Search Documents

By David R. Klug, Chris Gause, Troy L. Page

The Inter-Island Tunnel is one of two undersea tunnels which are part of the Boston Harbor Clean-Up Program. The tunnel is 7.7 km (25,160 ft) long, bored to a 4.3 m (14 ft) diameter in the Cambridge Argillite Formation and was finished to a 3.5 m (11.5 ft) diameter final concrete lining. The owner is the Massachusetts Water Resources Authority (MWRA) who is a regional authority responsible for overall design and construction. The tunnel's primary purpose is the transport of untreated effluent from Nut Island facility in Quincy, MA to the new treatment plant at Deer Island. Two sludge lines are installed for the transport of sludge from Deer Island to Nut Island. During construction the contractor encountered fault zones, fractured strata, and soft ground tunnel sections which liberated more ground water than was originally anticipated by the project designer. Ground water was controlled during mining and the placing of the final lining. The final lining of cast-in-place concrete had to be backfill grouted to cut off water inflows and provide contact for equal tunnel loading which is critical in long-term design. This paper deals with an engineered backfill grouting system which was the first of its type to be used in North America. It discusses the geological conditions encountered, the design criteria used in the evaluation process, and an indepth review of the various system components. It demonstrates how contractors can use knowledgeable and professional industry suppliers to solve difficult construction problems.

Jan 1, 1999

By Andrzej M. Wala

A prototype expert system for planning and designing an underground coal mine has been developed in a doctoral study at the University of Kentucky. This prototype expert system for underground coal mine planning and designing consists of a number of knowledge bases concerning different elements of design (e.g., ground control, excavation and bulk materials handling, ventilation, etc.). The objective of this paper is to present the development process of the ventilation design knowledge base for this prototype. This expert system prototype is intended for building an instructional expert system for underground coal mine design. Therefore, the undergraduate course on mine design has been used as the basis, for its development. Because of the availability of knowledge and expertise, this research study has been limited to development of a knowledge model for the Appalachian coal mining region.

Jan 1, 1993

By Henry J. Jacoby

This report concerns Contract No. 3B of the Port Richmond Project, for the Department of Water Resources of the City of New York. It involves the construction of 7, 000 ft. of 7 ft. finish I. D. interceptor sewer by tunneling in soft ground, as well as associated manholes, regulator chambers, siphons and miscellaneous sewers and structures, beneath a heavily travelled perimeter road in Staten Island. The Contractor is Richmond Constructors, a joint venture of Grow Tunneling Corp., sponsor, MacLean Grove & Company, Incorporated, Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Project manager is Paul DeMarco, Vice-President of Grow Tunneling Corp. The cortract, as designed and bid, requires the use of liner plates 101 -0" O. D., and both cast iron and steel designs of several widths were included in the bid documents by the owner. The specifications also required the contractor to install and put into operating condition, prior to commencement of mining, a complete low pressure compressed air plant and all accessories for mining in compressed air, even though the contractor was given the option of using other methods of ground water control. A third requirement of the specifications was that a shield be used, either manual or mechanical, and with full provision for "breasting". BACKGROUND The first soft ground shield driven tunnel in the United States was in New York City and was built under Broadway in lower Manhattan in 1869

Jan 1, 1974

By D. Watson

The Henderson mine has more than 20 years experience and has placed a combined total of more than 400,000 m3 (520,000 cy) of shotcrete and concrete. Over the last 20 years the mine has used a variety of equipment for placing concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Henderson has recently received a state of the art wet shotcrete placer, automated its batch plant, fabricated a mobile concrete form jumbo and is soon to receive a new concrete transport truck.

