Search Documents

By Bryson D. Trexler

Man's activity in developing, operating, and abandoning a mine often affects the quality of the ground water and surface water. Acid water drainage from mines is an example of an impact from mining that results in degradation of ground and surface water. New flow systems are created by the mining activity. The mining made possible complex chemical reactions that, with water movement, create a discharge of low pH, poor quality water. Remedies for these problems fall into two general solutions: 1) treatment of the end product and 2) reversal of some aspect of man's disturbance of the natural system. The relative reversibility of various aspects of man's impact from mining activities ranges from relatively easy to very difficult, from economically feasible to economically infeasible, and from technically possible to essentially impossible with present knowledge. The relative reversibility of a mine-related problem cannot be assessed without first understanding the detailed physical interactions that combine to form the problem. Acid water drainage is a combination of the availability of several chemical factors with the availability of water for a transport mechanism.

Jan 1, 1982

By R. F. McFarlin, H. E. El-Shall

Since its inception, the Institute of Phosphate Research has examined every promising proposal in order to find an economical, practical and environmentally sound method of dewatering phosphatic clays. The in-house development of the FIPR/DIPR process (DIPR = Dewatering Instantaneously with Pulp Recycle) would appear to answer that quest. When small amounts of fibrous materials are mixed with clay slurries and flocculent, rapid dewatering occurs. Clay solids contents of 20 to 25% can be attained by simply rolling the clay mass down an inclined screen. Higher solids (>40%) are reached by physically pressing the cake; e.g., with a belt press. Because mechanical pressing devices are too expensive for phosphatic clay treatment, FIPR has developed the "sandwich" method of simultaneously dewatering the phosphatic clays and reclaiming the mine cut, as well as a second alternate, the "median strip" proposal. Economic projections of these bench-scale alternates suggest that the FIPR/DIPR process should be no more costly than present practice, when credit is given for the simultaneous reclamation accomplished.

Jan 1, 1993

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By Serkan Saydam, Ercument Yalcin

This paper presents the results of Caldagi Nickel-Cobalt Ore Deposit's, located in Turkey, reserve and ultimate pit limit design analysis. Reserve analysis of any deposit requires two steps. First one is to constitute of block model of the deposit and second step is to generate ultimate pit limit. The block model of the Caldagi ore deposit has been created by means of geostatistics. The reserves of nickel and cobalt in this block model are defined as resource, approximately 12 million tons of nickel and 1 million tons of cobalt with average grades of 0.9% Ni and 0.03% Co, respectively. Ultimate pit limit analysis has been performed by considering economic, technical and legal factors. In this paper, the ultimate pit limits are generated by Lerchs & Grossmann (L&G) algorithm. As a consequence of ultimate pit limit design, total amount of tonnage to be excavated is 1.4 billions of tons, 700 million of which contains ore and 747 million of which is the tonnage of waste.

Jan 1, 2002

By H. Reginald Hardy, Xiaoqing Sun

Rheological models are widely accepted as a means of describing the mechanical behavior of geologic materials. It has been found, however, that rheological models developed for a specific stress level on the basis of linear visco-elasticity generally are not satisfactory at other stress levels. It has been suggested that the parameters of such models should be functions of stress level (Hardy, 1965; Kim, 1971). In this paper, continuous functions of stress have been utilized to obtain the required variation of Burgers model parameters with stress level. The model developed using these functions provides a constitutive relation which reflects the real time-dependent behavior of rock materials. The new model is capable of predicting the creep behavior over a wide range of stress levels and also predicts mechanical behavior under different loading condition (e.g. constant stress rate). It is also interesting to note that the mechanical behavior of individual elements in the model appear to reflect the different stages of brittle fracture in rocks (Bieniawski, 1967), namely; crack closure, elastic deformation, stable fracture propagation and unstable fracture propagation.

