Search Documents

By H. Ipek

In this study the effects of interstitial ratios on k-feldspar samples were investigated. The k-feldspar samples were taken from Egypt using dry batch grinding conditions and a kinetic model. Three different mono size fractions (-3350+2360, -850+600 and -300+212 µm) were ground separately for 0.5, 1, 4, and 8 minutes and at four different interstitial ratios (125%, 100%, 75% and 50%) using a Bond mill with a mixture of five ball sizes. The mill used was at a size of 30.5 cm diameters, with 30.5 cm length, providing a total mill volume of 22272 cm3. The mill has a total mass consisting of 22648 g. steel ball mixtures of 38.10, 31.75, 25.40, 19.05 and 12.70mm diameters, occupying 22% of mill volume. The mill rotates at a speed of 70 rpm. The weights of the feed charges were 3000, 2000, 1000, and 500 g for 125%, 100%, 75% and 50% filling of the interstices of the balls respectively. The specific rate of breakage (Si) was determined from the top size fractions at different grinding times that were mentioned above and the model parameters were compared for the four different powder filling ratios (U). In many investigations, it has been found that an interstitial filling ratio of U = 0.6-1.1 is a good powder ball loading ratio to give an efficient breakage in a ball mill. In this study, it was found that U=1.25 is a good ratio for K-Feldspar.

Jan 1, 2006

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"The structural and electronic properties of cubic d -NbN are investigated using density functional theory (DFT) and all-electron full potential linearized augmented plane wave method (FPLAPW). The equilibrium structural parameters are determined by fitting the total energy as a function of volume to the Murnaghan's equation of state. We calculated the total and partial densities of states (DOS) and compared them with those computed by different authors. Our DOS at Fermi level is found to be very close to the experimental value. The band structure is computed, discussed and used to find the characteristic energy separations. Valence electron density contours are recorded and discussed. We deduced the partial charge densities of different bands and binding energies of valence core levels and compared them with experimental and theoretical results obtained by different authors.IntroductionNiobium nitride has been intensively investigated over the last decades because of its interesting physical properties and technological applications (superconducting microdevices, microelectronic, catalytic probes, and hard coatings) [l]. While the group IV transition metal nitrides (TMN) mainly crystallize in the cubic NaCl structure (Bl type), those of group V and VI nitrides occur as different phases. Thus for niobium nitride, many phases have been reported in the literature: cubic fcc d -NbN, tetragonal ? -Nb4N3, hexagonal d -NbN, hexagonal e -NbN, and low nitrogen content hexagonal ß -Nb2N [l, 2].Structural and electronic properties of niobium nitride were investigated theoretically and experimentally by many authors. For example, in 1975 Schwarz [3] obtained the partial density of states for NbC and NbN from APW band structure calculations. In 1975 Kallne and Pessa [4] studied the electronic structure of Nb, NbC and NbN by using X-ray emission. In 2003 Amriou et al. [5] studied the electronic structure and bonding mechanism of NbC and NbN compounds using first principle total energy calculations using the full-potential linearized augmented plane wave method. Also in 2006 Sanjines et. al [l] studied the electronic structure of the hexagonal~Nb2N, hexagonal' d -NbN, and cubic d -NbN thin fihns by using X-ray photoemission spectroscopy. They [l] also calculated the densities of states for these phases and used them in the interpretation of the experimental valance band spectra. Most of these studies are old and there is a need for more recent studies. According to our knowledge, there are little comprehensive theoretical studies on this subject by using FP-LAPW method [5], which proved its ability to give accurate results. In this work we used the FP-LAPW method to study the structural and electronic properties of the cubic (fee) o-NbN (space group Fm-3m, prototype NaCl) crystal."