Jan 1, 1992

By R. A. Hevia

Florida Power and Light is the fifth largest investor-owned electric utility in the country. It has a service territory that covers 35 counties, or 28,000 square miles, 2.5 million customers, and serves 5.6 million people. The total installed capacity is 13,470 MW, generated by four nuclear units, 36 oil and/or gas fired units, and 48 gas turbine units. Traditionally, FPL has been an oil-based utility. In 1979, this dependency on oil became obvious when 42 million barrels of oil were burned during the year. At that time, it was also projected that, based on the current estimates of customer growth and available generation capacity through 1990, FPL's residual fuel oil consumption would increase from the 1979 level of 42 million barrels (6.7 million m3) per year to approximately 55 million barrels (8.7 million m3) per year by the mid-1990's. Concern over this was further aggravated by the fact that it was difficult to estimate both the price and quantity of fuel oil that would be available over the next decade since changes in the world market, decisions by oil producers and refiners, and international political developments would all affect the availability of oil. Also, at that time, the price of residual fuel oil had increased drastically, and there was no reason to think that these prices would soon stabilize. Thus, oil back-out became a primary objective of FPL and since then, FPL has been actively investigating ways to decrease fuel oil consumption.

Jan 1, 1985

By W. H. Langer

Around the beginning of the 20th Century, annual aggregate production in the United States amounted to about 50 million short tons. Today annual aggregate production is nearly 2.5 billion tons. Over a third of the States in the country produce more aggregate than the Nation did at the turn of the century. I would like to describe some of the historical events that allowed this nearly 50 fold increase in aggregate production. You might wonder why I want to talk about history. Some of our best ideas lie buried in the past, waiting to be rediscovered in the present. Almost every issue that the aggregate industry experiences today has been recognized for at least a decade; many of those issues have been recognized for a half a century; and a few of them have been recognized for nearly a century. The main reason for this article is to save the past from the forgetful indifference of the present-to faithfully preserve the past, to illustrate the insights of our predecessors, and to demonstrate how little of what we know today is really new.

Jan 1, 1998

By Robert L. Randall

The mineral industries have a continuing need for market forecasting and analysis for a variety of purposes, among which are organization and control of the sales effort, financial and corporate planning, and evaluation of the anticipated revenue from investment in proposed projects. For anything beyond the simplest extrapolation, some kind of economic reasoning or analysis is called for, which may or may not be incorporated into a formal or quantitative model. The principles described here apply to most of the commercially significant minerals and metals. The examples are drawn largely from the copper market, as it is the one with which I have the most practical experience. Practical forecasting is the process of analysis and synthesis from three categories of knowledge: facts and statistics, theory, and practical knowledge and informed opinion. Although many attempts have been made to build forecasts on only one of these three pillars, none has been successful as an operating procedure because of the lack of balance. There are no facts about the future-only about the present and the past. Facts can illuminate the future, but the future can be described only in terms of probability or more or less likely states of affairs-not as a continuous extension of the past and present. Likewise, theory, although useful as an organizing discipline and for providing a methodology of analysis, is inadequate for the complexities of reality. This is especially so when there is feedback between plans and forecasts to produce a new outcome and when there are significant elements of unpredictable free will, such as presidential jawboning or foreign policy considerations. Such elements are difficult to accommodate in neat theories, although they must certainly be reflected in the forecasts. Pure opinion frequently suffers from both a lack of-disciplined reasoning and the presence of biases or self-interest. While the future is unknown, it tends to cast its shadow before it; hence, forecasting is the art and science of positioning oneself so that the shadow becomes visible to the forecaster.

Jan 1, 1979

By Paul M. Bommer

Abstract. This cater presents the development of and results from a computer model of in-situ uranium leaching. This model uses a streamline-concentration balance approach and is useful with a vide range of reservoirs. It can be used with any type of veil system, in a reservoir with or without boundaries, and with any form of descriptive kinetics. The model also includes the effects of dispersion and consumption of oxidant by minerals other than uranium. The effects of areal sweep, variable uranium concentrations, variable permeability, and the presence of oxidant consumers on uranium production are shown and discussed.