Jan 1, 1986

By Jerry M. Whiting, Samuel Frimpong

Superior ventures selection and the subsequent management of their development and production are crucial in the competitive environment of the upstream minerals and energy industry. An important element of this chain is the management of uncertainty and risk dynamics. In the world of faster and more complicated technological and environmental changes, international competition and commodity market dynamics, thorough and sophisticated valuation must be carried out to establish a venture's value and return on investment. Thus, managers and investors must use methods that respond to market dynamics, investment and feasibility study options and provide relevant information for strategic investment decisions. Conventional methods have no built-in procedures to help investors analyse these options. Modern financial methods based on the dynamic arbitrage theory overcome these and other limitations of conventional methods. In this study, dynamic arbitrage theory has been used to formulate 3D parabolic differential equations that govern the stochastic processes of a copper mining venture with ongoing feasibility studies. The alternate direction implicit algorithm is used to solve the numerical approximations of the differential equations and their boundary conditions. Phase dynamics of the venture have been analysed to provide investors the appropriate timing for strategic investment decisions. The study also shows the amount and value of appropriate feasibility studies required to maximize the value of the mining venture.

Jan 1, 1996

By A. L. Mular

Steady-state material balances calculated from data measured at various locations around process units are useful for many purposes, such as metallurgical accounting, on-line control, and the development of mathematical models. Often it is possible to calculate material balances by several independent procedures when excess measurement information, i.e., redundant data, is available. Clearly, if the data were collected without measurement errors, a theoretical condition never found in practice, all material balances calculated from redundant data would be in agreement. The real situation is that error exists in practical measurements, so that the results of material balances determined from available optional procedures differ. Consequently, best fit computational procedures to improve the material balances by taking measurement errors into account have been formulated. Such procedures can be used also to judge whether measurements are grossly in error due to either faulty observations or defective data sensing devices. A variety of mathematical techniques are available which serve to adjust raw data. The adjusted data permit mass balancing that does not depend on the computational method. To illustrate the need for an adjustment procedure, Table 1 shows a raw data set acquired around the Brenda Mines Ltd. No. 4 grinding circuit shown schematically in Fig. 1. At least seven optional ways to calculate a circulating load ratio may be employed. These are shown in Table 2 where, depending upon the calculation [ ]

Jan 1, 1979

By R. Jacobson

This paper presents comparison of proposed future solution and in-situ mining methods for in-situ leaching and recovery of uranium, gold, silver, and copper. We propose to show that in the future new extraction methods for each metal will eventually evolve for each hydrometallurgical process step, i.e. in-situ leaching, recovery, and concentration; precipitation and reduction; and drying, when required--without generating waste or bleed streams. In the future, to be highly profitable, these forms of mining will develop into an integrated system to eliminate waste streams using safe, powerful lixiviants. This integration will include, with some exceptions, improvements in the following areas of process development: 1. Lixiviant selection and in-situ leaching technique, 2. Target metal recovery and concentration (at a surface hydrometallurgical facility) from the circulating pregnant lixiviant stream, 3. Target metal precipitation or reduction, where decant water from the precipitate dewatering step is reusable for resin or solvent strip liquor (eluant), 4. Final preparation of target metal for sales, i.e. drying, purification, casting, packaging, 5. Restoration where most of the groundwater restoration process is performed at the same rate as multi-wellfield mining.

Jan 1, 1987

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By P. B. Moran, J. W. Rozelle, J. Forbort