Jan 1, 2013

By Hans Prem

There has been a dramatic development in the field of magnetic materials in the last 10 to 15 years. Capacity improvement of electronic components especially required an increased production of "rare earth magnets", e.g. samarium-cobalt (SmCo) magnets and neodymium-iron-boron (Nd-Fe-B) magnets. We participated in this development and learned how to construct systems for the dry processing of these magnet materials. In the meantime we have supplied a large number of these systems for coarse and fine milling. Processing is effected in a protective atmosphere in order to avoid oxidation and thus deterioration of the magnet materials.

Jan 1, 1992

By Taner Kavas

In the present study the utilization of coal ashes that appear at the end of firing process of brick production in cement pastes was examined. Ashes with three different particle sizes of 75 µm, 106 µm and 150 µm were used to replace ordinary Portland cement (PC) as 5 % and 15 % by weight. Seven samples were prepared and physical, mechanical, chemical and microstructural analyses were carried out. The compressive and bending strength values of samples were determined at the ages of 2, 7 and 28 days. It was found that cementitious pastes with finer particle sizes possessed the highest compressive and bending strength values at all curing ages. Both values after 2 and 7 days cure increased with an increase in ash content, no matter what the particle sizes of ashes were. However, strength decreased after 28 days cure as a result of ash addition of 15 %, although it was still above that of the PC.

Jan 1, 2006

By Markus A. Reuter, Antoinette van Schaik

"Product design engineers select from a wide range of materials and combine them into multimaterial product designs. These include various materials (metals and non-metals) which are complexly integrated (e.g. welded, glued, alloyed, layered). The recycling/recovery rate of consumer products are determined by the different materials and alloys used, but also by the particle size and multi-material particle composition after shredding (combination of materials due to design). Eco-design (for recycling) and Design for Recycling (DfR) can only be conducted if the interconnectivity of material/metal in various unliberated materials is accounted for and its effect on material and energy recovery can be linked back to design. This paper will discuss the basic principles of these DfR models and it is shown how these tools (i) are linked Computer Aided Design (CAD) and Life Cycle Assessment (LCA) software, (ii) affect conceptual design specifications of products, (iii) integrate the complex detail of the recycling system and recyclate quality and hence (iv) make recycling an integrated part of the product system. Furthermore, it is shown how these assessment tools and models can be applied for benchmarking of the recyclability and environmental damage created by the recycling of end-oflife consumer goods in order to e.g. (i) provide the (original) equipment manufacturer with knowledge and solutions to support product stewardship and Extended Producer Responsibility; (ii) create awareness of the consequences/benefits of design, products and recycling systems to manufacturer, designer, legislator, recycler etc.; and (iii) assist the consumer in their choice of consumer goods from an end-of-life point of view.IntroductionA first-principles basis is required in order to be able to simulate and predict the recycling/recovery behaviour of products facilitating Design for Recycling (DfR) and Eco- Design. This links recycling technology and the environmental consequences of recycling directly to product design."

Jan 1, 2008

By Anette Mueller, Thomas Schnellert, Sérgio C. Angulo

"The use of automatically sorting technique, to separate gypsum components from recycled material of processed construction and demolition waste (C&DW), is motivated by environmental and economical aspects. Only if the gypsum can be separated the aggregates can fulfill the environmental requirements and also the structural characteristics according to the standards. Furthermore, the separation of red brick can also improve the quality of the aggregates.This paper aims at analyzing the separation of gypsum components and red brick by using the color sorting technique. The impacts on the composition and the envelope density of recycled aggregates are described. Depending on the gypsum content the application of two processing stages (rougher-cleaner) can be necessary to produce aggregates with sufficiently low gypsum content. Additionally, the separation of red brick and concrete is successful. So, the color sorting may be a promising technique to upgrade the quality of mixed C&DW aggregates.IntroductionConstruction and demolition waste (C&DW) is a mixture of different materials. Such mixtures can be used only in low grade applications. If the material is used as certified material for road construction or as aggregate in concrete the concrete particles must be separated from the other building materials. This paper aims at analyzing the separation of gypsum components and red brick by optical sorting. The needed stages of sorting for getting a product quality according to the German Standards are deduced.Gypsum is a building material that is increasingly used for interior works in Germany like it is shown in figure 1 [1]. At present the content of gypsum in C&DW is estimated at about 1 %. Assessments on the basis of material streams of gypsum and concrete and their life spans show that higher gypsum contents of about 3 % must be expected in future [2]. Also in other countries the use of gypsum has grown considerably in the last decades. From the characterization of C&DW available in some cities in Brazil, 4 to 15 % of total amount of C&DW that may arrive at the recycling plant to be processed is excessively contaminated by gypsum. In one of these cities, the average content of gypsum in the C&DW before processing was as high as 2.1 % [3]."