Jan 1, 1979

By Patrick B. Kenny

Generally speaking, it is safe to address this conference as a conclave of Engineers, Owners' Agents, Governmental Representatives, and Contractors. As a group, we have assembled here to learn of our compatriots engaged in similiar underground operations throughout the United States and the World. We are here to learn of improved methods, higher technology, and better management. Through the acquisition of this knowledge, we each hope we can improve our own particular services, products and projects. This session is dedicated to a discussion of "Costs". The most apparent reason for a discussion of costs at this level is to expose subjects affecting costs and propose methods to reduce them. From that premise a contractor can identify three areas of discussion: design considerations, contract considerations, and governmental considerations. A fourth area of consideration is an introspective view of the contractor's role in the design construct process. Unnecessary costs and risks attributable to these areas are contributing excessively to ever increasing project and system costs. DESIGN CONSIDERATIONS On April 20, 1977 the Metropolitan Sanitary District of Greater Chicago accepted proposals for the Tunnel and Reservoir Plan on Contract A and Contract B. This letting called for construction of over 33 km (21 miles) of the Mainstream Tunnel bored at 9.75 m (32 ft) to 10.67 m (35 ft.) in diameter. Also included were all the appurtenant collecting and regulating structures. The proposal allowed the

Jan 1, 1979

By L. Hales

Process control systems have evolved from single loop control to distributed control with computer based expert control strategies. The next step is to add adaptive control to the expert control strategies. An object-oriented adaptive optimization approach is defined and simulated results are presented for a plant.

Jan 1, 1996

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994

By J. J. Komadina

Since the advent of resin-in-pulp (RIP) technology for treatment of uranium-bearing ores in the 1950?s to current carbon-in-pulp (CIP) processing of gold values, metallurgies and operators alike have wrestled with the problem of interstage screening. Early gold CIP plants such as at Homestake utilized externally mounted vibrating screens in conjunction with air lifts to effect carbon-pulp disengagement. Other operations world-wide have likewise adopted this technique with varying degrees of success. Subsequent development of in-tank launder screens both in South Africa and the United States have been of the air cleaned variety (EPAC)

Jan 1, 1988

By Patrick J. Maessen, Bart H. M. Hendrix

"In the Netherlands, the Dutch Tunnel Standard has been developed for the execution of road tunnel projects. The Dutch Tunnel Standard is based on the Dutch Tunnel Law (WARVW) which sets the minimum safety standard for road tunnels in the Netherlands. Uniformity of tunnels and the uniform perception of a tunnel by its users leads to a higher safety level. Therefore, several items in the Dutch Tunnel Standard are specifically developed to ensure safety in emergency situations through the plane of human factors. Taking human factors into account is important in regular traffic situations, but in an emergency situation, this can be vital. In this paper, the development and contents of the Dutch Tunnel Standard are explained in the first part and in the second part, the systems related to human factors are described. DUTCH TUNNEL LAW AND THE NEED FOR THE DUTCH TUNNEL STANDARD In the 90’s of last century and the early 2000’s, several serious accidents occurred in tunnels in Europe. These accidents involved fire and led to many casualties. After these accidents, the European Union decided to change the regulations for tunnel safety, leading to the EU directive 2004/54/EG. The primary goal of this directive is, that casualties are minimized in case of a calamity in a tunnel (e.g. fire). In the Netherlands, the EU directive led to the development of the tunnel law and a tunnel regulation (in 2006) to prescribe the safety features required for a safe tunnel. The new Dutch tunnel law – cited in the Building Act – was meant to make tunnel design easier – but resulted at first in the opposite effect. Tunnel design in the Netherlands and design standards of Rijkswaterstaat Rijkswaterstaat – the executing organisation of the Dutch Ministry of Infrastructure and the Environment – is the owner of the tunnels in the Dutch national motorway network, thus owner of the majority of the road tunnels in the Netherlands. In the early years of tunnel building in the Dutch national highway network (approximately 1950 – 1970), Rijkswaterstaat was not only owner, but also designer of its own assets. Most Dutch tunnels are submersed tunnels, because these type of tunnels provide a cost-effective way to make river crossings. Another type of tunnel that is used, is a TBM tunnel. Because of the geological conditions in the Netherlands (merely clay/peat and sand), there are no NATM or drill-and-blast tunnels in the Netherlands. Since the last decades, land tunnels (covered roads) are becoming more common to provide for multiple use of surface space and to meet more modern environmental regulations as traffic increases near densely populated areas. Tunnel lengths in the Netherlands vary from 500 m to 1.5 km for river crossings up to 6 km for the Western Scheldt (bored) tunnel. The lengths of land tunnels vary from 500 m up to 3 km. With these increasing lengths, some safety topics and design topics arise, topics that were non-issues in the past, when tunnels were only used as river crossings."