"The Mount Todd gold mine is located approximately 50 km (31 miles) north of the town of Katherine in the Northern Territory (NT) of Australia just off the Stewart Highway, and was operated in the 1990s until 2000 (Fig. 1). After cessation of mining operations, meteoric precipitation and acid rock drainage (ARD) associated with surface water runoff continued to report to the retention ponds across the mine site. In 2000, the mine site entered receivership and the NT government became responsible for the care and maintenance program. In 2006, Vista Gold Corp. (as Vista Gold Australia) acquired the rights to resume exploration on the mine site without the financial responsibility of the environmental liability. In January 2007, Vista Gold assumed the care and maintenance activities on behalf of the NT government, with the environmental liability remaining with the NT government, with the goal of reinitiating mining operations. A critical path component of the planned upgrades to the existing mine/milling facilities and infrastructure was the development of a cost effective treatment and dewatering program for the approximately 11 GL (2,900 million gal) of ARD stored in the Batman Pit (RP3), which has a maximum capacity of approximately 12 GL (3,200 million gal). The Batman Pit must be dewatered in order for Vista Gold to restart mining activities. The Batman Pit Lake had reached a maximum water depth of 104 m (341 ft) when Vista Gold initiated water level monitoring. It is important to note that the ARD water in the Batman Pit has been pumped into it from 2000 to 2012 under an NT government-approved environmental control program.The Batman Pit has virtually no connection to the local ground water regime due to the intensive silicification that accompanied the mineralizing event. In October 2012, just prior to treatment, the pit lake profile was characterized by uniform acidic pH (approximately pH 3.2) and oxic conditions (dissolved oxygen greater than 7 mg/L with depth (Fig. 2). The temperature decreased by approximately 4 °C (39 °F) between the lake surface and approximately 20 m (66 ft) deep, and remained near constant with increasing depth. This temperature difference is believed to be associated with an existing shallow mine bench at approximately 20 m (66 ft) deep around the perimeter of the pit. Similarly, electrical conductivity, an estimate of total dissolved solids, decreased by about 85 microSiemens per centimeter (µS/cm) from 2,800 to 2,715 µS/cm between 10 and 20 m (33 and 66 ft)."

Apr 1, 2016

By Nick Karlin

Dragados USA is constructing the LA Effluent Outfall Tunnel, a 7-mile, 18 ft internal diameter effluent discharge tunnel, utilizing a 21.6 ft (6.585 m) Herrenknecht Mixshield TBM. This paper highlights the means and methods used for TBM launch from a 55 ft diameter shaft excavated in wet with diaphragm wall support of excavation. This included SEM excavation of jet grout blocks for starter and tail tunnels, temporary concrete structures and steel installations, TBM sealing system, umbilical management for TBM hydraulic, electric and bentonite circuits as well as complex segment delivery logistics. The many launching challenges were overcome thanks to the innovative approaches from the project team.

Jun 13, 2023

By William R. Taylor

The information I have concerning the early in situ uranium mining activities in Texas is "sketchy." Apparently, the first test was conducted between 1967 and 1971 in Gonzales County, north of Yorktown, at the Dueterstat Site, by, City Service. Other tests were run in Webb County at the Bruni Site, and in Live Oak County at the Burns and Clay-West Sites in the early 1970's. During this period the Texas Water Quality Board maintained a general surveillance of these tests. In mid-1974, Mr. Glen Davis walked into our Austin offices and requested a permit for Atlantic Richfield's first in situ uranium mine. This permit, issued in January, 1975, was for 3 acres of production, and was the first such permit issued in the United States. It formalized the regulation of in-situ uranium mining in Texas. The 4 years since then have been characterized by growth and change. Today there are 20 permits approved for approximately 2,000 production acres. These permits are issued to 8 companies at 13 sites in 6 counties. There are 7 additional permits being processed, or on the verge of being applied for. These will involve possibly another 2,000 production acres, 3 more companies in one more county.

Jan 1, 1979

By J. C. Franklin

The U.S. Department of the Interior, Bureau of Mines, has developed a data acquisition system to continuously monitor radon, working level, absolute pressure, temperature, relative humidity, and air velocity. Data have been taken in intake and exhaust drifts, working stopes, and sealed-off areas of positive and negative ventilated uranium mines. Radon emanation rates, ranging from 1.7- to 12.2 x 2 10-l4 Ci/cm /sec were determined in four mines. The ratios of short duration, primary fan shutdown time to radon normalization time were 1 to 2 and 1 to 4, respectively, for-negatively and positively ventilated mines. Blasting and slushing caused radon increases of 160 and 67 percent, respectively.

Jan 1, 1980

By Stephen V. Thompson

Within recent years portable seismic refraction units have found their place in the industry for shallow investigations, Completely portable, relatively inexpensive and of proven accuracy, the portable refraction seismograph is an electronic tool in an electronic age. The age of electronic instrumentation has seen the development of seismic reflection and refraction equipment for deep exploration, especially in the petroleum industry. Large, expensive units, normally truck-mounted and utilizing explosives, are being used successfully for this type of sub- surface investigation. The portable seismograph utilizes the same theory for shallow work as that applied to deep refraction seismology.