Jan 1, 2008

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By Pertti Pekkala

Outokumpu has 25 years of experience in the SX area. The development of the solvent extraction plants responds to an ever increasing demand for lower operational costs wd for adaptability to process disturbances with minimized risks. In this paper the features of the VSF ("Vertical Smooth Flow") SX technology are described, such as the separated pumping and mixing, the homogenous gentle mixing, the droplet coalescence and the ultra pure settling. A major advantage of the mixing technology is the high stage efficiency of above 99 per cent. The connection between this and some features of the settler front section is clarified. The present design of VSF plants is based on experience of existing operations at, for example, Zaldivar, Radomiro, Morenci, Kokkola and Harjavalta. These production plants cover a unit capacity range of 60 to 3,600 m3/h expressed as a total flow. It is evident that there are no restrictive factors to increase the total flow up to 5,000-6,000 m3/h by introducing the VSF technology. The copper SX technology has a long history reflecting many individual features of the separate copper SX plants. Still it is necessary to verify all actual running parameters by pilot tests taking into account impurities, chemicals used etc. The design of SX plants is not only about the delivery of equipment but also a process concept, and it is best tailor-made and adapted to specific local requirements.

Jan 1, 1999

By Tom Marttila

During the last few years, when a new tankhouse or a major modernization has been planned, automatic or semiautomatic crane and grab systems have at least been considered. It seems that in the future tankhouse managers for new, modernized and even old tankhouses will be looking for a proven and reliable system for automatically moving and positioning electrode loads in the tankhouse and in storage areas. In this paper, we will describe the Wenmec solution for automatic electrode handling. The advantages of automatic handling and very accurate electrode positioning will be discussed, and the way Wenmec has solved the problems in mechanical construction and in automatic, accurate and reliable positioning will be presented.

Jan 1, 1990

By Marco Pasetto

The possibility to re-use marginal materials (by-products) deriving from industrial activities in the construction of road infrastructures, as total or partial substitution of natural aggregates, successfully combines demands for economy and environmental sustainability. The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, to verify the suitability of a particular type of electric arc furnace slag to be recycled in the lithic skeleton of high-performance asphalt mixes (porous asphalt, high modulus mixes, stone mastic asphalt, nonskid surfacings) for road and airport flexible pavements. the process of transformation of iron and steel slag into a product that can be used in road building is described, along with the characterisation of the mixtures, plus an analysis of the results of a wide battery of mechanical-performance tests. This study forms part of wider theoretical ? experimental research being done at the University of Padova in order to improve knowledge of the characteristics of succedaneum materials and check their possible applications in road and airport construction.

Jan 1, 2006

By A. Niedbalska

A technique was developed for low pressure diamond synthesis using a specially prepared glassy carbon. The glassy carbon is produced in the form of solid plates by slow carbonization process of phenol formaldehyde resin interrupted at temperatures of 1273° K, 1073° K, and 923° K. The diamond synthesis is performed using cobalt plates as a catalyst-solvent. Synthesis was carried out at applied pressures of 6.0 and 3.8 GPa and a temperature of 1970° K and 2170° K. The products were analyzed by the x-ray powder dyffraction method and by microprobe to identify the diamond crystallites. The samples were taken from the place of contact between the glassy carbon and the cobalt catalyst. They were separated from the charge by a chemical method. Diamonds of the best form and the largest size were obtained at pressures that were much lower than those used in the traditional graphite method of diamond synthesis.