Jan 1, 2016

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

Following the recession of 2001, restrained consumer spending, declines in domestic manufacturing and industrial output, and increased unemployment led to a lack-luster year in the domestic economy. In 2002, the U.S. real gross domestic product (GPD) grew only 2.4%. Significant production declines in the U.S. metals industry were registered by copper, lead and zinc producers. Steel producers, despite a slight improvement in shipments, continued to face strong foreign competition, higher energy costs and lower prices for their products. Homebuilding and other domestic construction sectors— major consumers of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above 2001 levels. A strong U.S. dollar relative to other national currencies continued to weaken the competitive stance of U.S. metal and non-metal mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2003

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

By K. Hanumantha Rao, K. S. E. Forssberg, B. -M. Antti

Selective flotation of muscovite from a material containing muscovite (15.4%), biotite (13%), and siliceous gangue (quartz and feldspar), using a mixed collector system of sodium oleate and dodecylamine acetate has been described. Muscovite is found to float in preference to biotite, when the pulp is initially conditioned with oleate followed by amine at basic pH values. The results indicate that a product containing 63% muscovite with a recovery of 93% can be obtained, while using 75-150glt of oleate and 96 g/t of amine. The biotite grade and recovery are found to be around 30% and 20%, respectively. A good selectivity between muscovite and siliceous gangue is obtained. A final product containing 95% muscovite with an overall recovery of 75% is obtained when the flotation concentrate is subjected to magnetic separation. These studies indicate the possibility of separating muscovite from biotite by using a mixture of collectors.

Jan 1, 1991

By Giorgio Höfer-Öllinger, Peter Pointner, Manfred Stadlober

"SUMMARY Investigations from tunnel face are part of risk mitigation measures during the excavation works. With the tunnel equipment, percussion drillings of up to 30-40m can be achieved. Core drillings are state of art method for investigation exceeding 50m. At Koralm base tunnel, up to 270m deep percussion drillings were performed with drilling rigs and accompanied by an intensive investigation program. These investigations consisted of monitoring during the drilling, field tests (with packer, using the preventer, borehole imaging) and in laboratory. Percussion drillings are cheaper and save time of interruption of the excavation progress. INTRODUCTION As part of a proper risk management, horizontal advance drillings during excavation of underground works can be seen as state of art and meet wide acceptance. Core drillings, deep and shallow percussion drillings can be differed. The selection of the type of drilling, meanwhile, causes intensive discussions. On the one hand, only a core drilling allows a direct investigation of the rock mass expected during later excavation works. On the other hand core drillings are expensive in both cost and time – if there is no excavation progress during the investigation measures – in construction time. Percussion drillings can be performed as rapid investigation measure with the excavation equipment (“Jumbo”) allowing two dimensional image of the ground around the cross section. There is some limitation concerning a reasonable depth of approximately 30m and a borehole diameter of 76mm. The applications of preventer, packer or borehole imaging are hardly applicable. By use of a drilling rig depths of percussion drillings of several hundred meters can be achieved relative easily and there is less limitation of the borehole diameter. Installation of a preventer is possible, as well as packer tests and borehole measurements (imaging, gyroscope, borehole geophysics). The gap of information between core and percussion drilling cannot be closed completely, but it can be reduced substantially and sufficiently by combination of an intensive program of measurements and analysis accompanying the investigation works."

Jan 1, 2016

By C. W. Schultz

The distribution of material passing a screen, or a set of screens, is described by the equation [ ] where p = the probability that a single particle will pass the screen on a single presentation k = number of layers of screen cloth n = distance from head of screen expressed as number of screen openings. This model can be used to predict the performance of conventional screening operations (i.e., k = 1) as well as the so-called "statistical screening" operations. Using this technique, in which multiple identical layers of screen cloth are employed, screening can be carried out at a finer size than is possible with conventional techniques with no loss of separation efficiency.

Jan 1, 1969