion, concentrate size distribution strongly affects pellet oxidation. Previously, a simple mixed-control model was formulated to describe isothermal oxidation. In that model, the main effect of concentrate size distribution was on the plateau level of oxidation which is reached at a given temperature. However, the extent of plateau oxidation increases with increased temperature, requiring a more complex model for non-isothermal oxidation. In this paper, predictions of the non-isothermal model confirm the strong effects of concentrate size distribution and oxygen enrichment. In particular, a greater fraction of coarse magnetite particles would be beneficial, decreasing the size of the macroscopic unoxidized pellet core.

Jan 1, 2015

By W. L. Dalmijn, E. A. Schokker, N. Fraunholcz, P. C. Rem

Many processes developed for the mechanical processing of Automotive Shredder Residue (ASR) suffer from high processing costs. We offer a distinct concept for low-cost mechanical processing still allowing high value-added recycling of the recovered materials. The basic idea behind this approach is to produce saleable pre-concentrates at the lowest possible costs that can be further processed in existing separation facilities. Our process includes screening, size reduction and magnetic separation. Preliminary studies showed that fibers in ASR are magnetic due to adhering rust particles allowing separation into a fiber fraction and a non-magnetic rigid fraction by high-intensity magnetic separation. The fiber fraction is most suited for thermal processing. The rigid fraction mainly consists of plastics and rubbers with up to 10 wt.-% of non-ferrous metals, some inert material and copper wires. This fraction is very well suited for mechanical processing by, e.g., sink-float separation in existing metal separation plants. The non-metal fraction can be processed further to recover the plastics and rubbers. The process proposed in this study is expected to be substantially cheaper than full thermal processing. In addition, as it mainly relies on existing separation facilities, it can be applied in the short term.

Jan 1, 2000

By Jiang Fan, Liu Shi, Wang Haigang

Winter-time natural convection in gravel embankments has been suggested as a technique to provide passive cooling and thereby avoid thaw-settlement of roadways located in permafrost areas. Numerical simulation by finite volume method on the proposed model is perf9rmed using the software FLUENT. A gravels model, in which the embankment is composed of stones and air, has been adopted to investigate the temperature and velocity fields in embankment. Simulation results show that in summer, a weak clockwise circulation of the pore air extending throughout most of the embankment. The pore-air motion is very weak which results in relatively straight horizontal isotherm lines. And heat transfer is mainly maintained through conduction. But in winter, pore-air velocities are higher and multiple vortexes are formed in the embankment. Natural convection then becomes the dominant influence on the isotherm shapes within the embankment. As a result of low ambient temperatures exerted on the embankment surface during winter months, an unstable air density gradient develops within the embankment. This convection increases the heat flux out of the embankment. Therefore, the winter-time convection can further reduce the temperature of the foundation soil beneath the open-graded embankment. In addition, the effects of the size of the stones within the embankment have been analyzed and compared in the gravel model. It shows that in winter, 200mm stones lead to stronger vortexes in the embankment compared with those of 60mm stones. Consequently, the zone oflow-temperature beneath the embankment is extended.

Jan 1, 2004