Jan 1, 1989

By John E. Dutrizac, Tzong T. Chen

"Laboratory experiments were undertaken to ascertain the behaviour of various ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C and in the presence of 40 or 50 g/L of hematite seed. Copper, nickel and zinc are not significantly incorporated in hematite precipitates. Although the nickel contents increase to 0.22% as the Ni concentration increases to 60 g/L, the solid solution Ni contents are low relative to the bulk Ni contents. Thus, part of the Ni may be present as tiny particles of poorly soluble NiS04.H20. Increasing germanium concentrations to 2,000 mg/L result in products containing up to 0.59% Ge. The Ge occurs either in solid solution in the hematite or is adsorbed on the nanometer-size hematite crystallites. Increasing As(V) concentrations to 10 g/L increase the AsO4 contents of the products up to 16%. However, the products consist of hematite together with As04-containing Fe(SO4)(OH) and an unknown Fe-AsO4 species. All the hematite products contain - 1% SO4 which appears to be adsorbed on the nanometer-size hematite crystallites.IntroductionDissolved iron is a common impurity in most hydrometallurgical processing circuits and, generally, the iron must be eliminated prior to the subsequent recovery of the sought after metals. Simple neutralization of iron-rich solutions yields slurries which are difficult to thicken and filter. To address these concerns, the jarosite, goethite and hematite processes have been developed, and these technologies are able to reject the dissolved iron in a readily filterable form [1]. Despite its higher cost, the hematite process offers several potential advantages. Because hematite is an iron-rich, high-density compound, its formation would reduce the mass of residue and the size of a residue storage pond. Hematite is the thermodynamically stable form of iron under ambient conditions, and this stability would facilitate the impoundment of hematite precipitates. Furthermore, hematite has some market potential for cement manufacture and even for iron making [2]. In all the commercial hematite processes, the dissolved ferric ions are first reduced to the ferrous state. Subsequently, the pH of the solution is adjusted and the solution is then oxidized. The ferric ions gradually generated during solution oxidation hydrolyze and precipitate mostly as hematite, although commercial hematite products also contain trace or minor amounts of jarosite-type compounds. However, there are potential advantages in precipitating hematite directly from ferric ion solutions, as the reduction and subsequent oxidation of the iron are not required. Although the precipitation of hematite directly from relatively concentrated ferric sulphate solutions (up to 0.5 M Fe(SO4)is) was recently demonstrated [3], the behaviour of impurity species during hematite precipitation is largely unknown. To address this issue, systematic laboratory experiments were undertaken to ascertain the behaviour of a number of ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C, and the results are presented in this paper."

Jan 1, 2012

By Rolando Campos

The CODELCO-CHILE Teniente Converter Technology, is presently being applied in four Chilean smelters (Caletones, Chuquicamata, Potrerillos and ENAMI-Ventanas). A Teniente Converter is due to be used at ENAMI-Hernan Videla Lira (Paipote) smelter in the near future. Also, a Teniente Converter is to be installed as part of a retrofit project for Nkana smelter of Zambia Consolidated Copper Mines Ltd. (ZCCM). The charge to be treated through this smelter will consist of a blend of concentrate arisings from the various concentrators within the ZCCM group. The present status on the application of the Teniente Converter Technology at Caletones smelter as well as its projected performance when used at Nkana smelter, are presented in this paper. The design operational basis, autogenous smelting throughputs, concentrate to matte ratios and benefits due to the use of technical oxygen, are presented and analysed.

Jan 1, 1992

By D. M. Hausen

A refractory siliceous low-grade silver ore (265 g/t Ag) from a prospect in Sonora, Mexico was investigated mineralogically and metallurgically to evaluate extraction of the silver by conventional methods. Approximately half of the silver was recoverable, occurring as coarsely crystalline acanthite (70-300 Am) that was liberated in material crushed to minus 10 mesh. The remaining silver is refractory and occurs mostly as finely locked (-2 to 0.2 Am) acanthite in cherty quartz, and as minor amounts of finely disseminated stylotypite or freibergite in fluorite. The mineralogic data have thus served to explain the 50-60% recovery of silver by flotation and cyanidation.

