Search Documents

By Hayati Karaman, Tevfik Güyagüler

In this paper fires due to spontaneous combustion in Middle Anatolian Lignite mine (OAL) which is the first fully mechanized underground lignite mine in Turkey, are studied. Since the installation of mechanization (1986), due to spontaneous heating, four panel fires namely, A01, A02, A03 and A04 have broken out. During these fires, the concentrations of carbon monoxide, methane and the velocity of air are measured continuously by the Micro Minos Environmental monitoring system. For each fire, the environment where fire has started is examined and the possible causes of the fire are investigated. Also the precautions taken to extinguish the fire at different stages are described and the importance of the early detection of mine fire are discussed together with the limitations of the monitoring system and the practical difficulties observed during the fire.

Jan 1, 1995

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By Pradip

Bastnaesite, a rare-earth fluocarbonate, was separated from associated calcite and barite gangue minerals in the Mountain Pass, CA rare-earth ore beneficiation plant by froth flotation using fatty acids (tall oil) collector, lignin sulfonate depressant and soda ash modifier after high-temperature (steam) conditioning with reagents. Starting with a feed grade of 7.6% REO, concentrates having a grade of 65% REO can be produced at a recovery of around 80%. A detailed investigation consisting of Hallimond tube microflotation experiments, bench-scale tests with a laboratory Denver flotation cell, and predesigned plant campaigns was made to delineate the underlying surface chemistry involved in this separation and to develop an alternate reagent scheme to enhance the selectivity of separation for this ore. Our results clearly demonstrate the superiority of alkyl hydroxamates to the conventional fatty acid collectors that were being used in the plant. Our study also indicates the possibility of achieving the desired selectivity with alkyl hydroxamates even at room temperature, thus obviating the need for steam conditioning. A critical review of the literature on rare-earth mineral flotation suggests the possibility of designing a more selective reagent combination for the beneficiation of Mountain Pass rare-earth ore, using a methodology based on ab initio molecular modeling computations.

By Ray E. Harris

New developments have occurred in Wyoming's industrial minerals industry since the 32nd Forum on the Geology of Industrial Minerals in Laramie, Wyoming in 1996. The soda ash trona and bentonite industries have experienced overall growth. Gypsum and limestone production have remained constant, but have the potential for dramatic growth. The mining of zeolite ceased in 1997. The struggling dimension stone industry has increased production, but development has lagged behind the schedule predicted in 1996. The construction of a container glass plant and associated production of glass raw materials, as predicted in 1996 and imminent in 1998, is now on hold due to unforeseen market factors. Increases in railroad and highway construction have, and will, greatly increase the production of construction aggregate for local uses. An iron carbide industry, not foreseen in 1996, is in the planning stages.

Jan 1, 2001

By William Gleason

"Mining roots run deep in Glenrock, WY, a town that was founded in part, because of the coal mining that began in the late 1800s. But that rich history also now threatens large parts of the town that were built over the top of the mines. Like many towns in the Western United States, mining is a proud part of the historical fabric and heritage of the town, but the legacy issues from past mining activities continue to present challenges to modern-day engineers.In the case of Glenrock, a small town about 40 km (25 miles) east of Casper, it is flooding from a century of water that has accumulated in the down geologic dip of the furthest northeastern extent of 87 ha (217 acres) of mine workings that has made the town susceptible to sinkholes and other issues (Fig. 1).Full commercial coal mining production began in Glenrock in 1887 during the development of the Fremont, Elkhorn and Missouri Valley railway. Due to poor overlying roof rock and continuous flooding within Glenrock, Mines No. 1 and 2 were fully closed in 1909. During its history, an estimated 87 ha (217 acres) were mined with 50 to 60 percent extraction ratio within the eastern town limits through room-and-pillar mining. It is estimated that the mines produced 22 kt/a (25,000 stpy) during their lifetime. A century later, the water pressure built up in the northeastern most portion of the mine has created serious concerns for residents.In 2016, the Wyoming Department of Environmental Quality’s Abandoned Mine Lands Divisions (AML) investigated a number of subsidence events in the town including sinkholes following heavy precipitation. The AML investigations confirmed that most events were related to the previous mining in the area.Mitigation efforts on the mines were done in the 1980s and 1990s, but the problems in the town and in a nearby subdivision persisted, leading the AML to search for alternative solutions."

Nov 1, 2019

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By M. Popescu

In the southern part ?f the Occidental Carpathians an iron ore body embedded in crystalline schist was exploited. The presence of minerals such as magnetite, pyrite, pyro-chorine, allanite, monazite and xenotime, which also include within their structure substituted thorium isomorphic, was pointed out. The iron ore was processed by crushing, grinding and magnetic separation in order to obtain magnetite concentrates. The environment was affected by pollution generated by the mining activities. In 1995 due to the economic reasons, it was decided to cease mining exploitation and remediate the area. The paper presents the ecological impact caused by mining activities on a number of environmental targets and the population. The pollution sources, namely sterile dumps and mine waters are characterized (from the physical, chemical and radiometric point of view); the pollution pathways and theirs effects on potential targets, namely soil, vegetation, hydrographic network and population are identified as well. The degree of pollution due to all sources was assessed and maps of pollution sources distribution were generated. The supplementary effective doses for the population were assessed using rigorous scenarios and considering all exposure pathways. The rehabilitation plan includes solutions for dumps geometrization, covering and revegetation as well as mine waters management.