Jan 1, 1964

By Gülhan Özbayoglu, Yusuf Ziya Akgök

The effect of cooling rate on the flotation behaviour of copper slags of flash smelter plant in Samsun was investigated. Fresh molten slag was solidified in laboratory scale in three different ways. All the samples were characterized by chemical and mineralogical analyses. The chemical analyses showed that samples prepared from fresh slag had 0.9 to 1 % Cu with 40 % Fe and 30 to 32 % SO2. Old pit slag samples contained between 1 to 3% copper. Microphotographs showed that rapidly cooled slags showed fine size distributions, e.g. the copper grains in granulated slag had sizes in 1-2 microns. On the other hand, the size of copper grains in slowly cooled slags increased above 40 microns. Flotation tests carried out by using potassium amyl xanthate and Flotanol-C showed that slowly cooled slag reduced the copper losses in the tailing and improved the grade of concentrate. Under the light of laboratory investigation, the pit dimensions of Samsun Plant have been modified which resulted in a pronounced improvement of the grade and recovery of concentrate produced at Samsun slag flotation circuit.

Jan 1, 1995

By Luis Pommier

In the United States, about one-quarter of the fuel oil and natural gas consumption is associated with power production in utility and industrial boilers and process heat needs in industrial furnaces. Coal has been an attractive candidate for replacement of these premium fuels because of its low cost, but there are penalties associated with the solid fuel form. In many cases pulverized coal is unacceptable as a premium fuel replacement because of the extensive cost of retrofitting an existing boiler designed to burn oil or gas. In the cases of synthetic fuels from coal, research and development still has a long way to go and the costs of research and development are very high. Another option which appears very attractive is the use of solid coal in a liquid fuel form, coal slurry fuels. Occidental Research Corporation (ORC) has been developing coal slurry fuels in conjunction with Island Creek Coal (ICC,) Occidental Petroleum's wholly-owned subsidiary. Both Coal-Oil Mixtures and Coal -Water Mixtures are under development. ICC is a large eastern coal producer, engaged in the production and marketing of bituminous coal, both utility steam and high quality/low volatile metallurgical coals. A sister division, Sheridan Enterprises is engaged in the development of western coals.

Jan 1, 1983

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

By Michael E. Mcllwain, Lee O. Nelson, Robert D. Rogers, James H. Wolfram

Examination of the economics and environmental consequences associated with phosphate fertilizer production documents the necessity for development of innovative production technologies. Evidence of phosphate ore's susceptibility to microbial alteration indicates that it will be an ideal candidate for industrial-scale bioseparation. There are at least two applications for the biosolu- bilization technology: (1) an industrial-scale bio- process similar to the presently used wet acid process and (2) production of small prills (bio- bead) containing unprocessed rock phosphate and the biological ingredients necessary to promote phosphate solubilization. At the present stage of development, the biobead technology is the preferred application. It is an energy-efficient "green" technology that will dramatically reduce the amount of solid waste and air emissions produced by the phosphate industry.

Jan 1, 1999

By S. K. MONDAL, K. K. K. SINGH, S. Singh, R. K. TIWARY, S. K. Chaulya, G. C. MONDAL, R. S. Singh, T. B. SINGH

In this work, a comprehensive field study was carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling was conducted to envisage dust concentration due to existing and closed mines in the region. The air quality modeling exercise predicted that particulate-matter levels of PM10 and PM2.5 might increase in the ranges of 3.2 to 23.1 and 2.1 to 8.9 μg/m3, respectively, due to mining activities when some of the closed mines will be operated in the region without controlled emission. The predicted total PM10 and PM2.5 at the selected receptor locations were in the ranges of 86.39 to 194.89 and 34.82 to 99.55 μg/m3, respectively. Adequate measures were suggested to control air pollution from mining activities, and an intelligent dry fog system was designed to suppress dust emission efficiently from mineral processing plants and opencast mines. The developed system has special features for facilitating eco-friendly mining.