Jan 1, 1991

By C. Gasparrini

Mineralogy may be applied to the selection of appropriate separation techniques, as well as to assist in the evaluation of problems causing loss of metals and other economically important elements during plant processing. Mineralogic studies may thus help develop techniques to optimize metal recoveries. The present paper describes how such factors as the minerals in which the elements of interest are concentrated, their chemistry, the chemistry of the associated minerals, grain size and textural associations with other minerals in the ore, may affect decisions on separation techniques for the recovery of economic elements. A number of case studies are described in which the mineralogical observation of ore samples has revealed the cause of problems experienced in the extraction of select precious and base metals, or has been decisive in the choice of appropriate techniques for recovery.

Jan 1, 1981

By Tarek M. Abd El Hamid, Suzane Ali

"Treatment of industrial waste materials is created serious problem in Egypt. Aluminium sludge is generated as a by-product from aluminium household industry which contains significantly high alumina content exceeding 90%. This by-product randomly disposed and creates serious environment problems to locate community. To develop the treatment process of this material, the recovery of high purity alumina and identify the potential application is being the primary objective, This paper represents the recovery process of alumina process waste sludge High purity alumina material <99.8% aluminium oxide with originate particle size 0.125-0.420mm and apparent density 0.39g/cm3 was obtained with a specific surface area 139m2/g. Alumina produced was modified by cerium oxide doped alumina. The catalytic activity and selectivity was investigated in conversion of iso-propanol via dehydrogenation reaction yielding only acetone indicating an excellent selectivity the dehydrogenation. The presence of 10% CeO2 increase in the catalytic activity of 82% for the originated alumina. Introduction Approximately 20 thousand tons of aluminium waste produced in Egypt in 2006 with increasing amounts expected in succeeding years. A part of this waste contains organics impurities which coexisted with aluminium waste as a result of manufacture final aluminium products, waste usually content <1 to 2 wt% of organic carbon. It's generally admitted that the organic species are present in the form of lubricant oils used in rolling and pressing equipments for aluminium sheet. Both industry and government face possible high-cost disposal problems that more magnified by large volume of waste produced. The alumina recovery leachable study conduct in this paper had the following objectives: 1- Develop a process that can provide an environmentally acceptable residue and also recover the available alumina. 2- Evaluate the alumina produced in terms of grade and catalytic application."

Jan 1, 2008

By Geir Wedde, Anders Sorhuus

"Vast quantities of energy are released as heat to the environment from industrial operations. Many countries target waste heat recovery to mitigate CO2 emission. Exhaust gases from industries such as primary aluminium smelting, carry a substantial portion of the waste heat generated. For a cost efficient capture of more valuable heat (higher exergy), heat exchangers should operate on the exhaust gases upstream of the gas treatment plants. Heat exchange surface would be exposed to dust laden gases with risk of fouling. Heat exchangers of innovated design and operation have overcome the potential of excessive fouling rates. Heat exchangers of the ""shell and tube"" design have been demonstrated for exhaust gases from ferroalloy as well as primary aluminium smelters. In addition to the heat recovery, gas cooling results in smaller gas treatment plants with lower costs and reduced emission. The aluminium experience is exampled in the paper.IntroductionIndustrial usage of energy continues to grow as a result of increasing volumes of production, a trend that is likely to continue in the coming decades as living standards keep rising globally. World energy consumption (Figure la) is to grow 49 % by 2035 (ref. 2010) as reported by EIA [1]. The industrial sector consumes somewhat more than 50% of the total world energy consumption predominantly the energy increased demand comes from non-OECD countries in Asia. The industrial consumption by production of metals iron and steel accounts for 14 % and for non-ferrous metals 3 % mostly for aluminium production (Figure lb). Aluminium production will be discussed in this paper as an example of an industry with large quantities of waste heat to recover"