Jan 1, 2005

By Karen Bolm, Floyd Gray, Ailiang Gu, Kerry Caruthers, Carlos Velez, Laurie Wirt, Douglas M. Hirschberg

Understanding sources of dissolved metals and transport characteristics of acid drainage is needed to assist land-use strategies in mineralized regions, particularly in the semi-arid southwestern United States. Water- quality samples were collected from mined and un-mined parts of the Patagonia and southern Santa Rita Mountains of southern Arizona from streams, springs, seeps, adits, alluvial wells, and bedrock wells. Water quality during base-flow conditions was compared with that *of runoff samples from infrequent winter and summer storms. The largest fraction of annual discharge in these ephemeral streams consists of storm runoff, although springs provide a steady source of low discharge base flow to numerous intermittent perennial reaches. Several abandoned mines in the northern Patagonia Mountains contribute acid and heavy metals to streams. During base-flow conditions in mineralized areas, natural springs and intermittent stream reaches produce acidity but the volume is typically low and acidity is often diluted or neutralized down gradient. Overland runoff contains low concentrations of dissolved metals and moderate acidity, however, stream waters were strongly acidified and metal-laden from contact with abundant pyrite-bearing stream sediments derived from erosion of waste-rock material in and along the sides of the stream channel.

Jan 1, 2000

By Milton E. Jennings

On May 11, 1977, the SAMARCO 20-inch, 396-kilometer (246-mile) Pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO Project. This paper presents the background, description and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1978

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By Eugene W. Price

One of the most important fundamental characteristics of iron ore pellets is their porosity. This importance arises from the fact that the pores are the busy avenues whereby many changes are brought about in the life and form of the pellet from the time it is made until the iron it contains emerges as a molten stream from the blast furnace. As a green iron ore pellet is first heated in the drying cycle of a typical heat-hardening process, the pores act as conduits to allow the escape of steam from the water or vapor from the oil which served as binders to hold the green pellet together. After the release of the steam (or oil vapor) the pores then act as conduits whereby oxygen can enter the pellets to 1) convert magnetite (Fe304) to hematite (Fe203), if appropriate, and 2) promote solid state grain growth between adjacent particles of iron ore. The rate of oxidation and the rate of grain growth are directly related to pore size' and pore size distribution. Rate of oxidation is also directly influenced by length of pore and length of pore is obviously related to pellet diameter. It is well to keep in mind that the heat-hardening process does not harden the mineral grains themselves. What it does is weld them together to change the green pellet from a doughy mass, composed of thousands of tiny individual particles, into a strong, intergrown monolithic structure. In the blast furnace the pores again act as conduits for gases, but in this case they trans¬port reductants such as hydrogen (H2) and carbon monoxide (C0) which remove most of the oxygen from the ore. Rate of reduction is also directly related to pore size and pore size distribution.

Jan 1, 1967

By Jayson Ripke, Peter Amelunxen, Brandon Akerstrom, Fernanda Solís

It is commonly known in the industry that one of the key challenges for a greenfield project, such as Capstone Copper’s Santo Domingo project, is the obtention of samples for metallurgical testing and subsequent plant design. To face this challenge, the Santo Domingo project completed 169,692 meters of drilling. The material collected has been used for a variety of analysis including the economic recovery of iron, which contributes significant economic value to the Santo Domingo business case. Composite and variability samples, covering the main geological units considered in the life of mine (LOM) plan, were selected for bench and pilot scale testwork. Davis Tube Tests, small scale Low Intensity Magnetic Separation (LIMS) tests and a pilot utilizing a 48 in (1.2 m), diameter magnetic separation drum were completed. The testwork demonstrated that the Santo Domingo ore could achieve iron concentrate grades of 65% Fe - suitable for blast furnace, and 67% Fe - suitable for Direct Reduction, primarily by concentration of magnetite. The outcomes of this work have informed the iron concentrator plant design and scale up.

Feb 1, 2025

By CK Tsang, Jack Muir, Dharman Gersch, Joshua Barry

Correct face pressure is critical to safe operation of a closed face TBM. If inadequate face pressure is applied, this will lead to excessive ground movement, and may result in collapse of the tunnel face. Face pressure calculations are performed manually every few meters along the tunnel alignment. With the application of a 3D ground model, ground profile information can be extracted for automatic computation. This will significantly improve the efficiency and accuracy and is adaptable to changes in design parameters. This paper will discuss the development of automatic computation techniques in extracting information from a 3D ground model.

Jun 13, 2021

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By Biao Qiu

Longwall and/or room-and-pillar mining operations in multiple coal seams could not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize mine structures and subsequently induce additional strata movements. Mechanical models to utilize the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations as well as the mining interactions associated with multi-seam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multi-seam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multi-seam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By Rolland L. Blake

The Bureau of Mines is investigating the potential for in situ leach mining "(ISM) of gold and silver mineralization. This preliminary study examined samples from several types of deposits using light optical microscopy and the electron microprobe to characterize the ore and gangue minerals and their microscopic characteristics, including the spacial relations between the target minerals and likely natural fluid channelways. Low grade disseminated deposit types from the western U.S. were found to contain fracture-hosted or matrix-hosted gold and silver minerals, some of which are encapsulated by quartz or pyrite. Geologic features readily observed microscopically include ore and gangue mineral identity, size, and their association with each other and with fractures. Successful ISM application to gold and silver deposits needs this data to: (1) select the proper lixiviant based on chemical reactivity of the host rock, ore, and gangue minerals, (2) determine potential permeability characteristics when designing lixiviant flow patterns, and (3) understand potential problems of the lixiviant reaching encapsulated ore minerals. Careful examination of the geologic characteristics of each ore body is required because of the observed diversity of characteristics in deposits from the same "class" and even within the deposit itself.

Jan 1, 1989