Jan 1, 2012

By Mark William Kennedy

"Electric furnaces containing high quantities of slag are applied in many areas of pyrometallurgy, often for smelting or slag cleaning. A variety of ratios or rules of thumb have been employed in the industry for the dimensioning of these vessels, in most cases with no clear technical basis.In this paper, several design guidelines are presented (electrode size, spacing, vessel dimensions, energy intensity, etc.) as an attempt to provide some technical basis for optimal dimensioning.Furnace heat generation is related to side wall copper cooler heat losses, in an attempt to establish a methodical design strategy particularly for minimum electrode to wall spacing for modern furnaces with cooled linings.Issues regarding the true nature of heat production in a slag furnace are discussed with regards to the possible impact on accurate modeling and design.IntroductionSlag furnaces have passed through a number of design 'generations' characterized by increasing energy intensities, improved electrode technologies and advancing development in their physical structure or 'furnace integrity' as shown in Table I f 1]. A 3rd generation furnace using ultra-high-power (UHP) graphite electrodes is shown in Figure 1, as a generic example of the types of physical structures present in modern slag furnace designs [1]."

Jan 1, 2012

By Robert A. Reiley

Under the traditional environmental paradigm, industry, stakeholders, and government impact the environment through production, consumption, and regulation. For more than twenty years, this paradigm has survived more or less unchallenged. Environmental action has followed a typical pattern: industry pollutes, the public clamors, government enacts legislation, and industry expenditures for pollution-control equipment soar. In the 1990&apos;s, many groups realize that command-and-control techniques may not be the most effective method of dealing with environmental issues in the new millennium. The need for regulatory reform became apparent in the 1980&apos;s after an accident at the Union Carbide plant in Bhopal, India. In addition, the prospects of an integrated European market and increased global trade sparked a need for common standards regarding the production of goods and services, which led to the adoption of the International Standards Organization (ISO) 9000 Quality Standards. These factors, and others, triggered the development of the Environmental Management System (EMS). Over the past decade, country-and industry- specific EMSs were developed. However, the IS0 realized the need for a single, internationally recognized standard that would be workable for any type organization. The goal of this standard is to promote economic competitiveness, remove trade barriers, and promote environmental protection. To this end, the IS0 14000 Standards were developed to provide business with a structure for managing environmental impacts. This article argues that a new paradigm has begun to transcend the old. Protection of the environment if shifting from "government drivers" to "market drivers". This shift means that industry and stakeholders, instead of government, are taking the lead to develop ways to protect the environment. This article also argues that government can use this new paradigm, in a time of declining budgets and regulatory reform, to continue to protect the environment through increased compliance monitoring and rigorous enforcement. Specifically, the IS0 14000 Standards can allow the government to reduce compliance costs, streamline permit and reporting requirements, and provide business with regulatory flexibility. Finally, this article argues that IS0 14000 will be central to the regulatory reform effort, because it can be internally implemented with little need for legislative intervention.

Jan 1, 1999

By W. P. lmrie

The recent years have seen many copper smelting operations become uneconomic due to a combination of low metal prices, high energy and labor costs, environmental requirements and high investment costs for modernization or replacement. Since a copper commodity requirement remains, the industry will recover, but many operations will need to determine which processes can offer the best prospect for economic operation and readiness for reliable investment and implementation. Corporate investment decisions involve the judgment of many factors in addition to topical technical aspects. Consideration of plant management and operational aspects are thus included. Taking account of such proven processes as conventional, flash and continuous smelting, plus modified conventional and new unproven processes, this paper gives a systematic approach to aid optimum choice for a modernization or grassroots investment. Actual achievements in energy form alternates, conservation and cost effectiveness are highlighted, and areas of remaining potential for energy saving are discussed.

Jan 1, 1983